DTC P000B Camshaft Position "B" - Timing Slow Response Bank 1 |
DTC P000D Camshaft Position "B" - Timing Slow Response Bank 2 |
DTC P0014 Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1) |
DTC P0024 Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P000B | Integrated deviations in target exhaust valve timing and actual exhaust valve timing per specified time exceed threshold (bank 1). (2 trip detection logic) |
|
| P0014 | Deviation in target exhaust valve timing and actual exhaust valve timing exceeds threshold for 8 seconds (bank 1). (2 trip detection logic) | |
| P000D | Integrated deviations in target exhaust valve timing and actual exhaust valve timing per specified time exceed threshold (bank 2). (2 trip detection logic) |
|
| P0024 | Deviation in target exhaust valve timing and actual exhaust valve timing exceeds threshold for 8 seconds (bank 2). (2 trip detection logic) |

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P000B, P000D, P0014 OR P0024) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P000B, P000D, P0014 or P0024 is output | A |
| DTC P000B, P000D, P0014 or P0024 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING GTS (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY) |
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Turn the A/C switch on.
Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Exhaust Linear (Bank 1), Control the VVT Exhaust Linear (Bank 2).
Check the engine speed while operating the camshaft timing oil control valve assembly (for exhaust camshaft) using the GTS.
| GTS Operation | Specified Condition |
| 0 deg (CA) | Normal engine speed |
| 51 deg (CA) | Engine idles roughly or stalls |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P000B, P000D, P0014 OR P0024) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
Read pending DTCs.
| Result | Proceed to |
| DTC P000B, P000D, P0014 or P0024 is output | A |
| DTC is not output | B |
|
| ||||
| A | |
| 4.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH) |
Check the valve timing (Click here).
|
| ||||
| OK | |
| 5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT) |
Inspect the camshaft timing oil control valve assembly (for exhaust camshaft) (Click here).
|
| ||||
| OK | |
| 6.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
Inspect the camshaft timing exhaust gear assembly .
|
| ||||
| OK | |
| 7.CLEAN LUBRICATION SYSTEM |
Replace the engine oil (Click here).
Warm up the engine for 5 minutes, and then stop the engine.
Replace the engine oil and filter (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P000B, P000D, P0014 OR P0024) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
Read pending DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P000B, P000D, P0014 or P0024 is output | B |
|
| ||||
| A | ||
| ||