Home › Engine / Hybrid System › FA20 ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > VC Output Circuit

for Preparation Click here


DESCRIPTION

The ECM constantly generates 5 V power from the battery voltages supplied to the +B terminal and +B2 terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A280171E01

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are deactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated when the ignition switch is turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM


A280170E01


A282622E01


INSPECTION PROCEDURE

1.CHECK MIL CONDITION
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

    OK:
    MIL lights up.


    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A


2.CHECK CONNECTION BETWEEN GTS AND ECM
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Check for communication between the tester and ECM.

    Result 
    Result
    Proceed to
    Communication is not possible
    A
    Communication is possible
    B



B
GO TO MIL CIRCUIT (Click here)
A


3.CHECK MIL (THROTTLE POSITION SENSOR)
  1. Disconnect the throttle with motor body assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
A


4.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR (Click here)
A


5.CHECK MIL (FUEL PRESSURE SENSOR)
  1. Disconnect the fuel pressure sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE FUEL PRESSURE SENSOR (Click here)
A


6.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)
  1. Disconnect the accelerator pedal sensor assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY (Click here)
A


7.CHECK MIL (BATTERY CURRENT SENSOR ASSEMBLY)
  1. Disconnect the battery current sensor assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE BATTERY CURRENT SENSOR ASSEMBLY (Click here)
A


8.CHECK MIL (CANISTER PUMP MODULE)
  1. Disconnect the canister pump module connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
REPLACE CANISTER PUMP MODULE (Click here)
A


9.CHECK HARNESS AND CONNECTOR (EACH SENSOR - ECM)
  1. Disconnect the throttle with motor body assembly connector.

  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the fuel pressure sensor connector.

  1. Disconnect the accelerator pedal sensor assembly connector.

  1. Disconnect the battery current sensor assembly connector.

  1. Disconnect the canister pump module connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A36-19 (VC) - Body ground
    Always
    10 kΩ or higher
    A35-22 (VCP2) - Body ground
    Always
    10 kΩ or higher
    A35-21 (VCPA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)