Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > Front Passenger Side Seat Belt Warning Light Malfunction

for Preparation Click here


DESCRIPTION

The combination meter assembly detects the state of the front seat inner belt (Front Passenger Side) when the front passenger seat is occupied with the ignition switch ON. If the front passenger seat belt is not fastened, the driver side and front passenger side seat belt warning light in the combination meter assembly blinks. If the seat belt is fastened, the warning light goes off.

WIRING DIAGRAM


B289089E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Perform the previous inspection procedure shown in problem symptoms table (Driver Side Seat Belt Warning Light does not Operate) before performing the following inspection procedure (Click here).

1.READ VALUE USING INTELLIGENT TESTER (FRONT PASSENGER SIDE SEAT BELT WARNING LIGHT)
  1. Check the Data List for proper functioning of the front passenger side seat belt buckle switch (Click here).

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P-Seatbelt Buckle SW
    Front passenger side seat belt buckle signal / OFF or ON
    OFF: Front passenger side seat belt unfastened
    ON: Front passenger side seat belt fastened
    -

    OK:
    ON or OFF appears on the tester screen according to the front passenger side seat belt condition.



NG
Go to step 2
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - IG CIRCUIT)


    E219772E12
  1. Disconnect the combination meter assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F1-39 (IG+) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT SEPARATE TYPE FRONT SEAT CUSHION COVER (OCCUPANT DETECTION SENSOR)
  1. Remove the separate type front seat cushion cover (occupant detection sensor) (Click here).

  1. Inspect the separate type front seat cushion cover (occupant detection sensor) (Click here).



NG
REPLACE SEPARATE TYPE FRONT SEAT CUSHION COVER (OCCUPANT DETECTION SENSOR) (Click here)
OK


4.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR FRONT PASSENGER SIDE)
  1. Remove the front seat inner belt assembly (Front Passenger Side) (Click here).

  1. Inspect the front seat inner belt assembly (Front Passenger Side) (Click here).



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY - COMBINATION METER ASSEMBLY)
  1. Disconnect the front seat inner belt assembly (Front Passenger Side) connector.

  1. Disconnect the combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    F1-7 (P/SB) - K9-3
    Always
    Below 1 Ω
    K9-2 - Body ground
    Always
    Below 1 Ω
    F1-7 (P/SB) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    F1-7 (P/SB) - K8-3
    Always
    Below 1 Ω
    K8-2 - Body ground
    Always
    Below 1 Ω
    F1-7 (P/SB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)