1. TABLE OF BOLT, SCREW AND NUT
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
84140
3.REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY
58910C
4.REMOVE REAR CONSOLE BOX ASSEMBLY
67920
5.REMOVE DOOR SCUFF PLATE ASSEMBLY LH
67910
6.REMOVE DOOR SCUFF PLATE ASSEMBLY RH
Use the same procedure as for the LH side.
62112
7.REMOVE COWL SIDE TRIM BOARD LH
62111C
8.REMOVE COWL SIDE TRIM BOARD RH
Use the same procedure as for the LH side.
62312B
9.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62311B
10.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
74617A
11.REMOVE ASSIST GRIP PLUG
74611F
12.REMOVE NO. 1 ASSIST GRIP
62211
13.REMOVE FRONT PILLAR GARNISH RH
62212
14.REMOVE FRONT PILLAR GARNISH LH
55480D
15.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
Detach the 4 clips.
Disconnect the cooler thermistor and remove the lower instrument panel finish panel assembly.
55447C
16.REMOVE NO. 2 SWITCH HOLE BASE
Detach the 6 clips and 2 guides.
Disconnect each connector and remove the No. 2 switch hole base.
55404D
17.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Detach the 7 clips to remove the instrument cluster finish panel sub-assembly.
83100
18.REMOVE COMBINATION METER ASSEMBLY
55045
19.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
Using a screwdriver, detach the 2 claws to open the cover.
Tape the screwdriver tip before use.
| *1 | Protective Tape |
Remove the 2 bolts <C>.
Detach the 6 clips and 2 guides.
Disconnect each connector and hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.
55607
20.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Detach the 3 clips and 2 guides to remove the No. 2 instrument panel under cover sub-assembly.
55312
21.REMOVE LOWER INSTRUMENT PANEL
Remove the 2 bolts <D>.
Detach the 4 clips to remove the lower instrument panel.
55443A
22.REMOVE INSTRUMENT PANEL BOX DOOR COVER
Using a screwdriver, detach the 2 claws and 2 guides to remove the instrument panel box door cover.
| *1 | Protective Tape |
Tape the screwdriver tip before use.
Use the same procedure for all the instrument panel box door covers.
55303B
23.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
Remove the 3 screws <B> and 2 bolts <C>.
Detach the 10 clips and guide.
Disconnect each connector and remove the lower instrument panel sub-assembly.
55910R
24.REMOVE HEATER CONTROL ASSEMBLY
55424C
25.REMOVE RADIO TUNER FINISH PANEL (w/o Audio)
Remove the 4 bolts.
Pull the radio tuner finish panel towards the rear of the vehicle and detach the 6 clips to remove the radio tuner finish panel.
Disconnect the connector.
86140A
26.REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKETS (w/ Audio)
55406B
27.REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Climate Control Seat System)
Remove the 2 screws <B>.
Detach the 4 clips.
Disconnect each connector and remove the lower center instrument cluster finish panel sub-assembly.
55406B
28.REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/ Climate Control Seat System)
Remove the 2 screws <B>.
Detach the 4 clips.
Disconnect each connector and remove the lower center instrument cluster finish panel sub-assembly.
55650
29.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
Detach the 4 clips and 2 guides to remove the No. 1 instrument panel register assembly.
55660
30.REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
Use the same procedure as for the No. 1 instrument panel register assembly.
55408F
31.REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Put protective tape around the No. 1 instrument panel speaker panel sub-assembly.
Using a screwdriver, detach the 2 clips, 4 claws and 3 guides to remove the No. 1 instrument panel speaker panel sub-assembly.
| *1 | Protective Tape |
Tape the screwdriver tip before use.
55409F
32.REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Put protective tape around the No. 2 instrument panel speaker panel sub-assembly.
Using a screwdriver, detach the 2 clips, 3 claws and 3 guides to remove the No. 2 instrument panel speaker panel sub-assembly.
| *1 | Protective Tape |
Tape the screwdriver tip before use.
86160P
33.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY
89533A
34.REMOVE 4 WHEEL DRIVE CONTROL ECU NO.2 (for 4WD)
55301
35.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
Remove the 6 bolts <E> and nut <F>.
Remove the 2 passenger airbag bolts and bolt labeled A.
Disconnect each connector and detach the clamps and claws.
Detach the 2 guides and remove the instrument panel sub-assembly.
| *1 | Bolt <E> | *2 | Nut <F> |
| *3 | Guide | *4 | Passenger Airbag Bolt |
| *5 | Bolt A | - | - |