VEHICLE STABILITY CONTROL SYSTEM (for Built-in Type Yaw Rate Sensor) > Brake Warning Light Remains ON |

| 1.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED |
Check if the skid control ECU connector is securely connected.
|
| ||||
| OK | |
| 2.CHECK CAN COMMUNICATION SYSTEM |
Check if CAN communication system DTCs are output (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | |
| 3.INSPECT BATTERY |
Check the battery voltage.
| Result | Proceed to |
| OK | A |
| NG (for 1NZ-FE) | B |
| NG (for 2NZ-FE) | C |
|
| ||||
|
| ||||
| A | |
| 4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL) |
Disconnect the skid control ECU (brake actuator assembly) connector.
Turn the ignition switch to ON.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A54-34 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Skid control ECU) |
Turn the ignition switch off.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A54-1 (GND1) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Skid control ECU) |
Reconnect the skid control ECU (brake actuator assembly) connector.
|
| ||||
| OK | |
| 6.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Parking Brake SW | Parking brake switch/OFF or ON | OFF: Parking brake released ON: Parking brake applied | - |
Using the intelligent tester, check the input of the switch operation when the parking brake pedal is operated.
|
| ||||
| OK | |
| 7.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH) |
![]() |
Turn the ignition switch off.
Remove the reservoir filler cap and strainer.
Disconnect the brake fluid level warning switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - 2 | Switch off (Float up) | 10 kΩ or higher |
| Switch on (Float down) | Below 1 Ω |
| *a | Component without harness connected (Brake Fluid Level Warning Switch) |
Reconnect the brake fluid level warning switch connector.
Reinstall the reservoir filler cap and strainer.
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH) |
Disconnect the combination meter assembly connector and the brake fluid level warning switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F1-12 (SW) - A25-1 (+) | Always | Below 1 Ω |
| A25-2 (E) - Body ground | Always | Below 1 Ω |
| F1-12 (SW) - Body ground | Always | 10 kΩ or higher |
Reconnect the combination meter assembly connector and the brake fluid level warning switch.
|
| ||||
| OK | |
| 9.READ VALUE USING INTELLIGENT TESTER (BRAKE WARNING LIGHT) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Brake Warning Light | Brake warning light/OFF or ON | OFF: Warning light off ON: Warning light on | - |
When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data List.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Brake Warning Light | Brake warning light | Warning light OFF/ON | Observe combination meter [Vehicle condition] Vehicle stopped |
| Result | Proceed to | |
| Data List Display | Data List Display when Performing Active Test ON/OFF Operation | |
| ON | Changes between ON and OFF | A |
| Does not change between ON and OFF | B | |
| OFF | Changes between ON and OFF | A |
| Does not change between ON and OFF | B | |
Connect the intelligent tester to the DLC3.
|
| ||||
| A | |
| 10.REPLACE COMBINATION METER ASSEMBLY |
Turn the ignition switch off.
Replace the combination meter assembly (Click here).
| NEXT | |
| 11.CHECK COMBINATION METER ASSEMBLY |
Connect the intelligent tester to the DLC3.
Perform Active Test of the combination meter assembly using the intelligent tester (Click here).
|
| ||||
| OK | ||
| ||
| 12.INSPECT PARKING BRAKE SWITCH ASSEMBLY |
Remove the parking brake switch assembly (Click here).
Inspect the parking brake switch assembly (Click here).
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - PARKING BRAKE SWITCH) |
Disconnect the instrument panel junction block assembly connector and the parking brake switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3A-28 (PKB) - F22-1 | Always | Below 1 Ω |
| 3A-28 (PKB) - Body ground | Always | 10 kΩ or higher |
Reconnect the instrument panel junction block assembly connector and the parking brake switch assembly connector.
|
| ||||
| OK | |
| 14.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Disconnect the instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3A-28 -12 (PKB) | Always | Below 1 Ω |
| 3A-28 - Body ground | Always | 10 kΩ or higher |
Reconnect the instrument panel junction block assembly connector.
Reinstall the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.
|
| ||||
| OK | ||
| ||