Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL ENGINE HANGER


    A229669E01
  1. Install 2 engine hangers with 4 bolts as shown in the illustration.

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }

    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger

    HINT:
    No. 1 Engine Hanger
    12281-31110
    No. 2 Engine Hanger
    12282-31140
    Bolt
    91671-C0830



2. REMOVE ENGINE STAND
  1. Attach an engine sling device and hang the engine with a chain block.

  1. Lift the engine and remove it from the engine stand.

  1. Place the engine onto a work bench.



3. INSTALL ENGINE ASSEMBLY
  1. Attach an engine sling device and hang the engine with a chain block.

  1. Slowly lower the engine into the engine compartment.



    A225433E01
  1. Install the front engine mounting insulator LH with the 3 nuts and 2 bolts.

    Torque:
    for nut A:
    72 N*m{ 734 kgf*cm , 53 ft.*lbf }
    for nut B:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Install the front engine mounting insulator RH with the 3 nuts and 2 bolts.

    Torque:
    for nut A:
    72 N*m{ 734 kgf*cm , 53 ft.*lbf }
    for nut B:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Remove the 4 bolts and 2 engine hangers.



4. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A227952E01
  1. Install the front spacer, drive plate and ring gear sub-assembly and rear spacer to the crankshaft.
    Text in Illustration 
    *1
    Front Spacer
    *2
    Drive Plate and Ring Gear Sub-assembly
    *3
    Rear Spacer
    V100135
    Automatic Transmission Side

    HINT:
    As the front spacer, drive plate and ring gear sub-assembly and rear spacer are not reversible, be sure to install them in the correct direction as shown in the illustration.

  1. Apply adhesive to 2 or 3 threads at the end of the 8 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



    A224777E01
  1. Uniformly install and tighten the 8 bolts in several steps in the sequence shown in the illustration.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 1 hour after installing.

  1. Tighten the 8 bolts an additional 90°.

    NOTICE:
    Tighten diametrically opposite bolts in pairs.



5. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY
for 2WD: (Click here)
for 4WD: (Click here)


6. INSTALL PROPELLER SHAFT ASSEMBLY (for 4WD)
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assembly with the 4 washers, 4 bolts and 4 nuts.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }

  1. Align the matchmarks on the propeller shaft flange and transfer flange.

  1. Install the propeller shaft assembly with the 4 washers and 4 nuts.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



7. INSTALL PROPELLER SHAFT ASSEMBLY (for 2WD)
  1. Remove SST from the extension housing.

    SST
    09325-40010  

  1. Install the propeller shaft assembly to the extension housing.

  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assembly with the 4 washers, 4 bolts and 4 nuts.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



8. INSTALL FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft assembly with the 4 washers, 4 bolts and 4 nuts.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }

  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft assembly with the 4 washers and 4 nuts.

    Torque:
    88 N*m{ 899 kgf*cm , 65 ft.*lbf }



9. CONNECT NO. 1 AND NO. 2 FUEL PIPES
  1. Connect the No. 1 and No. 2 fuel pipes (Click here).

  1. Install the No. 2 fuel pipe clamp to the connector.



10. CONNECT HEATER WATER HOSE ASSEMBLY


    A225435E02
  1. Connect the 2 hoses and heater water hose assembly.
    Text in Illustration 
    *a
    Top
    *b
    LH Side

    HINT:
    The direction of the hose clamp is indicated in the illustration.



11. CONNECT ENGINE WIRE


  1. Connect the ECM connector.



      A226129E01
    1. Attach the grommet to the wire harness support.
      Text in Illustration 
      *1
      Grommet
      *2
      Wire Harness Support

    2. Pass the wire harness into the vehicle and install the wire harness support.



    3. A227938
    4. Connect the 6 connectors and attach the clamp.



  1. for 4WD:



      A222168
    1. Attach the clamp and connect the connector.



    A222166
  1. Connect the connector and install the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



12. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)


13. INSTALL FLYWHEEL HOUSING SIDE COVER


14. INSTALL STARTER ASSEMBLY
  1. Install the starter with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Connect the starter wire with the bolt and nut.

    Torque:
    for bolt:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
    for nut:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Close the terminal cap.

  1. Connect the starter connector.

  1. Connect the ground wire with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



15. INSTALL STARTER COVER
  1. Install the starter cover with the 3 bolts.

    Torque:
    12 N*m{ 117 kgf*cm , 8 ft.*lbf }



16. INSTALL GENERATOR ASSEMBLY
  1. Install the generator bracket to the generator with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Install the generator with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Install the generator bracket with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Attach the wire harness clamp.

  1. Install the wire harness with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the generator connector to the generator.

  1. Install the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Close the terminal cap.



17. INSTALL WIRING HARNESS CLAMP BRACKET
  1. Install the wiring harness clamp bracket with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Attach the clamp.



18. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A222094E01
  1. Install a new gasket onto the cylinder head.
    Text in Illustration 
    *1
    Protrusion
    V100135
    Front

    NOTICE:
    Be careful of the installation direction.

  1. Temporarily install the exhaust manifold sub-assembly LH with 6 new nuts.



    A222092E02
  1. Tighten the 6 nuts in the sequence shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.



19. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
  1. Install the No. 2 exhaust manifold heat insulator with the 3 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



20. INSTALL NO. 2 AIR TUBE


    A289303E01
  1. Install 2 new gaskets to the No. 2 air tube.
    Text in Illustration 
    *1
    New Gasket
    *2
    No. 2 Air Tube

    NOTICE:
    Be careful not to damage the installation surfaces of the gaskets.

  1. Install the No. 2 air tube with the 2 bolts and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



21. INSTALL NO. 2 MANIFOLD STAY
  1. Install the manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



22. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A222095E01
  1. Install a new gasket onto the cylinder head.
    Text in Illustration 
    *1
    Protrusion
    V100135
    Front

    NOTICE:
    Be careful of the installation direction.

  1. Temporarily install the exhaust manifold sub-assembly RH with 6 new nuts.



    A222089E02
  1. Tighten the 6 nuts in the sequence shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.



23. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
  1. Install the No. 1 exhaust manifold heat insulator with the 3 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



24. INSTALL AIR TUBE


    A289302E01
  1. Install 2 new gaskets to the air tube.
    Text in Illustration 
    *1
    New Gasket
    *2
    Air Tube

    NOTICE:
    Be careful not to damage the installation surfaces of the gaskets.

  1. Install the air tube with the 2 bolts and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



25. INSTALL MANIFOLD STAY
  1. Install the manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



26. INSTALL FRONT EXHAUST PIPE ASSEMBLY
(Click here)


27. INSTALL COOLER COMPRESSOR ASSEMBLY


E195719E01
  1. Install the cooler compressor with the stud bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the 3 bolts and nut.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    HINT:
    Tighten the bolts and nut in the order shown in the illustration.

  1. Connect the connector.



28. CONNECT SUCTION HOSE SUB-ASSEMBLY
  1. Remove the attached vinyl tape from the suction hose.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring to the suction hose.



    E199373E01
  1. Connect the suction hose with the 2 bolts.

    Torque:
    for bolt A:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }
    for bolt B:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



29. CONNECT DISCHARGE HOSE SUB-ASSEMBLY
  1. Remove the attached vinyl tape from the cooler refrigerant discharge hose.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring to the discharge hose.

  1. Connect the discharge hose to the cooler compressor with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



30. CONNECT VANE PUMP ASSEMBLY
  1. Connect the vane pump assembly with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Attach the 2 wire harness clamps.

  1. Connect the 2 connectors.



31. INSTALL INTAKE AIR SURGE TANK
  1. Install a new gasket to the intake air surge tank.



    A306010E01
  1. Install the intake air surge tank with the 4 bolts and 2 nuts in the order shown in the illustration.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

  1. Install the No. 1 surge tank stay with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Attach the wire harness clamp.

  1. Install the No. 2 surge tank stay with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the throttle body bracket with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    A225183E01
  1. Connect the No. 1 ventilation hose.
    Text in Illustration 
    *a
    Front
    *b
    Matchmark
    *c
    Top

  1. Connect the No. 1 vacuum switching valve connector.

  1. Connect the No. 1 vapor fuel feed hose.

    HINT:
    Connect the hose so that the direction of the hose clamp is as indicated in the illustration.



    A225184E01
  1. Connect the throttle body connector.
    Text in Illustration 
    *a
    Front
    *b
    Matchmark
    *c
    RH

  1. Connect the No. 4 water by-pass hose.

  1. Connect the No. 5 water by-pass hose.

    HINT:
    Connect the hose so that the direction of the hose clamp is as indicated in the illustration.

  1. Attach the 2 heater hose clamps.



32. INSTALL AIR TUBE ASSEMBLY


  1. for Bank 1 Side:



      A226131E04
    1. Align the paint mark with the projection and connect the air tube assembly to the No. 1 emission control valve set.
      Text in Illustration 
      *a
      Projection
      *b
      Paint Mark
      *c
      Upper
      *d
      RH

      HINT:
      Make sure the direction of the hose clamp is as shown in the illustration.



  1. for Bank 2 Side:



      A226132E04
    1. Align the paint mark with the projection and connect the air tube assembly to the No. 2 emission control valve set.
      Text in Illustration 
      *a
      Paint Mark
      *b
      Projection
      *c
      Upper
      *d
      LH

      HINT:
      Make sure the direction of the hose clamp is as shown in the illustration.

  1. Install the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



33. INSTALL RADIATOR ASSEMBLY


    A224958
  1. Insert the radiator bracket hooks into the radiator support holes.

  1. Install the radiator with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



    A224976E01
  1. Connect the 2 oil cooler hoses and slide the 2 clamps to secure them.
    Text in Illustration 
    *a
    Upper

    HINT:
    Make sure the direction of the hose clamp is as shown in the illustration.



34. INSTALL FAN SHROUD
  1. Install the fan pulley to the water pump.

  1. Place the fan shroud together with the coupling fan between the radiator and engine.

    NOTICE:
    Be careful not to damage the radiator core.



    A229548E03
  1. Align the paint marks on the heads of the water pump stud bolts with the paint marks of the same color on the outer edge of the fluid coupling flange and install the fluid coupling to the water pump.
    Text in Illustration 
    *a
    Paint Mark

  1. Temporarily install the fan with fluid coupling to the water pump with the 4 nuts. Tighten the nuts as much as possible by hand.



    A223087
  1. Attach the claws of the shroud to the radiator as shown in the illustration.

  1. Install the fan shroud with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the fan with fluid coupling and generator V-belt (Click here).

  1. Tighten the 4 nuts of the fan with fluid coupling.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



35. CONNECT OIL COOLER TUBE


    A226789
  1. Connect the oil cooler tube with the 2 bolts, and attach the claw to close the flexible hose clamp.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



36. INSTALL RADIATOR RESERVOIR TANK
  1. Install the radiator reservoir tank with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the reservoir hose to upper side of the radiator tank upper.



37. INSTALL NO. 2 RADIATOR HOSE


    A306026E03
  1. Connect the No. 2 radiator hose with the clamp so that its paint mark aligns with the radiator protrusion as shown in the illustration.
    Text in Illustration 
    *a
    Paint Mark
    *b
    Protrusion
    *c
    Upper

    HINT:
    Make sure the direction of the hose clamp is as shown in the illustration.



    A227083E04
  1. Connect the No. 2 radiator hose with the clamp so that its paint mark aligns with the water inlet housing protrusion as shown in the illustration.
    Text in Illustration 
    *a
    Paint Mark
    *b
    Protrusion
    *c
    Front
    *d
    Upper

    HINT:
    Make sure the direction of the hose clamp is as shown in the illustration.



38. INSTALL NO. 1 RADIATOR HOSE


    A227085E03
  1. Connect the No. 1 radiator hose to the water inlet housing with the clamp shown in the illustration labeled A.
    Text in Illustration 
    *a
    Paint Mark
    *b
    Protrusion
    *c
    Front
    *d
    Upper

    HINT:
    1. Make sure the paint mark of the No. 1 radiator hose is facing upward.
    2. Make sure the direction of the hose clamp is as shown in the illustration.

  1. Connect the No. 1 radiator hose with the clamp so that its paint mark aligns with the radiator protrusion as shown in the illustration labeled B.

    HINT:
    1. Make sure the paint mark of the No. 1 radiator hose is facing upward.
    2. Make sure the direction of the hose clamp is as shown in the illustration.



39. INSTALL RADIATOR SIDE DEFLECTOR LH
  1. Attach the 3 claws.

  1. Install the radiator side deflector LH with the clip.



40. INSTALL RADIATOR SIDE DEFLECTOR RH
  1. Attach the 3 claws.

  1. Install the radiator side deflector RH with the clip.



41. INSTALL UPPER FRONT BUMPER RETAINER
  1. Install the upper front bumper retainer with the 3 bolts and 2 screws.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf } (for Bolt)



42. INSTALL AIR CLEANER CASE SUB-ASSEMBLY
  1. Install the air cleaner case sub-assembly with the 3 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Attach the wire harness clamp.

  1. Install the air cleaner filter element sub-assembly.



43. INSTALL AIR CLEANER CAP AND HOSE


    A223697E01
  1. Install the air cleaner cap and hose.
    Text in Illustration 
    *a
    Upper
    *b
    Front
    *c
    RH
    *d
    Align cutout portion of hose with protrusion of throttle
    *e
    Paint Mark

    1. Install the air cleaner cap and hose with the bolt and fasten the 4 hook clamps.

      Torque:
      5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    2. Tighten the clamp.

      Torque:
      5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    3. Attach the 4 clamps and connect the ventilation hose, vacuum hose and mass air flow meter connector.

      HINT:
      The direction of the hose clamp is indicated in the illustration.



44. INSTALL FRONT BUMPER COVER
w/o Intuitive Parking Assist System: (Click here)
w/ Intuitive Parking Assist System: (Click here)


45. INSTALL V-BANK COVER


    A229926E01
  1. Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins and press down on the V-bank cover to attach the pins.
    Text in Illustration 
    *1
    Pin
    *2
    V-bank Cover Hook



46. INSTALL BATTERY TRAY


47. INSTALL BATTERY


48. INSTALL BATTERY HOLD DOWN CLAMP
  1. Install the battery clamp with the 2 nuts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



49. CONNECT CABLE TO POSITIVE BATTERY TERMINAL


50. ADD ENGINE COOLANT
  1. Tighten the cylinder block drain cock plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Tighten the radiator drain cock plug by hand.

  1. Add engine coolant.

    Standard Capacity:
    10.5 liters (11.1 US qts, 9.2 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Slowly pour coolant into the radiator reservoir until it reaches the F line.

  1. Install the reservoir cap.

  1. Install the radiator cap.*1

  1. Start the engine and stop it immediately.*2

  1. Allow approximately 10 seconds to pass. Then remove the radiator cap and check the coolant level. If the coolant level has decreased, add coolant.*3

  1. Repeat steps *1, *2 and *3 until the coolant level does not decrease.

    HINT:
    Be sure to perform this step while the engine is cold, as air in the No. 1 radiator hose will flow into the radiator if the engine is warmed up and the thermostat opens.

  1. Install the radiator cap.*4

  1. Set the air conditioning as follows.*5
    Item
    Condition
    Fan speed
    Any setting except off
    Temperature
    Toward WARM
    Air conditioning switch
    Off

  1. Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the coolant.*6

    CAUTION:
    1. Wear protective gloves. Hot areas on the parts may injure your hands.
    2. Be careful of the fan.
    3. Be careful as the engine, radiator and radiator hoses are hot and can cause burns.

    NOTICE:
    1. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the F line.
    2. Do not start the engine when there is no coolant in the radiator reservoir.
    3. Pay attention to the needle of the engine coolant temperature receiver gauge. Make sure that the needle does not show an abnormally high temperature.
    4. If there is not enough coolant, the engine may burn out or overheat.

    HINT:
    1. Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air while warming up the engine.
    2. The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand and checking when the engine coolant starts to flow inside the hose.

  1. Stop the engine, wait until the engine coolant cools down to ambient temperature. Then remove the radiator cap and check the coolant level.*7

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. If the coolant level has decreased, add coolant and warm up the engine until the thermostat opens.*8

  1. If the coolant level has not decreased, check that the coolant level in the radiator reservoir is at the F line.
    If the coolant level is below the F line, repeat steps *4 through *8.
    If the coolant level is above the F line, drain coolant until the coolant level reaches the F line.



51. ADD ENGINE OIL


  1. Add fresh engine oil.

    NOTICE:
    A308107
    Do not allow engine oil to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.

    If engine oil is on the location indicated by the arrow, replace the belt tensioner.

    Standard Engine Oil:

    Oil Grade
    Oil Viscosity (SAE)
    ILSAC multigrade engine oil
    0W-20


    Standard Oil Capacity:

    Item
    Specified Condition
    Drain and refill without oil filter change
    5.7 liters (6.0 US qts, 5.0 Imp. qts)
    Drain and refill with oil filter change
    6.2 liters (6.6 US qts, 5.5 Imp. qts)
    Dry fill
    7.1 liters (7.5 US qts, 6.2 Imp. qts)



52. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
(Click here)


53. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



54. INSPECT FOR FUEL LEAK
  1. Make sure that there are no fuel leaks after performing maintenance on the fuel system.

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON and turn the Techstream on.

      NOTICE:
      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

    4. Check that there are no leaks from the fuel system.
      If there are fuel leaks, repair or replace parts as necessary.

    5. Turn the ignition switch off.

    6. Disconnect the Techstream from the DLC3.



55. INSPECT FOR ENGINE OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.



56. INSPECT FOR EXHAUST GAS LEAK


57. CHECK ENGINE OIL LEVEL
  1. Warm up the engine, and then stop the engine and wait for 5 minutes.

  1. Check that the engine oil level is between the low level and full level marks on the dipstick.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.

    HINT:
    Engine oil is always being consumed when driving the vehicle.
    Generally, engine oil consumed at a rate of 1 liter every 3000 km, or 1 US qts. every 2000 miles.
    In the following situations, oil consumption may increase and it may be necessary to add oil between maintenances.
    1. The engine is new.
    2. The oil quality is poor or the viscosity is inappropriate.
    3. The engine speed or load is high, the vehicle is towing something or the vehicle is being accelerated and decelerated frequently.
    4. The engine is idled for a very long time or the vehicle is frequently driven in traffic.



58. INSTALL UPPER RADIATOR SUPPORT SEAL
  1. Install the upper radiator support seal with the 13 clips.



59. INSTALL FRONT NO. 1 FENDER APRON TO FRAME SEAL RH
  1. Install the front No. 1 fender apron to frame seal RH with the 5 clips.



60. INSTALL FRONT NO. 1 FENDER APRON TO FRAME SEAL LH
  1. Install the front No. 1 fender apron to frame seal LH with the 5 clips.



61. INSTALL FRONT FENDER APRON SEAL RH
  1. Install the front fender apron seal RH with the 4 clips.



62. INSTALL FRONT FENDER APRON SEAL LH
  1. w/o KDSS:

    1. Install the front fender apron seal LH with the 5 clips.

  1. w/ KDSS:

    1. Install the front fender apron seal LH with the 7 clips.



63. INSTALL REAR ENGINE UNDER COVER ASSEMBLY
  1. Install the rear engine under cover assembly with the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



64. INSTALL TRANSMISSION UNDER COVER
  1. Install the transmission under cover with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



65. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY


    A224743
  1. Hook the No. 1 engine under cover sub-assembly to the vehicle body as shown in the illustration.

  1. Install the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



66. INSTALL FRONT LOWER BUMPER COVER (w/o Intuitive Parking Assist System)
  1. Install the front lower bumper cover with the 5 bolts and clip.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



67. INSTALL AIR INTAKE DUCT LH (w/ Intuitive Parking Assist System)
  1. Install the air intake duct LH with the 2 screws.

  1. Install the clip and bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



68. INSTALL AIR INTAKE DUCT RH (w/ Intuitive Parking Assist System)

HINT:
Use the same procedure as for the LH side.



69. INSTALL FRONT LOWER BUMPER COVER (w/ Intuitive Parking Assist System)
  1. Install the front lower bumper cover with the 4 bolts and clip.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



70. INSTALL COOL AIR INTAKE DUCT (for 4WD with Intuitive Parking Assist System)
  1. Install the cool air intake duct with the 4 clips.



71. PERFORM RESET MEMORY
for 2WD: (Click here)
for 4WD: (Click here)


72. INSPECT IGNITION TIMING

NOTICE:
  1. Turn all electrical systems off.
  1. Perform the inspection when the cooling fan motor is turned off.

  1. Warm up the engine.

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

    2. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / IGN Advance.

    3. Inspect the ignition timing during idling.

      Standard ignition timing:
      8 to 12° BTDC @ idle (transmission in neutral and A/C switch off)

    4. Check that the ignition timing advances immediately when the engine speed is increased.



    A206183E05
  1. When not using the Techstream:

    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  
      Text in Illustration 
      *a
      Front view of DLC3

      NOTICE:
      Be sure not to improperly connect the terminals. This may damage the engine.

    2. Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

      NOTICE:
      1. Use a timing light that detects primary signals.
      1. After the inspection, be sure to wrap the wire harness with tape.



    3. A076316E01
    4. Inspect the ignition timing during idling.

      Standard ignition timing:
      8 to 12° BTDC @ idle (transmission in neutral and A/C switch off)

    5. Remove SST from the DLC3.

    6. Inspect the ignition timing during idling.

      Standard ignition timing:
      7 to 24° BTDC @ idle (transmission in neutral and A/C switch off)

    7. Disconnect the timing light from the engine.



73. INSPECT ENGINE IDLE SPEED

NOTICE:
  1. Turn all the electrical systems off.
  1. Perform the inspection when the cooling fan motor is turned off.

  1. Warm up the engine.

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

    2. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.

    3. Inspect the engine idle speed.

      Standard idle speed:
      690 to 790 rpm (transmission in neutral and A/C switch off)



    A206183E06
  1. When not using the Techstream:

    1. Connect SST to terminal 9 (TAC) of the DLC3.

      SST
      09843-18030  
      Text in Illustration 
      *a
      Front view of DLC3

    2. Race the engine at 2500 rpm for approximately 90 seconds.

    3. Inspect the engine idle speed.

      Standard idle speed:
      690 to 790 rpm (transmission in neutral and A/C switch off)



74. INSPECT CO/HC

HINT:
This check is to determine whether or not the idle CO/HC concentration complies with regulations.

  1. Start the engine.

  1. Run the engine at 2500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.31 ft) into the tailpipe during idling.

  1. Immediately check the CO/HC concentration during idling and/or at 2500 rpm.

    HINT:
    When carrying out the 2 tests (idling and 2500 rpm), the measurement orders are prescribed by the applicable local regulations.

  1. If the CO/HC concentration does not comply with regulations, perform troubleshooting in the order given below.

    1. Check the A/F sensor operation (Click here) and heated oxygen sensor operation (Click here).

    2. See the table below for possible causes, and then inspect and correct the corresponding causes if necessary.

      CO
      HC
      Symptom
      Causes
      Normal
      High
      Rough idling
      1. Faulty ignition:
        1. Incorrect timing
        2. Plugs are contaminated or shorted, or plug gaps are incorrect
      2. Incorrect valve clearance
      3. Leaky intake and exhaust valves
      4. Leaky cylinders
      Low
      High
      Rough idling
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. Ventilation hoses
        2. Intake manifold
        3. Throttle body
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Plugged PCV valve
      3. Faulty SFI system:
        1. Faulty pressure regulator
        2. Defective engine coolant temperature sensor
        3. Faulty mass air flow meter
        4. Faulty ECM
        5. Faulty injectors
        6. Faulty throttle position sensor



75. INSTALL HOOD SUB-ASSEMBLY


    A229695
  1. Install the hood sub-assembly with the 8 bolts.

    Torque:
    for bolt A:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }
    for bolt B:
    18 N*m{ 178 kgf*cm , 13 ft.*lbf }

    Text in Illustration 
    V100135
    Bolt A
    V100136
    Bolt B

  1. Connect the washer nozzle hose.



76. ADJUST HOOD SUB-ASSEMBLY


  1. Adjust the hood position.



      B237105
    1. Loosen the 4 hinge bolts on the hood sub-assembly.

    2. Move the hood sub-assembly and adjust the clearance between the hood sub-assembly and front fender.

    3. Tighten the 4 hinge bolts on the hood sub-assembly after the adjustment.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }



  1. Adjust the height of the front end of the hood sub-assembly using the cushion rubbers.



      B237106
    1. Adjust the cushion rubbers so that the hood sub-assembly and front fender are aligned.

      HINT:
      Raise or lower the front end of the hood sub-assembly by turning the 2 cushion rubbers.



  1. Adjust the hood lock.



      B237107
    1. Loosen the 3 bolts.

    2. Adjust the hood lock assembly and tighten the 3 bolts.

      Torque:
      7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    3. Check that the striker can engage with the hood lock assembly smoothly.



77. CHARGE REFRIGERANT
SST
09985-20010   (09985-02130, 09985-02150, 09985-02090, 09985-02110, 09985-02010, 09985-02050, 09985-02060, 09985-02070)
  1. Perform vacuum purging using a vacuum pump.



  1. Charge refrigerant HFC-134a (R134a).

    Standard:
    550 +/-30 g (19.3 +/-1.0 oz.)



    I037365E19

    NOTICE:
    1. Do not operate the cooler compressor before charging refrigerant as the cooler compressor does not work properly without any refrigerant and overheats.
    2. Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear.



78. WARM UP ENGINE
  1. Warm up the engine at less than 1850 rpm for 2 minutes or more after charging the refrigerant.

    NOTICE:
    Be sure to warm up the compressor by turning the A/C switch on after removing and installing the cooler refrigerant lines (including the compressor) to prevent damage to the compressor.



79. CHECK FOR REFRIGERANT GAS LEAK
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation under these conditions:

    1. Stop the engine.
    2. Secure good ventilation (the halogen leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that some refrigerant remains in the refrigeration system. When the compressor is off: approximately 392 to 588 kPa (4.0 to 6.0 kgf/cm2, 57 to 85 psi).



    I042222E34
  1. Using a halogen leak detector, check the refrigerant line for leakage.
    Text in Illustration 
    *1
    Halogen Leak Detector
    *a
    Check for Leakage

  1. If a gas leak from the drain hose is not detected, remove the blower motor control (blower resistor) from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.

  1. Disconnect the connector and wait for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.