Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2016.06–2019.03
RM2090E _54 Brake _060684 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0297617 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  VSC OFF Indicator Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch turns off TRC and pressing and holding this switch turns off TRC and VSC. If VSC is turned off, the VSC OFF indicator light will come on.

WIRING DIAGRAM

C264068E08
5.49,4 7.094,4.521 1.604,0.521 10 false Skid Control ECU (Brake Actuator Assembly) 5.49,3.813 5.813,4.042 0.323,0.229 10 false A5 0.177,4.063 1.448,4.406 1.271,0.344 10 false Combination Meter Assembly 0.177,3.865 0.49,4.021 0.313,0.156 10 false D7 5.917,0.823 6.458,1.031 0.542,0.208 10 false CANL 5.917,1.448 6.51,1.74 0.594,0.292 10 false CANH 5.646,0.656 5.938,0.885 0.292,0.229 10 false 14 5.646,1.271 5.927,1.5 0.281,0.229 10 false 26 0.833,0.813 1.281,0.969 0.448,0.156 10 false CANL 0.833,1.448 1.281,1.604 0.448,0.156 10 false CANH 1.354,0.656 1.573,0.813 0.219,0.156 10 false 7 1.354,1.292 1.573,1.448 0.219,0.156 10 false 6 5.927,2.802 6.542,3.177 0.615,0.375 10 false CSW2 5.708,2.698 5.969,2.99 0.26,0.292 10 false 9 5.917,2.25 6.438,2.542 0.521,0.292 10 false CSW1 5.646,2.135 5.917,2.375 0.271,0.24 10 false 12 2.771,3.552 4.792,3.958 2.021,0.406 10 false Pattern Select Switch Assembly 3.25,2.948 4.229,3.125 0.979,0.177 10 false TRACK Switch 3.219,2.385 4.365,2.708 1.146,0.323 10 false VSC OFF Switch 2.771,3.365 3.083,3.521 0.313,0.156 10 false D35 4.771,2.688 5.01,2.927 0.24,0.24 10 false 1 4.771,2.104 4.979,2.333 0.208,0.229 10 false 5 2.688,2.708 2.906,2.865 0.219,0.156 10 false 8 2.781,4.344 4.75,4.719 1.969,0.375 10 false :CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
DTC is not output. A
DTC is output. B




A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.




OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V




OK

4.READ VALUE USING GTS (VSC OFF SWITCH)

NG

4.READ VALUE USING GTS (VSC OFF SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
TRC(TRAC)/VSC Off Mode TRC/VSC OFF mode / Normal, TRC(TRAC) OFF or VSC OFF Normal: Normal mode
TRC(TRAC) OFF: TRC OFF mode
VSC OFF: VSC OFF mode
-


d.

Using the GTS, check that the switch condition displayed on the GTS changes according to VSC OFF switch operation.

OK:

The GTS display changes according to VSC OFF switch operation.




OK

5.READ VALUE USING GTS (TRACK SWITCH)

NG

7.INSPECT VSC OFF SWITCH
5.READ VALUE USING GTS (TRACK SWITCH)
a.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
TRACK Mode TRACK mode / Normal or TRACK Normal: Normal mode
TRACK: TRACK mode
-


b.

Using the GTS, check that the switch condition displayed on the GTS changes according to TRACK switch operation.

OK:

The GTS display changes according to TRACK switch operation.




OK

6.INSPECT COMBINATION METER ASSEMBLY

NG

9.INSPECT TRACK SWITCH
6.INSPECT COMBINATION METER ASSEMBLY
a.

Perform an Active Test of the combination meter assembly (meter CPU) using the GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).


b.

Check the combination meter assembly.

OK:

The VSC OFF indicator and TRACK indicator lights turn on or off in accordance with the Active Test operation.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

NG

REPLACE COMBINATION METER ASSEMBLY

7.INSPECT VSC OFF SWITCH

OK

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)

NG

REPLACE PATTERN SELECT SWITCH ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)
a.

Disconnect the skid control ECU (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-12 (CSW1) - D35-5 Always Below 1 Ω
A5-12 (CSW1) - Body ground Always 10 kΩ or higher
D35-8 - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT TRACK SWITCH

OK

10.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - TRACK SWITCH)

NG

REPLACE PATTERN SELECT SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - TRACK SWITCH)
a.

Disconnect the skid control ECU (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-9 (CSW2) - D35-1 Always Below 1 Ω
A5-9 (CSW2) - Body ground Always 10 kΩ or higher
D35-8 - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR