Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › from 2013.08
RM1440E _59 Vehicle Exterior _056168 DOOR / HATCH _0274178 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 67492A 2.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

a.
B240255

Detach the 2 clips to remove the front door lower frame bracket garnish LH.


Hide 69298A 3.REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH

a.
B240256E02
1.479,1.823 1.281,1.365 true 1.479,1.865 1.646,2.031 0.167,0.167 10 false *1

Using a moulding remover, detach the 3 claws to remove the No. 2 door inside handle bezel LH as shown in the illustration.

Text in Illustration
*1 Moulding Remover


Hide 67602 4.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B353477

Detach the 4 claws to remove the 2 door armrest caps.


b.
B353478

Remove the 3 screws.


c.

Detach the 11 clips.


d.
B353479E02
0.813,3.938 0.583,3.938 false 2.656,4.229 2.583,3.979 false 0.406,3.844 0.563,3.99 0.156,0.146 10 false *1 2.594,4.25 2.75,4.396 0.156,0.146 10 false *1

Pull out the front door trim board sub-assembly LH in the direction indicated by the arrow shown in the illustration.


e.

Raise the front door trim board sub-assembly LH and detach the 4 claws and reference boss to remove the front door trim board sub-assembly LH together with the front door inner glass weatherstrip LH.

Text in Illustration
*1 Reference Boss


f.
B240574

Disconnect the connector.


g.
B238525

Disconnect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH.


Hide 68172A 5.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH

a.
B238526

Using a screwdriver, detach the 4 claws to remove the front door inner glass weatherstrip LH from the front door trim board sub-assembly LH as shown in the illustration.


Hide 81080J 6.REMOVE NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)

a.
E200689E04
1.135,0.167 1.917,0.771 true 0.948,0.063 1.104,0.24 0.156,0.177 10 false *1

Using a screwdriver, detach the claw and remove the light.

Text in Illustration
*1 Protective Tape

HINT:

Tape the screwdriver tip before use.



b.

Disconnect the connector.


Hide 84040 8.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (for Driver Side)

Hide 84930 9.REMOVE DOOR CONTROL SWITCH ASSEMBLY (for Front Passenger Side)

Hide 84810 10.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

Hide 84927 11.REMOVE SEAT MEMORY SWITCH (w/ Seat Position Memory System)

Hide 86160 12.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

Hide 89860A 13.REMOVE SIDE AIRBAG SENSOR ASSEMBLY LH

Hide 67832 14.REMOVE FRONT DOOR SERVICE HOLE COVER LH

a.
B240582

Remove the bolt.


b.

Detach the 2 clamps and move the front door wire out of the way to remove the front door service hole cover LH.

HINT:

Remove any remaining butyl tape from the door panel.



Hide 87940 15.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 68102 16.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

a.

Connect the multiplex network master switch assembly (for Driver Side).


b.

Connect the power window regulator switch assembly (for Front Passenger Side).


c.

Connect the cable to the negative (-) battery terminal.


d.

Move the front door glass sub-assembly so that the front door glass bolts can be seen.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



f.

Disconnect the multiplex network master switch assembly (for Driver Side).


g.

Disconnect the power window regulator switch assembly (for Front Passenger Side).


h.
B353480

Remove the 2 bolts.

NOTICE:

Be careful when removing the bolts as the glass may fall and become damaged.



i.
B353481E02
0.375,0.375 0.594,0.594 0.219,0.219 10 true (1) 2.083,0.104 2.302,0.302 0.219,0.198 10 false (2)

Remove the front door glass sub-assembly LH as indicated by the arrows in the order shown in the illustration.

NOTICE:

Do not damage the front door glass sub-assembly LH.



Hide 69802 17.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.
B353482E05
1.792,1.135 2,1.135 2,1.135 2.073,1.208 false 1.635,1.042 1.823,1.26 0.188,0.219 10 true *1

Disconnect the connector.


b.

Loosen the temporary bolt.

Text in Illustration
*1 Temporary Bolt

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator sub-assembly LH may fall and cause damage.



c.

Remove the 5 bolts.


d.

Remove the front door window regulator sub-assembly LH.


e.

Remove the temporary bolt from the front door window regulator sub-assembly LH.


Hide 85720C 18.REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 67664C 19.REMOVE DOOR FRAME GARNISH LH

a.
B240607

Detach the clip to remove the door frame garnish LH.


Hide 68151E 20.REMOVE FRONT DOOR GLASS RUN LH

a.
B240586

Remove the front door glass run LH.


Hide 67404F 21.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

a.
B240587

Remove the bolt and front door rear lower frame sub-assembly LH as shown in the illustration.


Hide 22.REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B240588

Remove the hole plug.


b.
B240589

Using a T30 "TORX" socket wrench, loosen the screw to remove the front door outside handle cover with lock cylinder assembly.

HINT:

The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



Hide 69217F 23.REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH (for Driver Side)

a.
B238539

Using a screwdriver, detach the claw to remove the front door outside handle cover LH from the lock cylinder assembly.

HINT:

Tape the screwdriver tip before use.



Hide 69217E 24.REMOVE FRONT DOOR OUTSIDE HANDLE COVER RH (for Front Passenger Side)

a.
B240590

Remove the hole plug.


b.
B240591

Using a T30 "TORX" socket wrench, loosen the screw to remove the front door outside handle cover RH.

HINT:

The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



Hide 69220 25.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B240593

Move the lever in the direction indicated by the arrow in the illustration.


b.
B240594

Remove the front door outside handle assembly LH as shown in the illustration.


Hide 69241H 26.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD LH

a.
B354869

Detach the guide and 2 claws to remove the front door front outside handle pad LH.


Hide 69242F 27.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD LH

a.
B240596

Detach the 2 claws to remove the front door rear outside handle pad LH.


Hide 69040A 28.REMOVE FRONT DOOR LOCK ASSEMBLY LH

Hide 69720B 29.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.
B240599

Remove the front door lock remote control cable assembly LH from the front door lock assembly LH.


Hide 69760C 30.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.
B240600

Using a screwdriver, detach the 3 claws to open the cover.

HINT:

Tape the screwdriver tip before use.



b.
B240601

Remove the front door inside locking cable assembly LH from the front door lock assembly LH.


Hide 69202A 31.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.
B240604

Using a T30 "TORX" socket wrench, loosen the screw.


b.

Slide the front door outside handle frame sub-assembly LH to detach the door handle nut and claw of the front door outside handle frame sub-assembly LH. Then remove the front door outside handle frame sub-assembly LH.


Hide 69312 32.REMOVE FRONT DOOR LOCK OPEN ROD LH

a.
B238554E02
2.927,2.458 3.198,2.74 0.271,0.281 10 false (2) 2.49,1.927 2.76,2.094 0.271,0.167 10 true (1)

Remove the front door lock open rod LH as indicated by the arrows in the order shown in the illustration.


Hide 67924 33.REMOVE FRONT DOOR NO. 2 STIFFENER CUSHION

a.
B238555E03
2.365,1.135 2.125,1.135 2.125,1.135 1.74,0.708 true 2.396,1.063 2.604,1.26 0.208,0.198 10 false *1

Remove the 2 bolts.

Text in Illustration
*1 Double-sided Tape


b.

Detach the 2 clamps to remove the front door No. 2 stiffener cushion.


Hide 68620 34.REMOVE FRONT DOOR CHECK ASSEMBLY LH

a.
B238556

Remove the bolt, 2 nuts and front door check assembly LH.


Hide 67862 35.REMOVE FRONT DOOR WEATHERSTRIP LH

a.
B353483

Using a clip remover, detach the 21 clips to remove the front door weatherstrip LH.


Hide 75756C 37.REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH

Hide 75976G 40.REMOVE FRONT DOOR LOWER OUTSIDE STRIPE LH

Hide 67001A 41.REMOVE FRONT DOOR PANEL CUSHION

a.
B240615

Using a clip remover, detach the claw to remove the front door panel cushion.