Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM › 2012.03–2016.06
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM J

FA20 ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V power from the battery voltages supplied to the +B terminal and +B2 terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A280171E04
1.844,0.76 3.292,1.208 1.448,0.448 10 false from EFI MAIN1 Relay 3.667,0.656 4.188,1.042 0.521,0.385 10 false +B2 3.688,0.99 4.021,1.25 0.333,0.26 10 false +B 4.958,0.885 6.885,1.333 1.927,0.448 10 false 5 V Constant Voltage Circuit 5.917,1.885 7.052,2.667 1.135,0.781 10 false Microprocessor 4.635,2.781 5.208,3.229 0.573,0.448 10 false R 3.073,1.729 4.229,1.948 1.156,0.219 10 false VC, VCP2, VCPA 0.354,1.719 2.802,2.292 2.448,0.573 10 false to Throttle Position Sensor, Accelerator Pedal Sensor Assembly, etc. (Sensors which have an IC) 0.417,2.573 2.833,2.781 2.417,0.208 10 false Mass Air Flow Meter, VVT Sensor etc.

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are deactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated when the ignition switch is turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A280170E05
5.219,1.729 5.771,2.073 0.552,0.344 10 false VTA1 5.219,1.396 5.698,1.76 0.479,0.365 10 false VTA2 5.219,2.094 5.573,2.396 0.354,0.302 10 false M+ 5.219,2.448 5.573,2.76 0.354,0.313 10 false M- 5.219,2.844 5.542,3.094 0.323,0.25 10 false E1 5.229,3.125 5.563,3.417 0.333,0.292 10 false VC 0.344,3.594 0.75,3.833 0.406,0.24 10 false C15 0.344,3.75 2.656,4 2.313,0.25 10 false Throttle with Motor Body Assembly 0.344,4.917 0.76,5.198 0.417,0.281 10 false C18 0.344,5.063 2.656,5.354 2.313,0.292 10 false Manifold Absolute Pressure Sensor 2.385,1.615 2.635,1.896 0.25,0.281 10 false 6 2.385,1.26 2.635,1.552 0.25,0.292 10 false 4 2.385,2 2.656,2.271 0.271,0.271 10 false 2 2.375,2.354 2.646,2.625 0.271,0.271 10 false 1 2.385,2.771 2.646,3.042 0.26,0.271 10 false 3 2.385,3.115 2.635,3.375 0.25,0.26 10 false 5 5.219,1.042 5.604,1.427 0.385,0.385 10 false EC 4.875,1.042 5.25,1.375 0.375,0.333 10 false A33 4.875,1.396 5.24,1.688 0.365,0.292 10 false A36 4.875,1.74 5.229,2 0.354,0.26 10 false A36 4.875,2.104 5.25,2.396 0.375,0.292 10 false A36 4.875,2.458 5.271,2.74 0.396,0.281 10 false A36 4.875,2.854 5.281,3.125 0.406,0.271 10 false A36 4.875,3.219 5.26,3.5 0.385,0.281 10 false A36 4.948,0.854 5.25,1.177 0.302,0.323 10 false 4 4.917,1.219 5.219,1.479 0.302,0.26 10 false 28 4.917,2.677 5.177,2.896 0.26,0.219 10 false 29 4.906,3.042 5.167,3.313 0.26,0.271 10 false 19 4.958,1.927 5.177,2.167 0.219,0.24 10 false 2 4.948,2.281 5.135,2.542 0.188,0.26 10 false 1 4.917,1.573 5.229,1.833 0.313,0.26 10 false 18 4.875,4.635 5.26,4.875 0.385,0.24 10 false A34 4.917,4.438 5.229,4.656 0.313,0.219 10 false 20 2.396,4.083 2.604,4.333 0.208,0.25 10 false 1 2.396,4.302 2.656,4.531 0.26,0.229 10 false 3 2.396,4.531 2.604,4.75 0.208,0.219 10 false 2 5.229,4.646 5.625,4.927 0.396,0.281 10 false PIM 0.344,6.281 0.76,6.563 0.417,0.281 10 false C10 0.344,6.427 1.719,6.813 1.375,0.385 10 false Fuel Pressure Sensor 4.875,5.99 5.271,6.229 0.396,0.24 10 false A34 4.948,5.792 5.229,6.073 0.281,0.281 10 false 9 2.396,5.406 2.635,5.656 0.24,0.25 10 false 2 2.385,5.667 2.604,5.938 0.219,0.271 10 false 1 2.396,5.896 2.594,6.135 0.198,0.24 10 false 3 5.24,5.99 5.573,6.219 0.333,0.229 10 false PR 5.885,7.635 6.292,7.823 0.406,0.188 10 false ECM 4.563,7.344 4.875,7.635 0.313,0.292 12 false A 1.948,1.74 2.406,2.052 0.458,0.313 10 false VTA1 1.927,1.406 2.417,1.76 0.49,0.354 10 false VTA2 2.052,2.115 2.448,2.427 0.396,0.313 10 false M+ 2.073,2.469 2.333,2.729 0.26,0.26 10 false M- 2.094,2.865 2.385,3.156 0.292,0.292 10 false E2 2.073,3.229 2.385,3.49 0.313,0.26 10 false VC 2.083,4.198 2.531,4.542 0.448,0.344 10 false E2 2.073,4.417 2.396,4.698 0.323,0.281 10 false VC 2.021,4.646 2.396,4.927 0.375,0.281 10 false PIM 2.094,5.5 2.406,5.792 0.313,0.292 10 false E2 2.083,5.76 2.406,6.083 0.323,0.323 10 false VC 2.083,6 2.417,6.26 0.333,0.26 10 false PR 3.135,6.958 3.938,7.156 0.802,0.198 10 false *: Shielded 3.469,1.917 3.656,2.063 0.188,0.146 10 false * 3.552,2.677 3.74,2.823 0.188,0.146 10 false *

A282622E07
0.479,4.927 2.021,5.229 1.542,0.302 10 false From EFI MAIN 1 Relay 0.26,7.625 0.698,7.781 0.438,0.156 10 false G8 0.26,7.802 2.219,8.188 1.958,0.385 10 false Canister Pump Module*1 2.563,8.188 4.521,8.573 1.958,0.385 10 false *1: w/ EVAP System 5.896,8.333 6.813,8.656 0.917,0.323 10 false ECM 4.792,7.313 5.104,7.469 0.313,0.156 10 false A35 4.792,6.948 5.083,7.104 0.292,0.156 10 false A35 4.792,6.594 5.083,6.76 0.292,0.167 10 false A35 4.844,6.396 5.031,6.573 0.188,0.177 10 false 20 4.885,6.771 5,6.927 0.115,0.156 10 false 8 4.885,7.135 5,7.292 0.115,0.156 10 false 1 5.135,7.313 5.583,7.552 0.448,0.24 10 false VPMP 5.135,6.938 5.583,7.177 0.448,0.24 10 false MPMP 5.135,6.583 5.583,6.823 0.448,0.24 10 false PPMP 2.302,5.781 2.417,5.948 0.115,0.167 10 false 8 2.302,5.281 2.417,5.448 0.115,0.167 10 false 3 2.302,3.115 2.417,3.281 0.115,0.167 10 false 3 2.281,0.521 2.396,0.688 0.115,0.167 10 false 6 2.292,0.885 2.406,1.052 0.115,0.167 10 false 3 2.292,1.229 2.406,1.396 0.115,0.167 10 false 4 2.292,1.563 2.406,1.729 0.115,0.167 10 false 5 2.292,3.323 2.406,3.49 0.115,0.167 10 false 1 2.281,2.302 2.396,2.469 0.115,0.167 10 false 1 2.302,3.552 2.417,3.719 0.115,0.167 10 false 2 2.292,1.938 2.406,2.104 0.115,0.167 10 false 2 2.292,3.896 2.406,4.063 0.115,0.167 10 false 4 2.302,5.51 2.417,5.677 0.115,0.167 10 false 5 2.302,6.115 2.417,6.281 0.115,0.167 10 false 6 2.302,6.5 2.417,6.667 0.115,0.167 10 false 7 2.302,6.865 2.417,7.031 0.115,0.167 10 false 4 2.302,7.208 2.417,7.375 0.115,0.167 10 false 1 0.281,4.26 0.698,4.427 0.417,0.167 10 false A11 0.281,4.406 2.458,4.927 2.177,0.521 10 false Battery Current Sensor Assembly 0.271,2.813 2.76,3.177 2.49,0.365 10 false Accelerator Pedal Sensor Assembly 1.917,3.219 2.25,3.438 0.333,0.219 10 false GND 1.844,3.656 2.25,3.875 0.406,0.219 10 false TEMP 1.833,3.979 2.26,4.198 0.427,0.219 10 false VOUT 1.99,3.417 2.26,3.635 0.271,0.219 10 false VIN 4.802,4 5.104,4.25 0.302,0.25 10 false A33 4.802,3.656 5.104,3.906 0.302,0.25 10 false A33 4.854,3.833 5.104,4.021 0.25,0.188 10 false 11 4.854,3.448 5.104,3.635 0.25,0.188 10 false 24 0.271,2.667 0.583,2.844 0.313,0.177 10 false A23 1.833,0.635 2.208,0.896 0.375,0.26 10 false VPA1 1.833,1 2.208,1.26 0.375,0.26 10 false VPA2 1.917,1.354 2.219,1.615 0.302,0.26 10 false VC1 1.917,2.396 2.219,2.656 0.302,0.26 10 false VC2 1.813,1.698 2.229,1.958 0.417,0.26 10 false GND1 1.813,2.083 2.229,2.344 0.417,0.26 10 false GND2 4.292,0.24 4.458,0.427 0.167,0.188 10 false A 4.792,0.625 5.094,0.865 0.302,0.24 10 false A35 4.802,0.979 5.104,1.219 0.302,0.24 10 false A35 4.802,1.323 5.104,1.563 0.302,0.24 10 false A35 4.802,1.688 5.104,1.927 0.302,0.24 10 false A35 4.802,2.042 5.104,2.281 0.302,0.24 10 false A35 4.802,2.406 5.104,2.646 0.302,0.24 10 false A35 4.844,0.417 5.042,0.656 0.198,0.24 10 false 23 2.958,0.823 3.948,1.083 0.99,0.26 10 false Shielded 5.146,0.615 5.531,0.865 0.385,0.25 10 false VPA 5.146,0.969 5.604,1.219 0.458,0.25 10 false VPA2 5.146,1.208 5.604,1.458 0.458,0.25 10 false VCPA 5.146,1.677 5.604,1.927 0.458,0.25 10 false EPA 5.146,2.042 5.604,2.292 0.458,0.25 10 false EPA2 5.146,2.292 5.604,2.542 0.458,0.25 10 false VCP2 5.146,3.656 5.604,3.906 0.458,0.25 10 false THB 5.156,4 5.615,4.25 0.458,0.25 10 false IB 4.844,0.802 5.083,1.021 0.24,0.219 10 false 31 4.844,1.146 5.083,1.365 0.24,0.219 10 false 21 4.844,1.5 5.083,1.719 0.24,0.219 10 false 29 4.833,1.854 5.073,2.073 0.24,0.219 10 false 30 4.844,2.229 5.083,2.448 0.24,0.219 10 false 22

PROCEDURE

1.CHECK MIL CONDITION
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

OK:

MIL lights up.


Result
Result Proceed to
NG A
OK B



A

2.CHECK CONNECTION BETWEEN GTS AND ECM

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check for communication between the tester and ECM.

Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

3.CHECK MIL (THROTTLE POSITION SENSOR)

B

3.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle with motor body assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

4.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)

B

REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

4.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

5.CHECK MIL (FUEL PRESSURE SENSOR)

B

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

5.CHECK MIL (FUEL PRESSURE SENSOR)
a.

Disconnect the fuel pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

6.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)

B

REPLACE FUEL PRESSURE SENSOR

6.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

7.CHECK MIL (BATTERY CURRENT SENSOR ASSEMBLY)

B

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

7.CHECK MIL (BATTERY CURRENT SENSOR ASSEMBLY)
a.

Disconnect the battery current sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

8.CHECK MIL (CANISTER PUMP MODULE)

B

REPLACE BATTERY CURRENT SENSOR ASSEMBLY

8.CHECK MIL (CANISTER PUMP MODULE)
a.

Disconnect the canister pump module connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

9.CHECK HARNESS AND CONNECTOR (EACH SENSOR - ECM)

B

REPLACE CANISTER PUMP MODULE

9.CHECK HARNESS AND CONNECTOR (EACH SENSOR - ECM)
a.

Disconnect the throttle with motor body assembly connector.


b.

Disconnect the manifold absolute pressure sensor connector.


c.

Disconnect the fuel pressure sensor connector.


d.

Disconnect the accelerator pedal sensor assembly connector.


e.

Disconnect the battery current sensor assembly connector.


f.

Disconnect the canister pump module connector.


g.

Disconnect the ECM connectors.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-19 (VC) - Body ground Always 10 kΩ or higher
A35-22 (VCP2) - Body ground Always 10 kΩ or higher
A35-21 (VCPA) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR