Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P0458  Evaporative Emission System Purge Control Valve Circuit Low  P0459  Evaporative Emission System Purge Control Valve Circuit High  


DESCRIPTION

To reduce hydrocarbon emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signals to the purge valve (Vacuum Switching Valve for Purge Control) so that the intake amount of hydrocarbon emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. DTC Detection Condition Trouble Area
P0458 The voltage of purge valve circuit is low for 2.5 seconds or more.
(2 trip detection logic)
·

Open or short in purge valve circuit

·

purge valve

·

ECM


P0459 The voltage of purge valve circuit is high for 2.5 seconds or more.
(2 trip detection logic)

MONITOR DESCRIPTION

The ECM monitors the output terminal voltage when the vacuum switching valve assembly is actuated. By turning the FET in the ECM on and off, the purge valve assembly is subject to duty control. If the ECM control value (drive signal) and the output terminal voltage duty cycle continue to not match, then the ECM interprets this as a malfunction in the vacuum switching valve circuit, illuminates the MIL, and stores the DTC.

CONFIRMATION DRIVING PATTERN

A280672E03
3.25,0.5 3.552,0.719 0.302,0.219 10 false [A] 5.49,1.573 5.792,1.792 0.302,0.219 10 false [B] 2.792,2.365 4.302,2.583 1.51,0.219 10 false 20 minutes or more 5.01,2.365 6.365,2.583 1.354,0.219 10 false 1 minute or more 0.063,0.667 1.198,1.063 1.135,0.396 10 false 80 km/h (50 mph) 0.219,1.688 1.219,2.063 1,0.375 10 false 0 km/h (0 mph) 0.177,0.115 1.188,0.51 1.01,0.396 10 false Vehicle Speed 6.385,2.24 7.104,2.635 0.719,0.396 10 false Time

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

Check the engine coolant temperature is 20°C (68°F) or less at engine started.


7.

Perform the following the confirmation driving pattern.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


(a)

Drive the vehicle at 80 km/h (50 mph) or more for 20 minutes or more [A].

(b)

Stop the vehicle.

(c)

Idle the engine for 1 minute or more [B].


8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P0458 or P0459.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



13.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A280072E07
2.719,1.052 2.969,1.365 0.25,0.313 10 false 1 3.906,1.052 4.156,1.365 0.25,0.313 10 false 2 3.063,1.563 3.958,1.813 0.896,0.25 10 false Purge Valve 4.969,1.042 5.302,1.344 0.333,0.302 10 false PRG 4.948,0.323 5.552,0.625 0.604,0.302 10 false SSHUT 5.396,2.677 5.917,2.927 0.521,0.25 10 false ECM 2.823,1.573 3.052,1.75 0.229,0.177 10 false d1 4.594,1.146 4.865,1.323 0.271,0.177 10 false A36 4.594,0.448 4.865,0.625 0.271,0.177 10 false A35 4.635,0.958 4.885,1.271 0.25,0.313 10 false 11 4.646,0.24 4.896,0.552 0.25,0.313 10 false 13 1,2.313 1.781,2.615 0.781,0.302 10 false EFI(CTRL) 1.135,1.552 1.917,1.854 0.781,0.302 10 false EFI MAIN1 1.125,3.135 1.906,3.438 0.781,0.302 10 false Battery 0.906,1.281 1.156,1.594 0.25,0.313 10 false 3 0.917,1.958 1.167,2.271 0.25,0.313 10 false 5 0.396,1.958 0.646,2.271 0.25,0.313 10 false 2 0.396,1.271 0.646,1.583 0.25,0.313 10 false 1 0.99,2.677 1.771,2.979 0.781,0.302 10 false MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A280659E02
0.458,1.708 0.823,1.906 0.365,0.198 10 false *a 2.135,1.708 2.5,1.906 0.365,0.198 10 false *b 1.448,0.385 1.698,0.583 0.25,0.198 10 false F 1.563,0.698 1.813,0.896 0.25,0.198 10 false E 3.073,0.375 3.323,0.573 0.25,0.198 10 false F 3.167,0.667 3.354,0.865 0.188,0.198 10 false E

Connect a GTS to the DLC3.


b.

Disconnect the vacuum hose (canister side) from the purge valve.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for EVAP Control.


f.

When the purge valve is operated using the GTS, check whether the port of the purge valve applies suction to your finger.

OK:
Tester Operation Specified Condition
VSV ON Purge valve port applies suction to finger
VSV OFF Purge valve port applies no suction to finger


Text in Illustration
*a Purge valve ON
*b Purge valve OFF

Result
Result Proceed to
NG A
OK B



A

2.INSPECT PURGE VALVE

B

7.CHECK HARNESS AND CONNECTOR (PURGE VALVE - EFI MAIN1 RELAY)
2.INSPECT PURGE VALVE

OK

3.INSPECT PURGE VALVE (POWER SOURCE)

NG

3.INSPECT PURGE VALVE (POWER SOURCE)
a.
U146755E03
0.771,1.01 1,1.198 0.229,0.188 10 false d1 0.177,0.083 0.542,0.281 0.365,0.198 10 false *a

Disconnect the purge valve connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
d1-1 - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Purge valve)


OK

4.CHECK HARNESS AND CONNECTOR (PURGE VALVE - ECM)

NG

6.INSPECT RELAY (EFI MAIN1)
4.CHECK HARNESS AND CONNECTOR (PURGE VALVE - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the purge valve connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A36-11 (PRG) - d1-2 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A36-11 (PRG) or d1-2 - Body ground Always 10 kΩ or higher




OK

5.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the tester on.


g.

Start the engine.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.


j.

Read DTCs.

Result
Result Proceed to
No DTC is output A
P0458 or P0459 is output B

HINT:

If the engine does not start, replace the ECM.




A

B

6.INSPECT RELAY (EFI MAIN1)

OK

7.CHECK HARNESS AND CONNECTOR (PURGE VALVE - EFI MAIN1 RELAY)

NG

REPLACE RELAY (EFI MAIN1)

7.CHECK HARNESS AND CONNECTOR (PURGE VALVE - EFI MAIN1 RELAY)
a.

Disconnect the purge valve connector.


b.

Remove the EFI MAIN1 relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
d1-1 - EFI MAIN1 relay terminal 3 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
d1-1 or EFI MAIN1 relay terminal 3 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR