Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > Brake Warning Light Remains ON

for Preparation Click here


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
If any of the following is detected, the brake warning light remains on:
  1. The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).
  2. The brake fluid level is insufficient.
  3. The parking brake is applied.
  4. EBD operation is not possible.

WIRING DIAGRAM


C264063E01


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC is not output.
    A
    DTC is output.
    B



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU (brake actuator assembly) connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3.CHECK BATTERY
  1. Check the battery voltage.

    Standard Voltage:
    11 to 14 V



NG
CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


    C261861E07
  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A5-25 (+BS) - Body ground
    Always
    11 to 14 V
    A5-25 (+BS) - A5-38 (GND1)
    Always
    11 to 14 V
    A5-28 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V
    A5-28 (IG1) - A5-38 (GND1)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)


    C261861E06
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A5-38 (GND1) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)
OK


6.READ VALUE USING GTS (PARKING BRAKE SWITCH)
  1. Reconnect the skid control ECU (brake actuator assembly) connector.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select the Data List using the GTS (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Parking Brake SW
    Parking brake switch / ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -

  1. Using the GTS, check the switch operation signal received when the parking brake is operated.

    OK:
    When the parking brake is operated, the display changes as shown above.



NG
Go to step 10
OK


7.INSPECT BRAKE FLUID LEVEL WARNING SWITCH


    C261878E01
  1. Turn the ignition switch off.

  1. Remove the reservoir filler cap and the strainer.

  1. Disconnect the brake fluid level warning switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    A float is located inside the reservoir. Its position changes according to the brake fluid level.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Switch OFF (Float up)
    1.9 to 2.1 kΩ
    1 - 2
    Switch ON (Float down)
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Brake Fluid Level Warning Switch (Brake Master Cylinder Sub-assembly))

    HINT:
    If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.


    Result:

    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE BRAKE MASTER CYLINDER SUB-ASSEMBLY (Click here)

C
REPLACE BRAKE MASTER CYLINDER SUB-ASSEMBLY (Click here)
A


8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH)
  1. Disconnect the combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D7-17 (LBL) - A59-1
    Always
    Below 1 Ω
    D7-17 (LBL) - Body ground
    Always
    10 kΩ or higher
    A59-2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.INSPECT COMBINATION METER ASSEMBLY
  1. Reconnect the combination meter assembly connector and the brake fluid level warning switch connector.

  1. Perform an Active Test of the combination meter assembly (meter CPU) using the GTS (Click here).

  1. Check the combination meter assembly.

    OK:
    The brake warning light turns on or off in accordance with the Active Test operation.

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

10.INSPECT PARKING BRAKE SWITCH ASSEMBLY


    C211519E05
  1. Turn the ignition switch off.

  1. Disconnect the parking brake switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - Body ground
    Parking brake switch ON
    (Switch pin free)
    Below 1 Ω
    1 - Body ground
    Parking brake switch OFF
    (Switch pin pushed in)
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Parking Brake Switch Assembly)



NG
REPLACE PARKING BRAKE SWITCH ASSEMBLY (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - PARKING BRAKE SWITCH ASSEMBLY)
  1. Disconnect the instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-24 - D31-1
    Always
    Below 1 Ω
    3B-24 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly .



  1. Measure the resistance according to the value(s) in the table below.


    E249231E02


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    MB-14 (PKB) - 3B-24
    Always
    Below 1 Ω
    MB-14 (PKB) - Body ground
    Always
    10 kΩ or higher

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)