Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Lines for Short Circuit (LHD Models)

for Preparation Click here


DESCRIPTION

There may a short circuit in the CAN main wire and/or CAN branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 below 54Ω
  1. Short between CAN bus lines
  2. Brake actuator (skid control ECU)*1
  3. Power steering ECU
  4. ECM
  5. Center airbag sensor assembly
  6. Air conditioning amplifier*2
  7. Combination meter ECU
  8. Main body ECU
  9. D-CAN junction connector
  10. P-CAN junction connector
*1: w/ ABS
*2: w/ Air conditioning

WIRING DIAGRAM


E174038E05


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.CHECK CAN BUS LINES FOR SHORT CIRCUIT (DLC3 BRANCH WIRE)


    E160790E14
  1. Turn the ignition switch off.

  1. Disconnect the D41 D-CAN junction connector.



    C140672E44
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D15-6 (CANH) - D15-14 (CANL)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)
OK


2.CONNECT CONNECTOR
  1. Reconnect the D-CAN junction connector.


NEXT


3.CHECK CAN BUS LINES FOR SHORT CIRCUIT (P-CAN J/C SIDE)


    E160790E06
  1. Turn the ignition switch off.

  1. Disconnect the D42 P-CAN junction connector.



    C140672E44
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D15-6 (CANH) - D15-14 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 7
OK


4.CHECK CAN BUS LINES FOR SHORT CIRCUIT (P-CAN J/C - POWER STEERING ECU)


    E160790E10
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-4 (EPS) - D42-15 (EPS)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 13
OK


5.CHECK CAN BUS LINES FOR SHORT CIRCUIT (P-CAN J/C - MAIN BODY ECU)


    E160790E11
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-5 (J/B) - D42-16 (J/B)
    Ignition switch off
    1 Ω or higher



NG
Go to step 14
OK


6.CHECK CAN BUS LINES FOR SHORT CIRCUIT (P-CAN J/C - COMBINATION METER ECU)


    E160790E13
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-7 (MET) - D42-18 (MET)
    Ignition switch off
    1 Ω or higher



NG
Go to step 15
OK

REPLACE P-CAN J/C (JUNCTION CONNECTOR) 

7.CHECK CAN BUS LINES FOR SHORT CIRCUIT (D-CAN J/C - P-CAN J/C)


    E160790E03
  1. Turn the ignition switch off.

  1. Disconnect the D41 D-CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-11 (TORH) - D41-22 (TORH)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (D-CAN J/C - P-CAN J/C (CAN-H, CAN-L))
OK


8.CONNECT CONNECTOR
  1. Reconnect the P-CAN junction connector.


NEXT


9.CHECK CAN BUS LINES FOR SHORT CIRCUIT (D-CAN J/C - ECM)


    E160790E02
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-4 (EFI) - D41-15 (EFI)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 16
OK


10.CHECK CAN BUS LINES FOR SHORT CIRCUIT (D-CAN J/C - BRAKE ACTUATOR (SKID CONTROL ECU))

NOTICE:
For vehicles without ABS, go to step 11.



    E160790E07
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-1 (ABS) - D41-12 (ABS)
    Ignition switch off
    1 Ω or higher



NG
Go to step 17
OK


11.CHECK CAN BUS LINES FOR SHORT CIRCUIT (D-CAN J/C - AIR CONDITIONING AMPLIFIER)

NOTICE:
For vehicles without air conditioning, go to step 12.



    E160790E08
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-6 (A/C) - D41-17 (A/C)
    Ignition switch off
    1 Ω or higher



NG
Go to step 18
OK


12.CHECK CAN BUS LINES FOR SHORT CIRCUIT (D-CAN J/C - CENTER AIRBAG SENSOR ASSEMBLY)


    E160790E09
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-8 (A/B) - D41-19 (A/B)
    Ignition switch off
    1 Ω or higher



A
Go to step 19
OK

REPLACE D-CAN J/C (JUNCTION CONNECTOR) 

13.CHECK CAN BUS LINES FOR SHORT CIRCUIT (POWER STEERING ECU MAIN WIRE)


    G100242E34
  1. Disconnect the D31 power steering ECU connector.



    E160790E10
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-4 (EPS) - D42-15 (EPS)
    Ignition switch off
    1 MΩ or higher

Result 
Result
Proceed to
NG
A
OK (for Hatchback)
B
OK (for Sedan)
C


B
REPLACE POWER STEERING ECU (Click here)

C
REPLACE POWER STEERING ECU (Click here)
A

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO POWER STEERING ECU (CAN-H, CAN-L) 

14.CHECK CAN BUS LINES FOR SHORT CIRCUIT (MAIN BODY ECU BRANCH WIRE)


    C131840E13
  1. Disconnect the D33 main body ECU connector.



    E160790E11
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-5 (J/B) - D42-16 (J/B)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CAN-H, CAN-L)
OK

REPLACE MAIN BODY ECU 

15.CHECK CAN BUS LINES FOR SHORT CIRCUIT (COMBINATION METER ECU BRANCH WIRE)


    C139156E28
  1. Disconnect the D63 combination meter ECU connector.



    E160790E13
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-7 (MET) - D42-18 (MET)
    Ignition switch off
    1 MΩ or higher

Result 
Result
Proceed to
NG
A
OK (for Hatchback)
B
OK (for Sedan)
C


B
REPLACE COMBINATION METER ECU (Click here)

C
REPLACE COMBINATION METER ECU (Click here)
A

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO COMBINATION METER ECU (CAN-H, CAN-L) 

16.CHECK CAN BUS LINES FOR SHORT CIRCUIT (ECM MAIN WIRE)


    C125895E17
  1. Disconnect the A21 ECM connector.



    E160790E02
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-4 (EFI) - D41-15 (EFI)
    Ignition switch off
    1 MΩ or higher

Result 
Result
Proceed to
NG
A
OK (for 1NZ-FE)
B
OK (for 2NZ-FE)
C


B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CAN-H, CAN-L) 

17.CHECK CAN BUS LINES FOR SHORT CIRCUIT (BRAKE ACTUATOR (SKID CONTROL ECU) BRANCH WIRE)


    C168930E14
  1. for Hatchback:

    1. Disconnect the A15 brake actuator (skid control ECU) connector.



    2. E160790E07
    3. Measure the resistance according to the value(s) in the table below.

      HINT:
      The resistance must be measured after the D41 D-CAN junction connector is disconnected.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      D41-1 (ABS) - D41-12 (ABS)
      Ignition switch off
      1 MΩ or higher



    C118165E31
  1. for Sedan:

    1. Disconnect the A15 brake actuator (skid control ECU) connector.



    2. E160790E07
    3. Measure the resistance according to the value(s) in the table below.

      HINT:
      The resistance must be measured after the D41 D-CAN junction connector is disconnected.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      D41-1 (ABS) - D41-12 (ABS)
      Ignition switch off
      1 MΩ or higher

Result 
Result
Proceed to
NG
A
OK (for Hatchback)
B
OK (for Sedan)
C


B
REPLACE BRAKE ACTUATOR (SKID CONTROL ECU) (Click here)

C
REPLACE BRAKE ACTUATOR (SKID CONTROL ECU) (Click here)
A

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BRAKE ACTUATOR (SKID CONTROL ECU) (CAN-H, CAN-L) 

18.CHECK CAN BUS LINES FOR SHORT CIRCUIT (AIR CONDITIONING AMPLIFIER BRANCH WIRE)


    C105175E16
  1. Disconnect the E8 air conditioning amplifier connector.



    E160790E08
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-6 (A/C) - D41-17 (A/C)
    Ignition switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER (CAN-H, CAN-L)
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)  

19.CHECK CAN BUS LINES FOR SHORT CIRCUIT (CENTER AIRBAG SENSOR ASSEMBLY BRANCH WIRE)


    C131069E26
  1. Disconnect the D16 center airbag sensor assembly connector.



    E160790E09
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-8 (A/B) - D41-19 (A/B)
    Ignition switch off
    1 MΩ or higher

    Result 
    Result
    Proceed to
    NG
    A
    OK (for Hatchback)
    B
    OK (for Sedan)
    C



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
A

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CAN-H, CAN-L)