Home › Engine / Hybrid System › 1GR-FE INTAKE / EXHAUST › EXHAUST MANIFOLD › from 2014.08
RM1440E _51 Engine / Hybrid System _056128 1GR-FE INTAKE / EXHAUST _0273907 EXHAUST MANIFOLD A

1GR-FE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 89467B 1.INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

Hide 17105 2.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

a.
A388857E01
1.5,0.927 1.667,0.927 1.667,0.927 1.958,1.156 true 1.323,0.854 1.49,1.052 0.167,0.198 10 false *1

Install a new gasket onto the cylinder head.

Text in Illustration
*1 Protrusion
V100135

Front

NOTICE:

Be careful of the installation direction.



b.

Temporarily install the exhaust manifold sub-assembly LH with 6 new nuts.


c.
A388858E01
0.375,0.219 0.531,0.417 0.156,0.198 10 false 1 1.615,0.271 1.771,0.469 0.156,0.198 10 false 2 2.438,0.365 2.594,0.563 0.156,0.198 10 false 3 2.26,1.552 2.417,1.75 0.156,0.198 10 false 4 1.5,1.677 1.656,1.875 0.156,0.198 10 false 5 0.521,1.531 0.677,1.729 0.156,0.198 10 false 6

Tighten the 6 nuts in the sequence shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Connect the air fuel ratio sensor connector.


Hide 17168 3.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 2 exhaust manifold heat insulator with the 3 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 17362 4.INSTALL NO. 2 AIR TUBE (w/ Secondary Air Injection System)

Hide 17118 5.INSTALL MANIFOLD STAY

a.

Install the manifold stay with the 3 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 89467B 6.INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

Hide 17104 7.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

a.
A388869E01
0.521,1.021 0.823,0.635 0.823,0.635 1.094,0.635 true 1.115,0.542 1.427,0.74 0.313,0.198 10 false *1

Install a new gasket onto the cylinder head.

Text in Illustration
*1 Protrusion
V100135

Front

NOTICE:

Be careful of the installation direction.



b.

Temporarily install the exhaust manifold sub-assembly RH with 6 new nuts.


c.
A388870E01
1.667,0.271 1.823,0.469 0.156,0.198 10 false 1 2.5,0.229 2.656,0.427 0.156,0.198 10 false 2 3.135,1.49 3.292,1.688 0.156,0.198 10 false 3 2.563,1.802 2.719,2 0.156,0.198 10 false 4 1.948,1.74 2.104,1.938 0.156,0.198 10 false 5 1.302,1.771 1.458,1.969 0.156,0.198 10 false 6

Tighten the 6 nuts in the sequence shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Connect the air fuel ratio sensor connector.


Hide 17167 8.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator with the 3 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 17361 9.INSTALL AIR TUBE (w/ Secondary Air Injection System)

Hide 17119 10.INSTALL NO. 2 MANIFOLD STAY

a.

Install the No. 2 manifold stay with the 3 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 17410 11.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Install the front exhaust pipe assembly (See page Engine / Hybrid System>1GR-FE INTAKE / EXHAUST>EXHAUST PIPE>INSTALLATION).


Hide 53737B 17.INSTALL FRONT FENDER APRON SEAL LH

a.

Install the front fender apron seal LH with the 5 clips.


Hide 53736 18.INSTALL FRONT FENDER APRON SEAL RH

a.

Install the front fender apron seal RH with the 4 clips.


Hide 53737A 19.INSTALL FRONT NO. 1 FENDER APRON TO FRAME SEAL LH

a.

Install the front No. 1 fender apron to frame seal LH with the 5 clips.


Hide 53736B 20.INSTALL FRONT NO. 1 FENDER APRON TO FRAME SEAL RH

a.

Install the front No. 1 fender apron to frame seal RH with the 5 clips.