Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2014.05
RM2090E _54 Brake _060684 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0297617 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1237  Speed Sensor Rotor Faulty  C1275  Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1276  Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1277  Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1278  Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)  


DESCRIPTION

The skid control ECU (brake actuator assembly) measures the speed of each wheel by receiving signals from the speed sensor.

These signals are used for recognizing that all four wheels are operating properly.

Therefore, all wheel signals must be equal.

DTCs C1275 to C1278 are cleared when the speed sensor sends a vehicle speed signal or when Test Mode ends. DTCs C1275 to C1278 are output only in Test Mode.

DTC No. DTC Detection Condition Trouble Area
C1237 Any of the following is detected:
1.

Discrepancy among four wheel speed sensor output.

2.

Abnormal pulse signals from 3 or more sensors.

3.

Continuous ABS control is performed for 60 seconds or more.

4.

VSC control is performed for 5 seconds or more.


·

Tire and wheel size

·

Tire deformation

·

Speed sensor rotor

·

Speed sensor

·

Speed sensor circuit

·

Skid control ECU


C1275
C1276
Detected only during Test Mode. Front speed sensor rotor RH/LH (Front axle hub sub-assembly RH/LH)
C1277
C1278
Detected only during Test Mode. Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH)

HINT:
·

DTC C1275 is for the front speed sensor RH.

·

DTC C1276 is for the front speed sensor LH.

·

DTC C1277 is for the rear speed sensor RH.

·

DTC C1278 is for the rear speed sensor LH.



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


HINT:

When C1330, C1331, C1332, C1333, C1464, C1465, C1466 and/or C1467 is output together with C1237, inspect and repair the trouble areas indicated by C1330, C1331, C1332, C1333, C1464, C1465, C1466 and/or C1467 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1271 for front, and/or Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1273 for rear).


PROCEDURE

1.CHECK TIRES
a.

Check the size and condition of all four wheels (See page Suspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION).

HINT:

The DTC is output when tire deformation or a difference in tire size is detected.


OK:

The diameter of all four tires and the tire pressure are the same.




OK

2.READ VALUE USING GTS (SPEED SENSOR)

NG

REPLACE TIRES SO THAT ALL FOUR TIRES ARE THE SAME SIZE

2.READ VALUE USING GTS (SPEED SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations


d.

Check the speed value output from the speed sensor displayed on the GTS.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.


Result:
Result Proceed to
OK A
NG (for front) B
NG (for rear) C




A

3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

B

5.CHECK FRONT SPEED SENSOR INSTALLATION

C

13.CHECK REAR SPEED SENSOR INSTALLATION
3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Perform the sensor check using the Test Mode procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).

OK:

All Test Mode DTCs are not output.


Result:
Result Proceed to
OK A
NG (for front) B
NG (for rear) C




A

4.RECONFIRM DTC

B

5.CHECK FRONT SPEED SENSOR INSTALLATION

C

13.CHECK REAR SPEED SENSOR INSTALLATION
4.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1237 is not output. A
DTC C1237 is output (for front). B
DTC C1237 is output (for rear). C




A

B

9.REPLACE FRONT SPEED SENSOR

C

17.REPLACE REAR SPEED SENSOR
5.CHECK FRONT SPEED SENSOR INSTALLATION
a.
C168336E24
1.031,0.833 1.24,0.646 false 0.948,1.49 1.271,1.677 false 0.115,0.104 0.813,0.406 0.698,0.302 10 false *1 1.271,0.5 1.51,0.74 0.24,0.24 10 false *c 1.323,1.583 1.563,1.823 0.24,0.24 10 false *d 0.719,1.802 0.958,2.042 0.24,0.24 10 false *a 2.438,1.875 2.677,2.115 0.24,0.24 10 false *b

Turn the ignition switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the steering knuckle.

The installation bolt is tightened properly.

Torque:

7.5 N*m (76 kgf*cm, 66 in.*lbf)


Text in Illustration
*1 Front Speed Sensor
*a Correct
*b Incorrect
*c 7.5 N*m
*d No clearance



OK

6.CHECK FRONT SPEED SENSOR TIP

NG

6.CHECK FRONT SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

No scratches or foreign matter on the sensor tip.


NOTICE:

Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




OK

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)

b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the skid control ECU (brake actuator assembly) connector and the front speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
A5-16 (FR+) - A42-2 (FR+) Always Below 1 Ω
A5-16 (FR+) - Body ground Always 10 kΩ or higher
A5-4 (FR-) - A42-1 (FR-) Always Below 1 Ω
A5-4 (FR-) - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
A5-19 (FL+) - A12-2 (FL+) Always Below 1 Ω
A5-19 (FL+) - Body ground Always 10 kΩ or higher
A5-8 (FL-) - A12-1 (FL-) Always Below 1 Ω
A5-8 (FL-) - Body ground Always 10 kΩ or higher




OK

8.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.RECONFIRM DTC
a.

Reconnect the skid control ECU (brake actuator assembly) connector and the front speed sensor connector.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1237 is output. A
DTC C1237 is not output. B




A

9.REPLACE FRONT SPEED SENSOR

B

9.REPLACE FRONT SPEED SENSOR
a.

Turn the ignition switch off.


b.

Replace the front speed sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL).

NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




NEXT

10.RECONFIRM DTC
10.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.



Result:
Result Proceed to
DTC C1237 is output. A
DTC C1237 is not output. B



A

11.REPLACE FRONT SPEED SENSOR ROTOR

B

END

11.REPLACE FRONT SPEED SENSOR ROTOR
a.

Turn the ignition switch off.


b.

Replace the front speed sensor rotor (See page Drivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL).

HINT:

If the front speed sensor rotor needs to be replaced, replace the front axle hub sub-assembly.


NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




NEXT

12.RECONFIRM DTC
12.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.



Result:
Result Proceed to
DTC C1237 is output. A
DTC C1237 is not output. B



A

B

END

13.CHECK REAR SPEED SENSOR INSTALLATION
a.
C168336E24
1.031,0.833 1.24,0.646 false 0.948,1.49 1.271,1.677 false 0.115,0.104 0.813,0.406 0.698,0.302 10 false *1 1.271,0.5 1.51,0.74 0.24,0.24 10 false *c 1.323,1.583 1.563,1.823 0.24,0.24 10 false *d 0.719,1.802 0.958,2.042 0.24,0.24 10 false *a 2.438,1.875 2.677,2.115 0.24,0.24 10 false *b

Turn the ignition switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle carrier sub-assembly.

The installation bolt is tightened properly.

Torque:

7.5 N*m (76 kgf*cm, 66 in.*lbf)


Text in Illustration
*1 Rear Speed Sensor
*a Correct
*b Incorrect
*c 7.5 N*m
*d No clearance



OK

14.CHECK REAR SPEED SENSOR TIP

NG

14.CHECK REAR SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

No scratches or foreign matter on the sensor tip.


NOTICE:

Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




OK

15.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)

NG

CLEAN OR REPLACE REAR SPEED SENSOR

15.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)

b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU (brake actuator assembly) connector and the rear speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
A5-17 (RR+) - G9-2 (RR+) Always Below 1 Ω
A5-17 (RR+) - Body ground Always 10 kΩ or higher
A5-29 (RR-) - G9-1 (RR-) Always Below 1 Ω
A5-29 (RR-) - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
A5-31 (RL+) - H12-2 (RL+) Always Below 1 Ω
A5-31 (RL+) - Body ground Always 10 kΩ or higher
A5-18 (RL-) - H12-1 (RL-) Always Below 1 Ω
A5-18 (RL-) - Body ground Always 10 kΩ or higher




OK

16.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.RECONFIRM DTC
a.

Reconnect the skid control ECU (brake actuator assembly) connector and the rear speed sensor connector.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1237 is output. A
DTC C1237 is not output. B




A

17.REPLACE REAR SPEED SENSOR

B

17.REPLACE REAR SPEED SENSOR
a.

Turn the ignition switch off.


b.

Replace the rear speed sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL).

NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




NEXT

18.RECONFIRM DTC
18.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.



Result:
Result Proceed to
DTC C1237 is output. A
DTC C1237 is not output. B



A

19.REPLACE REAR SPEED SENSOR ROTOR

B

END

19.REPLACE REAR SPEED SENSOR ROTOR
a.

Turn the ignition switch off.


b.

Replace the rear speed sensor rotor (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL).

HINT:

If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly.


NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




NEXT

20.RECONFIRM DTC
20.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.



Result:
Result Proceed to
DTC C1237 is output. A
DTC C1237 is not output. B



A

B

END