Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Line for Short to GND (LHD Models)

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus line and GND when there is resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3.

Symptom
Trouble Area
Resistance exists between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of DLC3.
  1. Short to GND
  2. Brake actuator (skid control ECU)*1
  3. Power steering ECU
  4. ECM
  5. Center airbag sensor assembly
  6. Air conditioning amplifier*2
  7. Combination meter ECU
  8. Main body ECU
*1: w/ ABS
*2: w/ Air conditioning

WIRING DIAGRAM


E174038E05


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.CHECK CAN BUS LINE FOR SHORT TO GND (DLC3 BRANCH WIRE)


    E160790E05
  1. Turn the ignition switch off.

  1. Disconnect the D41 D-CAN junction connector.



    C140672E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D15-6 (CANH) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher
    D15-14 (CANL) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)
OK


2.CONNECT CONNECTOR
  1. Reconnect the D-CAN junction connector.


NEXT


3.CHECK CAN BUS LINE FOR SHORT TO GND (P-CAN J/C SIDE)


    E160790E06
  1. Turn the ignition switch off.

  1. Disconnect the D42 P-CAN junction connector.



    C140672E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D15-6 (CANH) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher
    D15-14 (CANL) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
Go to step 10
OK


4.CHECK CAN BUS LINE FOR SHORT TO GND (P-CAN J/C - POWER STEERING ECU)


    E160792E13
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-4 (EPS) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher
    D42-15 (EPS) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
Go to step 7
OK


5.CHECK CAN BUS LINE FOR SHORT TO GND (P-CAN J/C - MAIN BODY ECU)


    E160792E51
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-5 (J/B) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher
    D42-16 (J/B) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
Go to step 8
OK


6.CHECK CAN BUS LINE FOR SHORT TO GND (P-CAN J/C - COMBINATION METER ECU)


    E160792E16
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-7 (MET) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher
    D42-18 (MET) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
Go to step 9
OK

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (D-CAN J/C - P-CAN J/C (CAN-H, CAN-L)) 

7.CHECK CAN BUS LINE FOR SHORT TO GND (POWER STEERING ECU)


    C140668E14
  1. Disconnect the D31 power steering ECU connector.



    E160792E13
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-4 (EPS) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher
    D42-15 (EPS) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher

    Result 
    Result
    Proceed to
    NG
    A
    OK (for Sedan)
    B
    OK (for Hatchback)
    C



B
REPLACE POWER STEERING ECU (Click here)

C
REPLACE POWER STEERING ECU (Click here)
A

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO POWER STEERING ECU (CAN-H, CAN-L) 

8.CHECK CAN BUS LINE FOR SHORT TO GND (MAIN BODY ECU BRANCH WIRE)


    C131840E13
  1. Disconnect the D33 main body ECU connector.



    E160792E51
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-5 (J/B) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher
    D42-16 (J/B) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CAN-H, CAN-L)
OK

REPLACE MAIN BODY ECU 

9.CHECK CAN BUS LINE FOR SHORT TO GND (COMBINATION METER ECU BRANCH WIRE)


    C139156E28
  1. Disconnect the D1 combination meter ECU connector.



    E160792E16
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D42 P-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D42-7 (MET) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher
    D42-18 (MET) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher

    Result 
    Result
    Proceed to
    NG
    A
    OK (for Sedan)
    B
    OK (for Hatchback)
    C



B
REPLACE COMBINATION METER ECU (Click here)

C
REPLACE COMBINATION METER ECU (Click here)
A

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO COMBINATION METER ECU (CAN-H, CAN-L) 

10.CONNECT CONNECTOR
  1. Reconnect the P-CAN junction connector.


NEXT


11.CHECK CAN BUS LINE FOR SHORT TO GND (D-CAN J/C - ECM)


    E160792E09
  1. Disconnect the D41 D-CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-4 (EFI) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher
    D41-15 (EFI) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
Go to step 15
OK


12.CHECK CAN BUS LINE FOR SHORT TO GND (D-CAN J/C - BRAKE ACTUATOR (SKID CONTROL ECU))

NOTICE:
For vehicles without ABS, go to step 13.



    E160792E10
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-1 (ABS) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher
    D41-12 (ABS) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
Go to step 16
OK


13.CHECK CAN BUS LINE FOR SHORT TO GND (D-CAN J/C - AIR CONDITIONING AMPLIFIER)

NOTICE:
For vehicles without air conditioning, go to step 14.



    E160792E11
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-6 (A/C) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher
    D41-17 (A/C) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
Go to step 17
OK


14.CHECK CAN BUS LINE FOR SHORT TO GND (D-CAN J/C - CENTER AIRBAG SENSOR ASSEMBLY)


    E160792E12
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-8 (A/B) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher
    D41-19 (A/B) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
Go to step 18
OK

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (D-CAN J/C - P-CAN J/C (CAN-H, CAN-L)) 

15.CHECK CAN BUS LINE FOR SHORT TO GND (ECM MAIN WIRE)


    C125895E24
  1. Disconnect the A21 ECM connector.



    E160792E09
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-4 (EFI) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher
    D41-15 (EFI) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher

    Result 
    Result
    Proceed to
    NG
    A
    OK (for 1NZ-FE)
    B
    OK (for 2NZ-FE)
    C



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CAN-H, CAN-L) 

16.CHECK CAN BUS LINE FOR SHORT TO GND (BRAKE ACTUATOR (SKID CONTROL ECU) BRANCH WIRE)


  1. for Hatchback:



      C168930E14
    1. Disconnect the A15 brake actuator (skid control ECU) connector.



    2. E160792E10
    3. Measure the resistance according to the value(s) in the table below.

      HINT:
      The resistance must be measured after the D41 D-CAN junction connector is disconnected.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      D41-1 (ABS) - D15-4 (CG)
      Ignition switch off
      200 Ω or higher
      D41-12 (ABS) - D15-4 (CG)
      Ignition switch off
      200 Ω or higher



  1. for Sedan:



      C118165E31
    1. Disconnect the A15 brake actuator (skid control ECU) connector.



    2. E160792E10
    3. Measure the resistance according to the value(s) in the table below.

      HINT:
      The resistance must be measured after the D41 D-CAN junction connector is disconnected.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      D41-1 (ABS) - D15-4 (CG)
      Ignition switch off
      200 Ω or higher
      D41-12 (ABS) - D15-4 (CG)
      Ignition switch off
      200 Ω or higher

      Result 
      Result
      Proceed to
      NG
      A
      OK (for Sedan)
      B
      OK (for Hatchback)
      C



B
REPLACE BRAKE ACTUATOR (SKID CONTROL ECU) (Click here)

C
REPLACE BRAKE ACTUATOR (SKID CONTROL ECU) (Click here)
A

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BRAKE ACTUATOR (SKID CONTROL ECU) (CAN-H, CAN-L) 

17.CHECK CAN BUS LINE FOR SHORT TO GND (AIR CONDITIONING AMPLIFIER BRANCH WIRE)


    C105175E16
  1. Disconnect the E8 air conditioning amplifier connector



    E160792E11
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-6 (A/C) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher
    D41-17 (A/C) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER (CAN-H, CAN-L)
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)  

18.CHECK CAN BUS LINE FOR SHORT TO GND (CENTER AIRBAG SENSOR ASSEMBLY BRANCH WIRE)


    C131069E26
  1. Disconnect the D16 center airbag sensor assembly connector.



    E160792E12
  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    The resistance must be measured after the D41 D-CAN junction connector is disconnected.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D41-8 (A/B) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher
    D41-19 (A/B) - D15-4 (CG)
    Ignition switch off
    200 Ω or higher

    Result 
    Result
    Proceed to
    NG
    A
    OK (for Sedan)
    B
    OK (for Hatchback)
    C



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
A

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CAN-H, CAN-L)