Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1271    Low Output Signal of Front Speed Sensor RH (Test Mode DTC)

DTC    C1272    Low Output Signal of Front Speed Sensor LH (Test Mode DTC)

DTC    C1330    Open in Front Speed Sensor RH

DTC    C1331    Open in Front Speed Sensor LH

DTC    C1464    Front Speed Sensor RH

DTC    C1465    Front Speed Sensor LH

for Preparation Click here


DESCRIPTION

Each speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used by the brake control system.
Speed sensor rotors have row of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.
Each speed sensor detects that magnetic field change and sends a pulse signal to the skid control ECU (brake actuator assembly).
DTCs C1271 and C1272 are cleared when the speed sensor sends a vehicle speed signal or when Test Mode ends. DTCs C1271 and C1272 are output only in Test Mode.

F100269E14


DTC No.
DTC Detection Condition
Trouble Area
C1330
C1331
An open or short in the speed sensor signal circuit.
  1. Front speed sensor RH/LH
  2. Speed sensor circuit
  3. Sensor installation
  4. Skid control ECU (Brake actuator assembly)
C1464
C1465
An abnormal signal is received from a wheel speed sensor.
  1. Front speed sensor RH/LH
  2. Speed sensor circuit
  3. Front speed sensor rotor RH/LH (Front axle hub sub-assembly RH/LH)
  4. Sensor installation
  5. Skid control ECU (Brake actuator assembly)
C1271
C1272
Detected only during Test Mode.
  1. Front speed sensor RH/LH
  2. Sensor installation
  3. Front speed sensor rotor RH/LH (Front axle hub sub-assembly RH/LH)

HINT:
  1. DTCs C1271, C1330 and C1464 are for the front speed sensor RH.
  2. DTCs C1272, C1331 and C1465 are for the front speed sensor LH.


WIRING DIAGRAM


C261863E01


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization (Click here).

1.READ VALUE USING GTS (FRONT SPEED SENSOR)
  1. Connect the GTS to the DLC3.

  1. Start the engine.

  1. Select the Data List using the GTS (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    FL Wheel Speed
    Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations

  1. Check the speed value output from the speed sensor displayed on the GTS.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.



NG
Go to step 4
OK


2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
  1. Turn the ignition switch off.

  1. Perform the sensor check using the Test Mode procedure (Click here).

    OK:
    All Test Mode DTCs are not output.



NG
Go to step 4
OK


3.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTCs C1330, C1331, C1464 and C1465 are not output.
    A
    DTCs C1330, C1331, C1464 and/or C1465 are output.
    B



B
Go to step 9
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.CHECK FRONT SPEED SENSOR INSTALLATION


    C144929E60
  1. Turn the ignition switch off.

  1. Check the speed sensor installation.

    OK:
    There is no clearance between the sensor and the steering knuckle.
    The installation bolt is tightened properly.
    Torque:
    7.5 N*m (76 kgf*cm, 66 in.*lbf)



NG
INSTALL FRONT SPEED SENSOR CORRECTLY (Click here)
OK


5.CHECK FRONT SPEED SENSOR TIP
  1. Remove the front speed sensor (Click here).

  1. Check the speed sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).



NG
CLEAN OR REPLACE FRONT SPEED SENSOR
OK


6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
  1. Install the front speed sensor (Click here).

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU (brake actuator assembly) connector and the front speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    A5-16 (FR+) - A42-2 (FR+)
    Always
    Below 1 Ω
    A5-16 (FR+) - Body ground
    Always
    10 kΩ or higher
    A5-4 (FR-) - A42-1 (FR-)
    Always
    Below 1 Ω
    A5-4 (FR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    A5-19 (FL+) - A12-2 (FL+)
    Always
    Below 1 Ω
    A5-19 (FL+) - Body ground
    Always
    10 kΩ or higher
    A5-32 (FL-) - A12-1 (FL-)
    Always
    Below 1 Ω
    A5-32 (FL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT BRAKE ACTUATOR ASSEMBLY (FRONT SPEED SENSOR POWER SOURCE TERMINAL)
  1. Reconnect the skid control ECU (brake actuator assembly) connector.



    C261864E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    A42-2 (FR+) - Body ground
    Ignition switch ON
    8 to 14 V
    for LH:
    Tester Connection
    Condition
    Specified Condition
    A12-2 (FL+) - Body ground
    Ignition switch ON
    8 to 14 V

    Text in Illustration 
    *A
    for RH
    *B
    for LH
    *a
    Front view of wire harness connector
    (to Front Speed Sensor)



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


8.RECONFIRM DTC
  1. Reconnect the front speed sensor connector.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTCs C1330, C1331, C1464 and/or C1465 are output.
    A
    DTCs C1330, C1331, C1464 and C1465 are not output.
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


9.REPLACE FRONT SPEED SENSOR
  1. Turn the ignition switch off.

  1. Replace the front speed sensor (Click here).

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


10.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTCs C1330, C1331, C1464 and/or C1465 are output.
    A
    DTCs C1330, C1331, C1464 and C1465 are not output.
    B



B
END
A


11.REPLACE FRONT SPEED SENSOR ROTOR
  1. Turn the ignition switch off.

  1. Replace the front speed sensor rotor (Click here).

    HINT:
    If the front speed sensor rotor needs to be replaced, replace the front axle hub sub-assembly.

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


12.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTCs C1330, C1331, C1464 and/or C1465 are output.
    A
    DTCs C1330, C1331, C1464 and C1465 are not output.
    B

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



B
END
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)