The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
If any of the following is detected, the brake warning light remains on:
The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).
The brake fluid level is insufficient.
The parking brake is applied.
EBD operation is not possible.
When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check if a CAN communication system DTC is output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| DTC is not output. | A |
| DTC is output. | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check if the skid control ECU (brake actuator assembly) connector is securely connected.
The connector is securely connected.
OK
NG
Check the battery voltage.
11 to 14 V
OK
NG
w/ 150 A Generator
w/ 130 A Generator
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A5-25 (+BS) - Body ground | Always | 11 to 14 V |
| A5-25 (+BS) - A5-38 (GND1) | Always | 11 to 14 V |
| A5-28 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| A5-28 (IG1) - A5-38 (GND1) | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
OK
NG
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A5-38 (GND1) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
OK
NG
Reconnect the skid control ECU (brake actuator assembly) connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Select the Data List using the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Parking Brake SW | Parking brake switch / ON or OFF | ON: Parking brake applied
OFF: Parking brake released |
- |
Using the GTS, check the switch operation signal received when the parking brake is operated.
When the parking brake is operated, the display changes as shown above.
OK
NG
Turn the ignition switch off.
Remove the reservoir filler cap and the strainer.
Disconnect the brake fluid level warning switch connector.
Measure the resistance according to the value(s) in the table below.
A float is located inside the reservoir. Its position changes according to the brake fluid level.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Switch OFF (Float up) | 1.9 to 2.1 kΩ |
| 1 - 2 | Switch ON (Float down) | Below 1 Ω |
| *a | Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Sub-assembly)) |
If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D7-17 (LBL) - A59-1 | Always | Below 1 Ω |
| D7-17 (LBL) - Body ground | Always | 10 kΩ or higher |
| A59-2 - Body ground | Always | Below 1 Ω |
OK
NG
Reconnect the combination meter assembly connector and the brake fluid level warning switch connector.
Perform an Active Test of the combination meter assembly (meter CPU) using the GTS.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST
Check the combination meter assembly.
The brake warning light turns on or off in accordance with the Active Test operation.
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.
OK
NG
Turn the ignition switch off.
Disconnect the parking brake switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - Body ground | Parking brake switch ON
(Switch pin free) |
Below 1 Ω |
| 1 - Body ground | Parking brake switch OFF
(Switch pin pushed in) |
10 kΩ or higher |
| *a | Component without harness connected
(Parking Brake Switch Assembly) |
OK
NG
Disconnect the instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-24 - D31-1 | Always | Below 1 Ω |
| 3B-24 - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MB-14 (PKB) - 3B-24 | Always | Below 1 Ω |
| MB-14 (PKB) - Body ground | Always | 10 kΩ or higher |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.
OK
NG