Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > Driver Side Seat Belt Warning Light does not Operate

for Preparation Click here


DESCRIPTION

When the ignition switch is turned to ON, the main body ECU (multiplex network body ECU) transmits front seat inner belt LH*1 (or RH*2) state signals to the combination meter through the CAN. If the driver seat belt is not fastened, the combination meter blinks the front seat belt warning light. If the seat belt is fastened, the warning light goes off.
  1. *1: for LHD
  2. *2: for RHD

WIRING DIAGRAM


B272346E03


INSPECTION PROCEDURE

NOTICE:
Since the seat belt warning system has functions that use CAN communication, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with How to Proceed with Troubleshooting. Then conduct the following troubleshooting procedure.
Initialization is necessary when the main body ECU is replaced (Click here).

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DRIVER SIDE SEAT BELT WARNING LIGHT)
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check that the driver side seat belt warning light turns on/off (Click here).

    Combination Meter 
    Item
    Test Part
    Control Range
    Diagnostic Note
    Driver Side Seat Belt
    Driver side seat belt warning light
    OFF/ON
    Confirm that the vehicle is stopped and the engine is idling.

    OK:
    Driver side seat belt warning light condition can be switched by Active Test.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (DRIVER SIDE SEAT BELT BUCKLE SWITCH)
  1. Check the Data List for proper functioning of the driver side seat belt buckle switch (Click here).

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Seat Buckle SW
    Driver side seat belt buckle signal / OFF or ON
    OFF: Driver side seat belt unfastened
    ON: Driver side seat belt fastened
    -

    OK:
    The display is as specified in the normal condition column.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)  

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER SIDE)
  1. Remove the front seat inner belt assembly (Driver Side) (Click here).

  1. Inspect the front seat inner belt assembly (Driver Side) (Click here).



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
  1. Disconnect the K8*1 or K9*2 front seat inner belt assembly connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Disconnect the 3D instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    3D-34 - K8-3
    Always
    Below 1 Ω
    K8-2 - Body ground
    Always
    Below 1 Ω
    3D-34 - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    3D-34 - K9-3
    Always
    Below 1 Ω
    K9-2 - Body ground
    Always
    Below 1 Ω
    3D-34 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
  1. Replace the main body ECU (Click here).


NEXT


6.READ VALUE USING INTELLIGENT TESTER (DRIVER SIDE SEAT BELT BUCKLE SWITCH)
  1. Check the Data List for proper functioning of the driver side seat belt buckle switch (Click here).

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Seat Buckle SW
    Driver side seat belt buckle signal / OFF or ON
    OFF: Driver side seat belt unfastened
    ON: Driver side seat belt fastened
    -

    OK:
    The display is as specified in the normal condition column.



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK


7.PROCEED TO NEXT INSPECTION PROCEDURE SHOWN IN PROBLEM SYMPTOMS TABLE (FRONT PASSENGER SIDE SEAT BELT WARNING LIGHT MALFUNCTION)
  1. Proceed to "Front Passenger Side Seat Belt Warning Light Malfunction".
    Result 
    Result
    Proceed to
    w/o Front Passenger Side Seat Belt Warning Light Function
    A
    w/ Front Passenger Side Seat Belt Warning Light Function
    B



B
GO TO FRONT PASSENGER SIDE SEAT BELT WARNING LIGHT MALFUNCTION (Click here)
A

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)