Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P0451  Evaporative Emission Control System Pressure Sensor Range / Performance  P0452  Evaporative Emission Control System Pressure Sensor / Switch Low Input  P0453  Evaporative Emission Control System Pressure Sensor / Switch High Input  


DTC SUMMARY

DTC No. Monitoring Item Malfunction Detection Condition Trouble Area Detection Timing Detection Logic
P0451 Difference between canister pressure sensor output value and manifold absolute pressure sensor output value The difference between the canister pressure sensor output value and the manifold absolute pressure sensor output value with the ignition switch ON is large.
·

Canister pump module

·

Connector/wire harness

(Canister pump module - ECM)

·

EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)

·

ECM


Ignition switch off to ON 2 trip
P0452 Canister pressure sensor low input EVAP pressure sensor less than 0.973 V for 1 second.
·

Ignition switch ON

·

EVAP monitoring (ignition switch off)


1 trip
P0453 Canister pressure sensor high input EVAP pressure sensor more than 4.095 V for 1 second.
·

Ignition switch ON

·

EVAP monitoring (ignition switch off)


1 trip

HINT:

The canister pressure sensor is built into the canister pump module.


DESCRIPTION

The description can be found in EVAP (Evaporative Emission) System (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>EVAP System).

MONITOR DESCRIPTION

A282306E08
4.5,3.302 5.073,2.667 false 4.552,1.427 5.125,0.792 false 0.083,0.094 3.146,0.5 3.063,0.406 10 false Canister Pressure Sensor Specification 1.292,0.75 2.313,1.063 1.021,0.313 10 false Output Voltage 1.75,1.469 2.26,1.646 0.51,0.177 10 false 4.095 V 1.75,3.031 2.26,3.208 0.51,0.177 10 false 0.973 V 1.906,1.917 2.281,2.094 0.375,0.177 10 false 4.0 V 1.906,2.615 2.281,2.792 0.375,0.177 10 false 1.5 V 2.948,3.448 3.156,3.646 0.208,0.198 10 false 61 2.948,3.615 3.333,3.813 0.385,0.198 10 false (458) 3.635,3.615 4.021,3.813 0.385,0.198 10 false (803) 3.615,3.448 3.917,3.646 0.302,0.198 10 false 107 4.354,3.438 5,3.615 0.646,0.177 10 false kPa (abs) 4.354,3.604 5.292,3.781 0.938,0.177 10 false [mmHg] (abs) 5.219,3.344 5.917,3.656 0.698,0.313 10 false Pressure 5.135,2.531 6.24,2.844 1.104,0.313 10 false Malfunction Area 5.156,0.635 6.26,0.948 1.104,0.313 10 false Malfunction Area 3.802,2.323 4.74,2.646 0.938,0.323 10 false Usable Range 1.521,3.99 2.24,4.323 0.719,0.333 10 false HINT: 1.521,4.281 6.229,4.615 4.708,0.333 10 false Standard atmospheric pressure is 101.3 kPa (abs) [760 mmHg (abs)]

1.

DTC P0451: Difference between canister pressure sensor output value and manifold absolute pressure sensor output value

If the difference between the atmospheric pressure calculated using the canister pressure sensor and that calculated using the MAP sensor exceeds the specified value, then the ECM determines there is a canister pressure sensor abnormality. The ECM then illuminates the MIL and stores the DTC (2 trip detection logic).

2.

DTC P0452: Canister pressure sensor voltage low

If the canister pressure sensor voltage output (pressure) is below 0.973 V: 51.71 kPa(abs) [388 mmHg(abs)], the ECM interprets this as an open or short circuit in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).

3.

DTC P0453: Canister pressure sensor voltage high

If the canister pressure sensor voltage output (pressure) is 4.095 V: 108.99 kPa(abs) [818 mmHg(abs)] or more, the ECM interprets this as an open or short circuit in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).


CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.

4.

Check that the intake air temperature is between 4.4 and 35°C (40 and 95°F).

5.

Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

6.

Turn the ignition switch off and wait for at least 30 seconds.

7.

Turn the ignition switch to ON and turn the GTS on.

8.

Enter the following menus: Powertrain / Engine / Utility / All readiness.

9.

Input the DTC: P0451, P0452 or P0453.

10.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



11.

If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A282407E06
6.146,8.24 6.688,8.542 0.542,0.302 10 false ECM 0.698,8.063 1.292,8.427 0.594,0.365 10 false Battery 0.563,7.365 0.979,7.552 0.417,0.188 10 false MAIN 0.552,6.792 1.292,7 0.74,0.208 10 false EFI(CTRL) 2.208,4.615 2.5,4.781 0.292,0.167 10 false G8 2.208,4.781 4.563,5.156 2.354,0.375 10 false Canister Pump Module 5.479,6.479 5.792,6.656 0.313,0.177 10 false A35 5.49,4.271 5.802,4.448 0.313,0.177 10 false A35 5.49,3.854 5.802,4.031 0.313,0.177 10 false A35 5.49,3.448 5.802,3.625 0.313,0.177 10 false A35 5.49,2.375 5.802,2.552 0.313,0.177 10 false A35 5.49,1.656 5.802,1.833 0.313,0.177 10 false A35 5.49,0.604 5.802,0.781 0.313,0.177 10 false A36 5.813,0.604 6.167,0.76 0.354,0.156 10 false PRG 5.542,0.427 5.719,0.583 0.177,0.156 10 false 11 5.573,1.469 5.688,1.625 0.115,0.156 10 false 1 5.573,2.177 5.688,2.333 0.115,0.156 10 false 8 5.542,3.24 5.729,3.406 0.188,0.167 10 false 22 5.542,3.667 5.729,3.833 0.188,0.167 10 false 20 5.542,4.083 5.729,4.25 0.188,0.167 10 false 30 5.542,6.292 5.729,6.458 0.188,0.167 10 false 13 5.823,6.479 6.323,6.729 0.5,0.25 10 false SSHUT 5.833,4.281 6.271,4.49 0.438,0.208 10 false EPA2 5.833,3.854 6.302,4.042 0.469,0.188 10 false PPMP 5.833,3.448 6.302,3.646 0.469,0.198 10 false VCP2 5.833,2.365 6.302,2.563 0.469,0.198 10 false MPMP 5.833,1.646 6.302,1.844 0.469,0.198 10 false VPMP 2.719,0.823 3,1.021 0.281,0.198 10 false d1 2.719,0.979 3.854,1.302 1.135,0.323 10 false Purge Valve 2.375,1.542 2.521,1.76 0.146,0.219 10 false 5 2.385,2.271 2.531,2.49 0.146,0.219 10 false 3 4.573,1.542 4.771,1.76 0.198,0.219 10 false 1 3.396,0.49 3.594,0.708 0.198,0.219 10 false 1 4.573,2.25 4.771,2.469 0.198,0.219 10 false 4 4.563,3.323 4.76,3.542 0.198,0.219 10 false 6 4.573,4.146 4.771,4.365 0.198,0.219 10 false 8 4.573,3.74 4.771,3.958 0.198,0.219 10 false 7 1.948,6.865 2.667,7.26 0.719,0.396 10 false EFI MAIN1 2.625,6.375 2.854,6.625 0.229,0.25 10 false 1 1.865,6.385 2.094,6.635 0.229,0.25 10 false 2 2.625,6.031 2.854,6.281 0.229,0.25 10 false 3 1.865,6.031 2.094,6.281 0.229,0.25 10 false 5 2.552,0.49 2.708,0.688 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

When a vehicle is brought into the workshop, leave it as it is. Do not change the vehicle condition. For example, do not tighten the fuel cap.

·

Do not disassemble the canister pump module.

·

The GTS is required to conduct the following diagnostic troubleshooting procedure.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CONFIRM DTC AND EVAP PRESSURE
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON (do not start the engine).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read DTCs.


f.

Enter the following menus: Powertrain / Engine / Data List / Vapor Pressure Pump.


g.

Read the EVAP (Evaporative Emission) pressure displayed on the GTS.

Result
Display (DTC Output) Test Result Suspected Trouble Area Proceed to
P0451 -
·

Canister pressure sensor

·

Manifold absolute pressure sensor


C
P0452 Below 51.71 kPa(abs) [388 mmHg(abs)]
·

Wire harness/connector (ECM - Canister pressure sensor)

·

Canister pressure sensor

·

Short in ECM circuit


A
P0453 Higher than 108.99 kPa(abs) [818 mmHg(abs)]
·

Wire harness/connector (ECM - Canister pressure sensor)

·

Canister pressure sensor

·

Open in ECM circuit


B



A

2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

B

4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

C

8.READ VALUE USING GTS (ATMOSPHERE PRESSURE)
2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Result
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
A35-20 (PPMP) - Body ground Always Below 10 Ω
·

Wire harness/connector (ECM - Canister pressure sensor)

·

Short in canister pressure sensor circuit


A
10 kΩ or higher
·

Wire harness/connector (ECM - Canister pressure sensor)

·

Short in ECM circuit


B



A

3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

B

8.READ VALUE USING GTS (ATMOSPHERE PRESSURE)
3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Disconnect the canister pump module connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Result
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
A35-20 (PPMP) - Body ground Always 10 kΩ or higher Short in canister pressure sensor circuit A
Below 10 Ω Short in wire harness/connector (ECM - Canister pressure sensor) B



A

6.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM)

B

7.REPLACE ECM
4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.
U146804E03
1.552,0.292 1.844,0.448 0.292,0.156 10 false G8 0.135,0.104 0.448,0.333 0.313,0.229 10 false *a

Disconnect the canister pump module connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-8 - Body ground Always 100 Ω or less


Text in Illustration
*a Front view of wire harness connector
(to Canister Pump Module)


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G8-6 - Body ground Ignition switch ON 4.5 to 5.5 V
G8-7 - Body ground Ignition switch ON 4.5 to 5.5 V


Result
Test Result Suspected Trouble Area Proceed to
Voltage and resistance within standard ranges Open in canister pressure sensor circuit A
Voltage and/or resistance outside standard ranges Open in wire harness/connector (ECM - Canister pressure sensor) B



A

5.REPLACE CANISTER PUMP MODULE

B

7.REPLACE ECM
5.REPLACE CANISTER PUMP MODULE
a.

Replace the canister pump module (See page Engine / Hybrid System>FA20 EMISSION CONTROL>CANISTER>REMOVAL).



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
6.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM)

NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
7.REPLACE ECM

NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
8.READ VALUE USING GTS (ATMOSPHERE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Atmosphere Pressure.


e.

Compares Atmosphere Pressure displayed with the GTS to the actual atmosphere pressure.


Result
Result Proceed to
Difference with the actual atmosphere pressure is less than 4.7 kPa (abs) [36 mmHg (abs)]. A
Difference with the actual atmosphere pressure is 4.7 kPa (abs) [36 mmHg (abs)] or more. B


A

9.READ VALUE USING GTS (MAP)

B

10.REPLACE CANISTER PUMP MODULE
9.READ VALUE USING GTS (MAP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / MAP.


e.

Compares the MAP displayed with the GTS to the actual atmosphere pressure.


Result
Result Proceed to
Difference with the actual atmosphere pressure is less than 4.7 kPa (abs) [36 mmHg (abs)]. A
Difference with the actual atmosphere pressure is 4.7 kPa (abs) [36 mmHg (abs)] or more. B


A

B

11.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
10.REPLACE CANISTER PUMP MODULE
a.

Replace the canister pump module (See page Engine / Hybrid System>FA20 EMISSION CONTROL>CANISTER>REMOVAL).



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
11.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>VACUUM SENSOR>REMOVAL).



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
12.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 60 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Perform the Evaporative System Check using the GTS, referring to the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


j.

Input the DTC: P0451, P0452 or P0453.


k.

Check the DTC judgment result.

Result
GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit





NEXT

END