Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2009.08–2013.08
RM1440E _57 Power Source / Network _056154 NETWORKING _0274053 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Open in One Side of CAN Branch Line  


DESCRIPTION

If 2 or more ECUs and/or sensors do not appear on the intelligent tester "CAN Bus Check" screen, one side of the CAN branch wire may be open (one side of the CANH [branch wire]/CANL [branch wire] of the ECU and/or sensor is open).

Symptom Trouble Area
2 or more ECUs and/or sensors do not appear on the intelligent tester "Bus Check" screen.
·

Master cylinder solenoid (skid control ECU)

·

Four wheel drive control ECU*

·

Yaw rate sensor assembly

·

Spiral cable sub-assembly (steering angle sensor)

·

Power steering ECU assembly

·

Air conditioning amplifier assembly

·

Center airbag sensor assembly

·

Main body ECU (multiplex network body ECU)



*: for 4WD


WIRING DIAGRAM

C213055E02
5.958,0.406 6.385,0.563 0.427,0.156 10 false CANH 0.865,0.479 1.292,0.667 0.427,0.188 10 false CANH 0.865,0.906 1.292,1.094 0.427,0.188 10 false CANL 4.01,0.385 4.146,0.531 0.135,0.146 10 false 3 4.01,0.844 4.146,0.99 0.135,0.146 10 false 6 5.76,0.385 5.875,0.531 0.115,0.146 10 false 1 5.76,0.844 5.875,0.99 0.115,0.146 10 false 2 4.01,1.219 4.146,1.365 0.135,0.146 10 false 2 4.01,1.667 4.146,1.813 0.135,0.146 10 false 5 1.365,0.385 1.552,0.531 0.188,0.146 10 false 11 1.365,0.844 1.552,0.99 0.188,0.146 10 false 25 3.25,0.385 3.385,0.531 0.135,0.146 10 false 1 3.25,0.844 3.365,0.99 0.115,0.146 10 false 4 0.854,2.771 1.281,2.958 0.427,0.188 10 false CANH 0.854,3.167 1.281,3.354 0.427,0.188 10 false CANL 0.854,4.771 1.281,4.958 0.427,0.188 10 false CANH 0.875,5.198 1.271,5.385 0.396,0.188 10 false CANL 5.969,4.771 6.396,4.958 0.427,0.188 10 false CANH 5.969,5.198 6.365,5.385 0.396,0.188 10 false CANL 0.854,6.708 1.281,6.896 0.427,0.188 10 false CANH 0.854,7.135 1.281,7.323 0.427,0.188 10 false CANL 4.01,2.677 4.198,2.823 0.188,0.146 10 false 3 4.01,3.094 4.198,3.24 0.188,0.146 10 false 14 4.01,4.677 4.198,4.823 0.188,0.146 10 false 5 4.01,5.104 4.198,5.25 0.188,0.146 10 false 16 4.01,6.646 4.198,6.792 0.188,0.146 10 false 1 4.01,7.063 4.198,7.208 0.188,0.146 10 false 12 1.365,2.677 1.552,2.823 0.188,0.146 10 false 14 1.365,3.104 1.552,3.25 0.188,0.146 10 false 13 3.281,2.667 3.417,2.813 0.135,0.146 10 false 2 3.177,3.104 3.365,3.25 0.188,0.146 10 false 13 3.281,4.677 3.417,4.823 0.135,0.146 10 false 4 3.177,5.104 3.365,5.25 0.188,0.146 10 false 15 5.667,4.677 5.875,4.823 0.208,0.146 10 false 13 5.667,5.104 5.854,5.25 0.188,0.146 10 false 22 1.365,4.677 1.5,4.823 0.135,0.146 10 false 6 1.365,5.104 1.552,5.25 0.188,0.146 10 false 14 1.365,6.625 1.5,6.771 0.135,0.146 10 false 4 1.365,7.063 1.552,7.208 0.188,0.146 10 false 3 3.281,6.635 3.417,6.781 0.135,0.146 10 false 7 3.177,7.073 3.365,7.219 0.188,0.146 10 false 18 5.958,1.073 6.385,1.219 0.427,0.146 10 false CANL 5.698,1.302 5.99,1.469 0.292,0.167 10 false F14 5.698,1.458 6.906,1.813 1.208,0.354 10 false Combination Meter Assembly 5.656,5.604 6.01,5.76 0.354,0.156 10 false F33 5.656,5.76 6.99,6.115 1.333,0.354 10 false Center Airbag Sensor Assembly 2.854,7.635 4.427,7.823 1.573,0.188 10 false No. 2 Junction Connector 2.854,7.479 3.146,7.646 0.292,0.167 10 false F59 2.854,2.042 3.208,2.229 0.354,0.188 10 false A36 2.854,2.208 4.49,2.396 1.635,0.188 10 false No. 1 Junction Connector 0.24,1.313 0.594,1.5 0.354,0.188 10 false A6 0.24,1.49 1.833,1.865 1.594,0.375 10 false Master Cylinder Solenoid (Skid Control ECU) 0.156,3.542 0.51,3.729 0.354,0.188 10 false F9 0.156,3.698 1.833,4.073 1.677,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 0.729,5.615 1.052,5.781 0.323,0.167 10 false F13 0.125,7.563 0.448,7.729 0.323,0.167 10 false F19 0.729,5.781 1.146,5.948 0.417,0.167 10 false DLC3 0.125,7.74 1.802,8.104 1.677,0.365 10 false Spiral Cable Sub-assembly (Steering Angle Sensor)

C213056E02
5.958,3.917 6.385,4.073 0.427,0.156 10 false CANH 5.698,3.917 5.885,4.063 0.188,0.146 10 false 32 5.698,4.365 5.885,4.51 0.188,0.146 10 false 31 0.854,0.375 1.281,0.563 0.427,0.188 10 false CANH 0.854,0.792 1.281,0.979 0.427,0.188 10 false CANL 5.948,2.208 6.375,2.396 0.427,0.188 10 false CANH 5.948,2.635 6.375,2.823 0.427,0.188 10 false CANL 0.854,2.198 1.281,2.385 0.427,0.188 10 false CANH 0.854,2.625 1.281,2.813 0.427,0.188 10 false CANL 0.854,4 1.281,4.188 0.427,0.188 10 false CANH 1.344,3.896 1.677,4.052 0.333,0.156 10 false 11 0.885,4.438 1.281,4.625 0.396,0.188 10 false CANL 4.01,0.281 4.198,0.427 0.188,0.146 10 false 1 4.01,0.708 4.198,0.854 0.188,0.146 10 false 12 4.01,2.135 4.198,2.281 0.188,0.146 10 false 5 4.01,2.552 4.198,2.698 0.188,0.146 10 false 16 1.365,2.135 1.49,2.281 0.125,0.146 10 false 3 1.365,2.552 1.49,2.698 0.125,0.146 10 false 2 3.281,0.281 3.417,0.427 0.135,0.146 10 false 3 3.177,0.708 3.365,0.854 0.188,0.146 10 false 14 1.365,0.281 1.563,0.427 0.198,0.146 10 false 19 1.365,0.708 1.552,0.854 0.188,0.146 10 false 20 5.781,2.115 5.917,2.26 0.135,0.146 10 false 1 5.781,2.552 5.875,2.698 0.094,0.146 10 false 2 3.281,2.125 3.417,2.271 0.135,0.146 10 false 7 3.177,2.563 3.365,2.708 0.188,0.146 10 false 18 3.281,3.927 3.417,4.073 0.135,0.146 10 false 8 3.177,4.385 3.365,4.531 0.188,0.146 10 false 19 5.958,4.573 6.385,4.719 0.427,0.146 10 false CANL 6.125,4.854 6.479,5.031 0.354,0.177 10 false F50 6.125,5.01 6.479,5.188 0.354,0.177 10 false ECM 2.875,4.802 3.229,4.99 0.354,0.188 10 false F60 2.875,4.979 4.51,5.167 1.635,0.188 10 false No. 3 Junction Connector 0.063,4.802 0.396,4.979 0.333,0.177 10 false F42 0.063,4.958 2.323,5.135 2.26,0.177 10 false Air Conditioning Amplifier Assembly 0.073,1.146 0.469,1.313 0.396,0.167 10 false F47 0.073,1.313 2.125,1.479 2.052,0.167 10 false Four Wheel Drive Control ECU* 5.656,2.969 6.052,3.135 0.396,0.167 10 false F41 5.656,3.135 6.99,3.479 1.333,0.344 10 false Power Steering ECU Assembly 0.083,2.969 0.479,3.135 0.396,0.167 10 false F36 0.083,3.135 1.854,3.323 1.771,0.188 10 false Yaw Rate Sensor Assembly 4.01,3.917 4.198,4.063 0.188,0.146 10 false 2 4.01,4.385 4.198,4.531 0.188,0.146 10 false 13 0.135,5.438 0.927,5.625 0.792,0.188 10 false *: for 4WD 1.344,4.354 1.677,4.51 0.333,0.156 10 false 12

CAUTION / NOTICE / HINT

HINT:
·

Perform the following inspection for the ECUs (sensors) which are not displayed on the intelligent tester If a malfunction cannot be identified, perform the following inspections for the ECUs (sensors) connected to the CAN communication system.


·

Do not remove the combination meter assembly and ECM, as they are the end parts of the circuit. If removed, CAN communication is not possible.


·

The open circuit confirmation of the combination meter assembly, ECM and main wire is performed in the Check CAN Bus Line procedure of "How to Proceed with Troubleshooting". This inspection only has procedures for checking for an open circuit on one side of the CAN branch wire.



PROCEDURE

1.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MASTER CYLINDER SOLENOID)
a.

Disconnect the A6 master cylinder solenoid (skid control ECU) connector.


b.

Select "Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"ABS/VSC/TRC" not displayed on the intelligent tester A
Several ECUs and sensors in addition to "ABS/VSC/TRAC" not displayed on the intelligent tester B



A

2.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MASTER CYLINDER SOLENOID BRANCH WIRE)

B

3.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU)
2.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MASTER CYLINDER SOLENOID BRANCH WIRE)
a.
U180827E01
0.073,0.08 0.270,0.266 0.197,0.186 10 *a 1.595,0.663 1.808,0.849 0.213,0.186 10 A6 2.493,0.813 2.933,0.999 0.440,0.186 10 CANH 2.864,1.077 3.262,1.246 0.398,0.169 10 CANL 2.207,1.77 2.36,0.902 2.36,0.902 2.465,0.902 false 2.207,1.896 2.765,1.162 2.765,1.162 2.843,1.162 false

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A6-11 (CANH) - A6-25 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])



OK

REPLACE MASTER CYLINDER SOLENOID

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (MASTER CYLINDER SOLENOID)

3.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU)
a.

Disconnect the F9 main body ECU (multiplex network body ECU) connector.


b.

Select "Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Main Body" not displayed on the intelligent tester A
Several ECUs and sensors in addition to "Main Body" not displayed on the intelligent tester B



A

4.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU BRANCH WIRE)

B

5.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR)
4.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU BRANCH WIRE)
a.
U180838E02
1.281,0.458 1.375,0.458 1.375,0.458 1.615,1.177 true 1.542,1.188 1.052,0.708 1.052,0.708 0.969,0.708 true 0.063,0.063 0.302,0.25 0.24,0.188 10 false *a 0.521,0.635 0.948,0.792 0.427,0.156 10 false CANH 0.865,0.385 1.271,0.542 0.406,0.156 10 false CANL 0.51,1.115 0.75,1.271 0.24,0.156 10 false F9

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION)



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F9-14 (CANH) - F9-13 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (MAIN BODY ECU)

5.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR)
a.

Disconnect the F36 yaw rate sensor assembly connector.


b.

Select "Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Yaw Rate / Deceleration Sensor" not displayed on the intelligent tester A
Several ECUs and sensors in addition to "Yaw Rate / Deceleration Sensor" not displayed on the intelligent tester B



A

6.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR BRANCH WIRE)

B

7.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SPIRAL CABLE)
6.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR BRANCH WIRE)
a.
U180829E02
0.906,0.979 1,0.979 1,0.979 1.427,1.438 true 1.177,0.563 1.292,0.563 1.292,0.563 1.573,1.448 true 0.052,0.031 0.229,0.208 0.177,0.177 10 false *a 0.458,0.927 0.865,1.104 0.406,0.177 10 false CANL 0.438,1.448 0.74,1.625 0.302,0.177 10 false F36 0.719,0.49 1.146,0.667 0.427,0.177 10 false CANH

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F36-3 (CANH) - F36-2 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (YAW RATE SENSOR)

7.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SPIRAL CABLE)
a.

Disconnect the F19 spiral cable sub-assembly (steering angle sensor) connector.


b.

Select "Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Steering Angle Sensor" not displayed on the intelligent tester A
Several ECUs and sensors in addition to "Steering Angle Sensor" not displayed on the intelligent tester B



A

8.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SPIRAL CABLE BRANCH WIRE)

B

9.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU)
8.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SPIRAL CABLE BRANCH WIRE)
a.
U180817E02
2.042,1.531 1.729,1.052 1.729,1.052 1.656,1.052 true 2.146,1.521 2.396,1.26 2.396,1.26 2.552,1.26 true 1.198,0.99 1.625,1.188 0.427,0.198 10 false CANH 1.219,1.396 1.542,1.594 0.323,0.198 10 false F19 0.094,0.073 0.323,0.26 0.229,0.188 10 false *a 2.625,1.188 3.042,1.385 0.417,0.198 10 false CANL

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F19-4 (CANH) - F19-3 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Spiral Cable Sub-assembly [Steering Angle Sensor])



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (SPIRAL CABLE)

9.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU)
a.

Disconnect the F41 power steering ECU assembly connector.


b.

Select "Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"PPS" not displayed on the intelligent tester A
Several ECUs and sensors in addition to "PPS" not displayed on the intelligent tester B



A

10.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU BRANCH WIRE)

B

11.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER)
10.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU BRANCH WIRE)
a.
U180836E02
1.917,1.51 2.135,1.052 2.135,1.052 2.229,1.052 true 2.375,1.24 2.302,1.24 2.302,1.24 2.031,1.51 true 0.063,0.052 0.281,0.25 0.219,0.198 10 false *a 2.438,1.177 2.865,1.344 0.427,0.167 10 false CANH 2.281,0.969 2.698,1.135 0.417,0.167 10 false CANL 0.677,1.333 1,1.5 0.323,0.167 10 false F41

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F41-1 (CANH) - F41-2 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (POWER STEERING ECU)

11.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER)
a.

Disconnect the F42 air conditioning amplifier assembly connector.


b.

Select "Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Air Conditioner" not displayed on the intelligent tester A
Several ECUs and sensors in addition to "Air Conditioner" not displayed on the intelligent tester B



A

12.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER BRANCH WIRE)

B

13.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (FOUR WHEEL DRIVE CONTROL ECU)
12.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER BRANCH WIRE)
a.
U180888E02
2.135,1.063 1.875,0.115 1.875,0.115 1.74,0.115 true 1.99,1.052 1.594,0.292 1.594,0.292 1.469,0.292 true 0.052,0.083 0.229,0.292 0.177,0.208 10 false *a 0.51,1 0.823,1.177 0.313,0.177 10 false F42 1.323,0.042 1.76,0.208 0.438,0.167 10 false CANH 1.052,0.219 1.427,0.396 0.375,0.177 10 false CANL

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F42-11 (CANH) - F42-12 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (AIR CONDITIONING AMPLIFIER)

13.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (FOUR WHEEL DRIVE CONTROL ECU)
HINT:

For vehicles without a four wheel drive, go to "Check for Open in One Side of CAN Branch Wire (Center Airbag Sensor)".


a.

Disconnect the F47 four wheel drive ECU connector.


b.

Select "Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Four Wheel Drive Control" not displayed on the intelligent tester A
Several ECUs and sensors in addition to "Four Wheel Drive Control" not displayed on the intelligent tester B



A

14.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (FOUR WHEEL DRIVE CONTROL ECU BRANCH WIRE)

B

15.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR BRANCH WIRE)
14.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (FOUR WHEEL DRIVE CONTROL ECU BRANCH WIRE)
a.
U180841E02
0.479,1.01 0.563,1.01 0.563,1.01 0.677,1.344 true 0.594,0.708 0.688,0.708 0.688,0.708 0.76,1.354 true 0.063,0.021 0.229,0.208 0.167,0.188 10 false *a 0.146,0.646 0.552,0.802 0.406,0.156 10 false CANH 0.083,0.948 0.458,1.115 0.375,0.167 10 false CANL 2.438,1.24 2.74,1.396 0.302,0.156 10 false F47

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F47-19 (CANH) - F47-20 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Four Wheel Drive Control ECU)



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU NO.2

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU)

15.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR BRANCH WIRE)
a.
U180822E02
1.302,1.146 0.729,1.417 0.729,1.417 0.656,1.417 true 1.177,1.49 0.948,1.865 0.948,1.865 0.823,1.865 true 0.063,0.052 0.25,0.229 0.188,0.177 10 false *a 0.208,1.344 0.625,1.521 0.417,0.177 10 false CANH 0.281,1.021 0.594,1.198 0.313,0.177 10 false F33 0.396,1.802 0.792,1.969 0.396,0.167 10 false CANL

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the F33 center airbag sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F33-13 (CANH) - F33-22 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Center Airbag Sensor Assembly)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CENTER AIRBAG SENSOR)