Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM
RM2090E _51 Engine / Hybrid System _060673 CRUISE CONTROL _0297540 CRUISE CONTROL SYSTEM U

CRUISE CONTROL  CRUISE CONTROL SYSTEM  CANCEL CODE  


DESCRIPTION


The ECM stores cancellation of cruise control due to driver operation and system abnormality as a "CANCEL CODE". In troubleshooting, the "CANCEL CODE" can be used to specify the cause of the malfunction.

HINT:
·

The "CANCEL CODE" for canceled cruise control resulting from driver operation is also stored. Therefore, fault troubleshooting needs to determine whether the "CANCEL CODE" is due to driver operation or a system abnormality.

·

Storage of a "CANCEL CODE" due to the driver canceling cruise control is normal, and not a system abnormality.

·

The "CANCEL CODE" is cleared by turning off the ignition switch. So, does not turn the ignition switch off until the "CANCEL CODE" has been checked.




READ CANCEL CODE


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Perform a cruise control road test, and recreate the driving conditions in which cruise control was previously canceled.


e.

After cruise control is canceled, check the Data List (See page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST).


f.

Check the stored "CANCEL CODE".

*: "(MEMORY)" displays the storage history of the "CANCEL CODE", and is not deleted by turning the ignition switch off.

Cruise Cancel : Main Switch
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Main Switch Cruise control was canceled through a cruise control main switch operation or cruise control main switch signal abnormality. / ON or OFF
·

Operation of cruise control main switch

·

Cruise control main switch assembly malfunction

·

Cruise control main switch circuit malfunction


Troubleshooting:
1.

Confirm whether there has been a cruise control main switch operation.

2.

If it was stored resulting from other than a driver operation, refer to "Cruise Control Switch Circuit", and perform a check (See page (Click here)).



Cruise Cancel : Stop/Brake Switch
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Stop/Brake Switch Cruise control was canceled through a brake pedal operation or stop light switch signal abnormality. / ON or OFF
·

Brake pedal operation

·

Stop light switch assembly malfunction

·

Stop light switch circuit malfunction


Troubleshooting:
1.

Confirm whether there has been a brake pedal operation.

2.

If it was stored resulting from other than a driver operation, refer to "Stop Light Switch Circuit", and perform a check (See page (Click here)).



Cruise Cancel : Clutch Switch
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Clutch Switch Cruise control was canceled through a clutch pedal operation or clutch switch signal abnormality. / ON or OFF
·

Clutch pedal operation

·

Clutch switch assembly malfunction

·

Clutch switch circuit malfunction


Troubleshooting:
1.

Confirm whether there has been a clutch pedal operation.

2.

If it was stored resulting from other than a driver operation, refer to "Clutch Switch Circuit", and perform a check (See page (Click here)).



Cruise Cancel : Neutral Switch
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Neutral Switch Cruise control was canceled through a shift lever operation or park/neutral start switch signal abnormality. / ON or OFF
·

Shift lever operation

·

Park/neutral position switch assembly malfunction

·

Park/neutral position switch circuit malfunction


Troubleshooting:
1.

Confirm whether there has been a shift lever operation.

2.

If it was stored resulting from other than a driver operation, refer to DTC P0707 in ECT system, and perform a check (See page (Click here)).



Cruise Cancel : Cancel Switch
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Cancel Switch Cruise control was canceled through a CANCEL switch operation or CANCEL switch signal abnormality. / ON or OFF
·

CANCEL switch operation

·

Cruise control main switch assembly malfunction

·

Cruise control main switch circuit malfunction


Troubleshooting:
1.

Confirm whether there has been a CANCEL switch operation.

2.

If it was stored resulting from other than a driver operation, refer to "Cruise Control Switch Circuit", and perform a check (See page (Click here)).



Cruise Cancel : IG Switch
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : IG Switch Cruise control was canceled through an ignition switch operation or ECM power supply circuit abnormality. / ON or OFF
·

Ignition switch operation

·

ECM power supply circuit malfunction


Troubleshooting:
1.

Confirm whether there has been an ignition switch operation.

2.

If it was stored resulting from other than a driver operation, refer to "ECM Power Source Circuit", and perform a check (See page (Click here)).



Cruise Cancel : Vehicle Speed 1
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Vehicle Speed 1 Cruise control was canceled through a vehicle speed signal abnormality. / ON or OFF
·

Speed sensor malfunction

·

Skid control ECU (Brake actuator assembly) malfunction

·

ECM malfunction


Troubleshooting:
1.

Check the VSC system DTC (See page (Click here)).



Cruise Cancel : Engine Revolution
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Engine Revolution One of the following conditions is met:
·

Cruise control was canceled through detection of engine speed that is more than specified.

·

Cruise control was canceled through moving the shift lever to 1st or Reverse position. (for Manual Transmission)

·

Cruise control was canceled through moving the shift lever to 1st range with the shift lever in M or R range. (for Automatic Transmission)


/ ON or OFF
·

Shift lever operation

·

Crankshaft position sensor malfunction

·

ECM malfunction


Troubleshooting:
1.

Confirm whether there has been a shift lever operation.

2.

If it was stored resulting from other than a driver operation, refer to DTC P0335, and perform a check (See page (Click here)).



Cruise Cancel : Out of Range
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Out of Range One of the following conditions is met:
·

Cruise control was canceled through vehicle speed dropping below minimum cruise control speed.

·

Cruise control was canceled through setting the cruise control outside permitted vehicle speed.

·

Cruise control was canceled through a RESUME operation with no recorded vehicle speed.


/ ON or OFF
·

SET switch operation

·

RESUME switch operation

·

Speed sensor malfunction

·

Skid control ECU (Brake actuator assembly) malfunction


Troubleshooting:
1.

Confirm whether there has been a SET or RESUME operation.

2.

Perform a cruise control road test with a vehicle speed at 40km/h or more.

3.

If the "CANCEL CODE" is stored again, check the VSC system DTC (See page (Click here)).



Cruise Cancel : Accel Angle
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Accel Angle Cruise control was canceled through an accelerator pedal operation resulting in more than 10 minutes of set vehicle speed. / ON or OFF Accelerator pedal operation
Troubleshooting:
1.

Confirm whether there has been an accelerator pedal operation.



Cruise Cancel : Keeping Vehicle Speed
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Keeping Vehicle Speed Cruise control was canceled through an inability to maintain vehicle speed. / ON or OFF
·

Parking brake not released

·

Insufficient tire pressure

·

Road condition (inclination, road surface)


Troubleshooting:
1.

Confirm the road conditions (inclination, road surface) when the "CANCEL CODE" was stored.

2.

Check the vehicle status (parking brake, tire pressure).



Cruise Cancel : VSC/TRC Operation
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : VSC/TRC Operation Cruise control was canceled through a VSC/TRC operation. / ON or OFF VSC/TRC operation
Troubleshooting:
-

Cruise Cancel : ABS/VSC Abnormal
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : ABS/VSC Abnormal Cruise control was canceled through an ABS/VSC system abnormality / ON or OFF ABS/VSC system malfunction
Troubleshooting:
1.

Check the VSC system DTC (See page (Click here)).



Cruise Cancel : Meter Abnormal
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Meter Abnormal Cruise control was canceled through a combination meter assembly abnormality. / ON or OFF Combination meter assembly malfunction
Troubleshooting:
1.

Check the combination meter assembly (See page(Click here)).



Cruise Cancel : Brake Switch Abnormal
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Brake Switch Abnormal Cruise control was canceled through a stop light switch assembly abnormality. / ON or OFF Stop light switch assembly malfunction
Troubleshooting:
1.

Refer to "Stop Light Switch Circuit", and perform a check (See page (Click here)).



Cruise Cancel : Neutral Switch Abnormal
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Neutral Switch Abnormal Cruise control was canceled through a park/neutral position switch abnormality. / ON or OFF Park/neutral position switch assembly malfunction
Troubleshooting:
1.

Refer to DTC P0707 in ECT system, and perform a check (See page (Click here)).



Cruise Cancel : Vehicle Speed 2
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Vehicle Speed 2 Cruise control was canceled through a vehicle speed change abnormality. / ON or OFF
·

Speed sensor malfunction

·

Skid control ECU (Brake actuator assembly) malfunction


Troubleshooting:
1.

Check the VSC system DTC (See page (Click here)).



Cruise Cancel : Engine Abnormal
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Engine Abnormal Cruise control was canceled through an engine system abnormality. / ON or OFF Engine control system malfunction
Troubleshooting:
1.

Check the engine control system DTC (See page (Click here)).



Cruise Cancel : Switch Related to Cruise Control
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Switch Related to Cruise Control Cruise control was canceled through a cruise control main switch fixation (2 minutes or more continuous input). / ON or OFF Cruise control main switch assembly malfunction
Troubleshooting:
1.

Refer to "Cruise Control Switch Circuit", and perform a check (See page (Click here)).



Cruise Cancel : Brake Switch Abnormal(Memory)*
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Brake Switch Abnormal(Memory) "Cruise Cancel : Brake Switch Abnormal" is detected. / ON or OFF Stop light switch assembly malfunction
Troubleshooting:
1.

Refer to "Stop Light Switch Circuit", and perform a check (See page (Click here)).



Cruise Cancel : Neutral Switch Abnormal(Memory)*
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Neutral Switch Abnormal(Memory) "Cruise Cancel : Neutral Switch Abnormal" is detected. / ON or OFF Park/neutral position switch assembly malfunction
Troubleshooting:
1.

Refer to DTC P0707 in ECT system, and perform a check (See page (Click here)).



Cruise Cancel : Vehicle Speed 2(Memory)*
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Vehicle Speed 2(Memory) "Cruise Cancel : Vehicle Speed 2" is detected. / ON or OFF
·

Speed sensor malfunction

·

Skid control ECU (Brake actuator assembly) malfunction


Troubleshooting:
1.

Check the VSC system DTC (See page (Click here)).



Cruise Cancel : Engine Abnormal(Memory)*
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Engine Abnormal(Memory) "Cruise Cancel : Engine Abnormal" is detected. / ON or OFF Engine control system malfunction
Troubleshooting:
1.

Check the engine control system DTC (See page (Click here)).



Cruise Cancel : Switch Related to CCS(Memory)*
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : Switch Related to CCS(Memory) "Cruise Cancel : Switch Related to Cruise Control" is detected. / ON or OFF Cruise control main switch assembly malfunction
Troubleshooting:
1.

Refer to "Cruise Control Switch Circuit", and perform a check (See page (Click here)).



Cruise Cancel : ECT Abnormal
Tester Display Measurement Item/Range Trouble Area
Cruise Cancel : ECT Abnormal Cruise control was canceled through an automatic transmission system abnormality. / ON or OFF Automatic transmission system malfunction
Troubleshooting:
1.

Check the automatic transmission system DTC (See page (Click here)).