DTC P000A Camshaft Position "A" - Timing Slow Response Bank 1 |
DTC P000C Camshaft Position "A" - Timing Slow Response Bank 2 |
DTC P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) |
DTC P0021 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P000A | Integrated deviations in target intake valve timing and actual intake valve timing per specified time exceed thresholds (bank 1). (2 trip detection logic) |
|
| P0011 | Deviation in target intake valve timing and actual intake valve timing exceeds thresholds (bank 1). (2 trip detection logic) | |
| P000C | Integrated deviations in target intake valve timing and actual intake valve timing per specified time exceed thresholds (bank 2). (2 trip detection logic) |
|
| P0021 | Deviation in target intake valve timing and actual intake valve timing exceeds thresholds (bank 2). (2 trip detection logic) |

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P000A, P000C, P0011 OR P0021) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P000A, P000C, P0011 or P0021 is output | A |
| DTC P000A, P000C, P0011 or P0021 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING GTS (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY) |
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Turn the A/C switch on.
Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Linear (Bank 1), Control the VVT Linear (Bank 2).
Check the engine speed while operating the camshaft timing oil control valve assembly (for intake camshaft) using the GTS.
| GTS Operation | Specified Condition |
| 0 deg (CA) | Normal engine speed |
| 36 deg (CA) | Engine idles roughly or stalls |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P000A, P000C, P0011 OR P0021) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
Read pending DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P000A, P000C, P0011 or P0021 is output | B |
|
| ||||
| A | |
| 4.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH) |
Check the valve timing (Click here).
|
| ||||
| OK | |
| 5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT) |
Inspect the camshaft timing oil control valve assembly (for intake camshaft) (Click here).
|
| ||||
| OK | |
| 6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY |
Inspect the camshaft timing gear assembly .
|
| ||||
| OK | |
| 7.CLEAN LUBRICATION SYSTEM |
Replace the engine oil (Click here).
Warm up the engine for 5 minutes, and then stop the engine.
Replace the engine oil and filter (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P000A, P000C, P0011 OR P0021) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
Read pending DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P000A, P000C, P0011 or P0021 is output | B |
|
| ||||
| A | ||
| ||