Home › Engine / Hybrid System › 1GR-FE COOLING › RADIATOR › from 2013.08
RM1440E _51 Engine / Hybrid System _056129 1GR-FE COOLING _0273913 RADIATOR A

1GR-FE COOLING  RADIATOR  REMOVAL  


PROCEDURE

Hide 53298 2.REMOVE COOL AIR INTAKE DUCT (for 4WD with TOYOTA Parking Assist-sensor System)

Hide 52129B 3.REMOVE FRONT BUMPER LOWER COVER (w/o TOYOTA Parking Assist-sensor System)

Hide 52129B 4.REMOVE FRONT BUMPER LOWER COVER (w/ TOYOTA Parking Assist-sensor System)

Hide 52822 5.REMOVE AIR INTAKE DUCT LH (w/ TOYOTA Parking Assist-sensor System)

Hide 52821 6.REMOVE AIR INTAKE DUCT RH (w/ TOYOTA Parking Assist-sensor System)

Hide 51405A 7.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 52119A 10.REMOVE FRONT BUMPER COVER

Hide 52521 11.REMOVE UPPER CENTER FRONT BUMPER RETAINER

a.
A311025

Remove the 3 bolts, 2 screws and upper center front bumper retainer.

Text in Illustration
V100135

Bolt
V100136

Nut


Hide 53293C 12.REMOVE RADIATOR SIDE DEFLECTOR RH

a.
A311026

Using a clip remover, detach the 3 claws and remove the clip. Then move the radiator side deflector RH so that the radiator can be removed in the step below.


Hide 53294C 13.REMOVE RADIATOR SIDE DEFLECTOR LH

a.
A311027

Using a clip remover, detach the 3 claws and remove the clip. Then move the radiator side deflector LH so that the radiator can be removed in the step below.


Hide 16571 14.REMOVE NO. 1 RADIATOR HOSE

a.
A223076

Loosen the 2 clamps and remove the No. 1 radiator hose.


Hide 16572 15.REMOVE NO. 2 RADIATOR HOSE

a.
A223077

Loosen the clamp and disconnect the No. 2 radiator hose from the water inlet.


b.
A223078

Detach the clamp from the fan shroud.


c.

Loosen the clamp and remove the No. 2 radiator hose.


Hide 16470 16.REMOVE RADIATOR RESERVOIR TANK

a.
A223079

Disconnect the reservoir hose from the upper side of the radiator tank.


b.

Remove the 3 bolts and radiator reservoir.


Hide 32907C 17.DISCONNECT OIL COOLER TUBE

a.
A223080

Detach the claw to open the flexible hose clamp, and then remove the 2 bolts to disconnect the oil cooler tube from the fan shroud.


Hide 16711 18.REMOVE FAN SHROUD

a.
A223082

Loosen the 4 nuts holding the fan with fluid coupling.


b.

Remove the fan with fluid coupling and generator V-belt (See page Engine / Hybrid System>1GR-FE ENGINE MECHANICAL>DRIVE BELT>REMOVAL).


c.
A223083

Remove the 2 bolts holding the fan shroud.


d.

Remove the 4 nuts of the fan with fluid coupling, and then remove the shroud together with the fan with fluid coupling.

NOTICE:

Be careful not to damage the radiator core.



e.

Remove the fan pulley from the water pump.


Hide 16400 19.REMOVE RADIATOR ASSEMBLY

a.
A224905

Slide the 2 clamps and disconnect the 2 oil cooler hoses.


b.
A224957

Remove the 4 bolts and radiator.


Hide 16561 20.REMOVE NO. 1 RADIATOR TO SUPPORT SEAL

a.

Remove the No. 1 radiator to support seal from the radiator assembly.


Hide 16562 21.REMOVE NO. 2 RADIATOR TO SUPPORT SEAL

a.

Remove the No. 2 radiator to support seal from the radiator assembly.