Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM

OCCUPANT CLASSIFICATION SYSTEM > Trouble in Passenger Airbag ON/OFF Indicator

for Preparation Click here


DESCRIPTION

The occupant classification system detects the front passenger seat condition. The system then informs the passenger of the front passenger airbag assembly and front passenger side knee airbag status (activated/not activated) with the passenger airbag ON/OFF indicator.

HINT:
Approximately 6 seconds after the ignition switch is turned to ON, the passenger airbag ON/OFF indicator will indicate the on/off status depending on the conditions listed below.

Front Passenger Seat Condition
ON Indicator
OFF Indicator
Vacant
Off
Off
Adult is seated
On
Off
Child is seated
Off
On
Front passenger occupant classification system failure
Off
On


INSPECTION PROCEDURE

1.CHECK SRS WARNING LIGHT
  1. Turn the ignition switch to ON and check the SRS warning light condition.

    HINT:
    If this trouble occurs, the SRS warning light is off. If the light is on, this indicates that a DTC is stored. Troubleshoot for the output DTC.

    OK:
    After the primary check period, the SRS warning light goes off.

    HINT:
    The primary check is performed for approximately 6 seconds after the ignition switch is turned to ON.



NG
GO TO AIRBAG SYSTEM (Click here)
OK


2.PERFORM ZERO POINT CALIBRATION
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.



NG
Go to step 5
OK


3.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)



NG
Go to step 5
OK


4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
  1. Turn the ignition switch to ON.

  1. Check if the passenger airbag ON/OFF indicator correctly indicates the front passenger seat condition.

    OK:

    Front Passenger Seat Condition
    ON Indicator
    OFF Indicator
    Vacant
    Off
    Off
    Adult is seated
    On
    Off
    Child is seated
    Off
    On
    Front passenger occupant classification system failure
    Off
    On



NG
Go to step 5
OK

END 

5.RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT
  1. Turn the ignition switch off.

  1. Loosen the 4 installation bolts of the front seat RH.

  1. for Manual Seat:

    1. Tighten the 4 installation bolts of the front seat RH to the specified torque (Click here).

  1. for Power Seat:

    1. Tighten the 4 installation bolts of the front seat RH to the specified torque (Click here).

Torque:
37 N*m{ 377 kgf*cm , 27 ft.*lbf }


NEXT


6.PERFORM ZERO POINT CALIBRATION
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.



NG
Go to step 8
OK


7.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)



NG
Go to step 8
OK

END 

8.READ VALUE USING TECHSTREAM (FRONT PASSENGER SIDE BUCKLE SWITCH)
  1. Using the Techstream, read the Data List (Click here).

    Occupant Detection 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Passenger Buckle SW
    Front passenger side seat belt buckle switch / Unset, Set or NG
    Unset: Front passenger side seat belt unfastened
    Set: Front passenger side seat belt fastened
    NG: Condition undetermined
    -

    OK:
    The display is as specified in the normal condition column.



NG
Go to step 17
OK


9.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY RH
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. for Manual Seat:

    1. Replace the separate type front seat cushion spring RH (Click here).

  1. for Power Seat:

    1. Replace the separate type front seat cushion spring RH (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.


NEXT


10.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.



NG
Go to step 12
OK


11.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)



NG
Go to step 12
OK

END 

12.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors (on the occupant classification ECU side and occupant classification sensor side) are not damaged (Click here).

    OK:
    Connectors are not deformed or damaged.



NG
REPLACE FRONT SEAT WIRE RH
OK


13.CHECK FOR DTC
  1. Connect the connectors to the occupant classification ECU and 4 occupant detection sensors.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

    HINT:
    1. First clear the DTCs stored in the occupant classification ECU, and then clear the DTCs stored in the center airbag sensor.
    2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC is not output.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK


14.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Connect the connectors to the 4 occupant classification sensors.

  1. Replace the occupant classification ECU (Click here).

HINT:
Perform the inspection using parts from a normal vehicle when possible.


NEXT


15.PERFORM ZERO POINT CALIBRATION
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.


NEXT


16.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)


NEXT

END 

17.CHECK CONNECTOR
  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Turn the ignition switch off.

  1. Disconnect the connectors from the occupant classification ECU and front seat inner belt RH.

  1. Check that the connectors (on the occupant classification ECU side and front seat inner belt RH side) are not damaged (Click here).

    OK:
    Connectors are not deformed or damaged.



NG
REPLACE FRONT SEAT WIRE RH
OK


18.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
  1. Replace the front seat inner belt RH (Click here).


NEXT


19.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, perform the zero point calibration (Click here).

    OK:
    "Zero Point Calibration is complete." is displayed.


NEXT


20.PERFORM SENSITIVITY CHECK
  1. Using the Techstream, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)


NEXT

END