2005-2008 Yaris · Service Manual ENGINE

P0300 Random / Multiple Cylinder Misfire Detected

Diagnostic trouble codes · Vehicles built from Nov 2006

Also covers:

DESCRIPTION

When the engine misfires, high concentrations of hydrocarbons enter the exhaust gas. Extremely high hydrocarbons concentration levels can cause increases in exhaust emission levels. High concentrations of hydrocarbons can also cause increases in the three way catalytic converter temperature, which may cause damage to the three way catalytic converter. To prevent these increases in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the three way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensors and the crankshaft position sensor. The camshaft position sensors are used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted as when the crankshaft rotation speed variations exceed predetermined thresholds.
If the misfire rate exceeds the threshold level, and could cause emission deterioration, the ECM illuminates the MIL and sets a DTC.
DTC No.
DTC Detection Condition
Trouble Area
P0300
Simultaneous misfiring of several cylinders detected
(2 trip detection logic)
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connections
  4. Ignition system
  5. Fuel injector
  6. Fuel pressure
  7. Mass air flow meter
  8. Engine coolant temperature sensor
  9. Compression pressure
  10. Valve clearance
  11. Valve timing
  12. PCV valve and hose
  13. PCV hose connection
  14. Air induction system
  15. ECM
P0301
P0302
P0303
P0304
Misfiring of specific cylinder detected
(2 trip detection logic)
When DTCs for misfiring cylinders are randomly set, but DTC P0300 is not set, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only set when several misfiring cylinders are detected at the same time.

WIRING DIAGRAM

A159160E01

CONFIRMATION DRIVING PATTERN

  1. Connect an intelligent tester to the DLC3.
  2. Turn the ignition switch on (IG).
  3. Turn the tester on.
  4. Record DTCs and freeze frame data.
  5. Using the tester, switch the ECM from normal mode to check mode (Click here).
  6. Read the misfire counts of each cylinder (Cylinder #1, #2, #3 and #4) with the engine in an idling condition. If any misfire count is displayed, skip the following confirmation driving pattern.
  7. Drive the vehicle several times with the conditions, such as engine rpm and engine load, shown in Misfire RPM and Misfire Load in the Data List.

    HINT:
    In order to store misfire DTCs, it is necessary to drive the vehicle for the period of time shown in the table below, with the Misfire RPM and Misfire Load in the Data List.
    Engine RPM
    Duration
    Idling
    8 minutes or more
    1,000
    4 minutes 30 seconds or more
    2,000
    2 minute 30 seconds or more
    3,000
    1 minute 30 seconds or more

  8. Check whether misfires have occurred by checking for DTCs and freeze frame data.

    HINT:
    Do not turn the ignition switch off until the stored DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data will be erased.

  9. Record the DTC(s), freeze frame data and misfire counts.
  10. Turn the ignition switch off and wait for at least 5 seconds.

INSPECTION PROCEDURE

HINT:
  1. If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
  2. Read freeze frame data using an intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the freeze frame data.
  4. If the misfire still cannot be reproduced even though the conditions stored in the freeze frame data have been duplicated, one of the following factors is considered to be a possible cause of the problem:
    1. The fuel level is low.
    2. Improper fuel is used.
    3. The spark plugs are dirty.
    4. The problem is complex and involves multiple factors.
  5. After finishing repairs, check that no misfire occurs in each cylinder (Cylinder #1, #2, #3 and #4).
  6. Be sure to confirm that no misfiring cylinder DTCs are set again by conducting the confirmation driving pattern, after the repairs.
  7. When either Short FT #1 or Long FT #1 in the freeze frame data is outside the range of +/-20%, the air fuel ratio may be rich (-20% or less) or lean (+20% or more).
  8. When the Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfires occurred only while warming up the engine.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    P0300, P0301, P0302, P0303 and/or P0304
    A
    P0300, P0301, P0302, P0303 and/or P0304 and other DTCs
    B

    HINT:
    If any DTCs other than P0300, P0301, P0302, P0303 and P0304 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Misfire RPM and Misfire Load.

  1. Read and note the Misfire RPM and Misfire Load (engine load) values.

    HINT:
    The Misfire RPM and Misfire Load indicate the vehicle conditions under which the misfire occurred.


NEXT


3. CHECK PCV HOSE CONNECTIONS

OK:
PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


4. CHECK MISFIRE COUNT (CYLINDER #1, #2, #3 AND #4)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Clear.

  1. Clear DTCs.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Cylinder #1 to #4 Misfire Rate.

  1. Start the engine.

  1. Drive the vehicle with the Misfire RPM and Misfire Load noted in the "READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD)" procedures above (Step "A").

  1. Read the Cylinder #1 to #4 Misfire Rate or DTCs displayed on the tester (Step "B").

    Result:
    Result
    Proceed to
    Most misfire occurs in only 1 or 2 cylinders
    A
    3 cylinders or more have equal misfire counts
    B

    HINT:
    1. If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
    2. If the freeze frame data's record of the ECT is below 75°C (167°F), the misfire may be detected only when the engine is cold.
    3. If the freeze frame data's record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.



B
Go to step 13
A


5. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL CUT #1 TO #4)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Start the engine.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.

  1. If a cylinder has a high misfire count, cut fuel to the cylinder. Compare the misfire count of the cylinder before fuel cut and after fuel cut.

    Result:
    Result
    Proceed to
    Misfire count of cylinder before fuel cut and after fuel cut roughly same
    A
    Misfire count of cylinder before fuel cut lower than after fuel cut
    B

    NOTICE:
    This Active Test cannot be performed while the vehicle is being driven.

    HINT:
    If the misfire count of the cylinder before and after the fuel cut are roughly the same, the cylinder is misfiring.
    If the misfire count of the cylinder before the fuel cut is lower than after the fuel cut, the cylinder misfires sometimes.



B
Go to step 9
A


6. CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER
  1. Measure the cylinder compression pressure of the misfiring cylinder (Click here).



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


7. INSPECT FUEL INJECTOR (POWER SOURCE)

  1. A157859E02
    Disconnect the fuel injector connectors.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C4-1 - Body ground
    Ignition switch on (IG)
    11 to 14 V
    C5-1 - Body ground
    Ignition switch on (IG)
    11 to 14 V
    C6-1 - Body ground
    Ignition switch on (IG)
    11 to 14 V
    C7-1 - Body ground
    Ignition switch on (IG)
    11 to 14 V

  1. Reconnect the fuel injector connectors.



NG
Go to step 20
OK


8. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)

  1. A106388E18
    Disconnect the fuel injector connectors (of the misfiring cylinder).

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    C4-2 - C20-108 (#10)
    Always
    Below 1 Ω
    C5-2 - C20-107 (#20)
    Always
    Below 1 Ω
    C6-2 - C20-106 (#30)
    Always
    Below 1 Ω
    C7-2 - C20-105 (#40)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    C4-2 or C20-108 (#10) - Body ground
    Always
    10 kΩ or higher
    C5-2 or C20-107 (#20) - Body ground
    Always
    10 kΩ or higher
    C6-2 or C20-106 (#30) - Body ground
    Always
    10 kΩ or higher
    C7-2 or C20-105 (#40) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the fuel injector connectors.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. CHECK SPARK PLUG

  1. A088861E08
    Remove the ignition coil and the spark plug of the misfiring cylinder.

  1. Measure the spark plug electrode gap.

    Standard gap:
    1.0 to 1.1 mm (0.039 to 0.043 in.)

  1. Check the electrode for carbon deposits.

    Recommended spark plug:
    Manufacturer
    Product
    DENSO
    SC20HR11

    NOTICE:
    If the electrode gap is larger than standard, replace the spark plug. Do not adjust the electrode gap.

  1. Reinstall the ignition coil and the spark plug.



NG
REPLACE SPARK PLUG
OK


10. CHECK FOR SPARKS
  1. Perform a spark test (Click here).

    OK:
    Sparks jump across electrode gap.

    CAUTION:
    Always disconnect all fuel injector connectors.



NG
Go to step 21
OK


11. INSPECT FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the fuel injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).



NG
REPLACE FUEL INJECTOR
OK


12. CHECK VALVE CLEARANCE OF MISFIRING CYLINDER (INSPECT VALVE LASH ADJUSTER)
  1. Check the valve lash adjuster and valve rocker arm of misfiring cylinder (Click here).



NG
REPAIR OR REPLACE VALVE LASH ADJUSTER ASSEMBLY
OK


13. CHECK AIR INDUCTION SYSTEM
  1. Check the intake system for vacuum leak.

    OK:
    No leak from intake system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


14. CHECK FUEL PRESSURE
  1. Check the fuel pressure (Click here).



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


15. READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature.
    With warm engine: 80°C to 100°C (176°C to 212°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
OK


16. INSPECT MASS AIR FLOW METER
  1. Read values using an intelligent tester (MAF).

    NOTICE:
    1. Turn the ignition switch off.
    2. Perform the inspection with the vehicle indoors and on a level surface.
    3. Perform the inspection of the mass air flow meter while it is installed in the air cleaner case (installed on the vehicle).
    4. During the test, do not use the exhaust air duct to perform suction on the exhaust pipe.

    1. Turn the ignition switch on (IG) (do not start the engine).

    2. Turn the tester on.

    3. Select the following menu items: Powertrain / Engine and ECT / Data List / MAF.

    4. Wait for 30 seconds, and read the values on the intelligent tester.

      Standard:
      Less than 0.19 g/sec

  1. Inspect the mass air flow meter.

    1. Remove the mass air flow meter (Click here).

    2. A154164E01
      Using a work light, check that the platinum filament (heater portion) in the mass air flow meter has no foreign matter attached.

      Standard:
      No foreign matter attached.

    3. Reinstall the mass air flow meter.



NG
REPLACE MASS AIR FLOW METER
OK


17. CHECK VALVE TIMING
A159445E01

HINT:
There are no marks on the cylinder head to match-up for the purpose of checking valve timing. Valve timing can only be inspected by lining up the colored plates on the timing chain with the marks on the pulleys. It may be necessary to remove and re-install the chain to match up the timing marks (Click here).



NG
ADJUST VALVE TIMING
OK


18. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


19. CHECK WHETHER DTC OUTPUT RECURS (DTC P0300, P0301, P0302, P0303 and/or P0304)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    No output
    A
    P0300, P0301, P0302, P0303 and/or P0304
    B



B
REPLACE ECM
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)

20. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - INTEGRATION RELAY)

  1. A159685E01
    Disconnect the fuel injector connectors.

  1. Remove the integration relay (IG2 relay) from the engine room R/B and J/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    C4-1 - 1B-4
    Always
    Below 1 Ω
    C5-1 - 1B-4
    Always
    Below 1 Ω
    C6-1 - 1B-4
    Always
    Below 1 Ω
    C7-1 - 1B-4
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    C4-1 or 1B-4 - Body ground
    Always
    10 kΩ or higher
    C5-1 or 1B-4 - Body ground
    Always
    10 kΩ or higher
    C6-1 or 1B-4 - Body ground
    Always
    10 kΩ or higher
    C7-1 or 1B-4 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the fuel injector connectors.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE ECM POWER SOURCE CIRCUIT (Click here)

21. CHECK NORMAL SPARK PLUG AND CHECK FOR SPARKS OF MISFIRING CYLINDER
  1. Change the installed spark plug with a spark plug that functions normally (good known).

  1. Perform a spark test (Click here).

    OK:
    Sparks jump across electrode gap.

    CAUTION:
    Always disconnect all fuel injector connectors.



NG
REPLACE IGNITION COIL
OK

REPLACE SPARK PLUG


← P0171 System Too Lean (Bank 1) (+ P0172) (from Nov 2006)P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) (+ P0328) (from Nov 2006) →