Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.08
RM19Y0E _57 Power Source / Network _003004 NETWORKING _0015181 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the V bus main lines and/or CAN branch lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω.
·

Short in CAN main bus line

·

Short in CAN branch line

·

ECM

·

Skid control ECU (brake actuator assembly)

·

Main body ECU (fuse block assembly)

·

Airbag ECU assembly

·

Power steering ECU assembly

·

Combination switch ECU (switch base)

·

Combination meter assembly

·

No. 1 CAN junction connector



WIRING DIAGRAM

C329974E02
0.292,6.083 1.833,6.521 1.542,0.438 10 false Airbag ECU Assembly 0.302,5.906 0.688,6.156 0.385,0.25 10 false E76 0.719,7.729 1.104,7.979 0.385,0.25 10 false DLC3 0.719,7.563 1.104,7.813 0.385,0.25 10 false E12 0.677,8.396 2.563,8.76 1.885,0.365 10 false : CAN Main Bus Line (CANH) 0.677,8.729 2.563,9.094 1.885,0.365 10 false : CAN Main Bus Line (CANL) 0.677,9.073 2.563,9.438 1.885,0.365 10 false : CAN Branch Line (CANH) 0.677,9.417 2.573,9.76 1.896,0.344 10 false : CAN Branch Line (CANL) 0.677,8.073 2.115,8.438 1.438,0.365 10 false : Suspected Area 2.896,5.063 3.167,5.344 0.271,0.281 10 false 1 2.844,5.635 3.115,5.917 0.271,0.281 10 false 12 2.896,6.813 3.167,7.094 0.271,0.281 10 false 4 2.844,7.344 3.115,7.625 0.271,0.281 10 false 15 4.427,5.823 4.698,6.104 0.271,0.281 10 false 2 4.406,6.396 4.677,6.677 0.271,0.281 10 false 13 4.427,7.427 4.698,7.708 0.271,0.281 10 false 5 4.406,7.969 4.677,8.25 0.271,0.281 10 false 16 4.125,8.25 4.396,8.531 0.271,0.281 10 false 9 3.125,8.26 3.396,8.542 0.271,0.281 10 false 20 4.125,4.74 4.396,5.021 0.271,0.281 10 false 8 3.115,4.729 3.385,5.01 0.271,0.281 10 false 19 5.833,8.427 7.115,9.115 1.281,0.688 10 false Combination Switch ECU (Switch Base) 5.844,8.271 6.229,8.521 0.385,0.25 10 false E68 5.135,6.729 5.521,6.979 0.385,0.25 10 false E75 5.135,6.885 7.125,7.26 1.99,0.375 10 false Power Steering ECU Assembly 4.458,5.073 6.563,5.448 2.104,0.375 10 false No. 1 CAN Junction Connector 4.448,4.906 4.833,5.156 0.385,0.25 10 false E87 5.365,2.958 6.5,3.344 1.135,0.385 10 false Main Body ECU 4.771,1.396 5.156,1.646 0.385,0.25 10 false A24 4.771,1.573 5.156,1.823 0.385,0.25 10 false ECM 0.24,1.469 0.625,1.719 0.385,0.25 10 false A13 0.24,1.646 1.802,2.354 1.563,0.708 10 false Skid Control ECU (Brake Actuator Assembly) 4.156,1.521 4.75,1.865 0.594,0.344 10 false HCAN 2.896,1.542 3.49,1.885 0.594,0.344 10 false LCAN 2.781,1.177 3.375,1.521 0.594,0.344 10 false CANL 2.771,0.604 3.365,0.948 0.594,0.344 10 false CANH 1.135,0.604 1.729,0.948 0.594,0.344 10 false CANH 1.146,1.188 1.74,1.531 0.594,0.344 10 false CANL 1.115,5.052 1.708,5.396 0.594,0.344 10 false CANH 1.135,5.635 1.729,5.979 0.594,0.344 10 false CANL 1.354,6.917 1.948,7.26 0.594,0.344 10 false CANH 1.24,7.24 1.833,7.583 0.594,0.344 10 false CANL 5.906,7.417 6.5,7.76 0.594,0.344 10 false CANH 5.917,7.99 6.51,8.333 0.594,0.344 10 false CANL 5.917,5.823 6.51,6.167 0.594,0.344 10 false CANH 5.927,6.396 6.521,6.74 0.594,0.344 10 false CANL 4.135,2.823 4.729,3.167 0.594,0.344 10 false CANH 2.896,2.833 3.49,3.177 0.594,0.344 10 false CANL 3.5,0.375 4.073,0.677 0.573,0.302 10 false 120 Ω 3.51,9.313 4.083,9.615 0.573,0.302 10 false 120 Ω 4.75,9.406 6.781,9.792 2.031,0.385 10 false Combination Meter Assembly 4.75,9.24 5.135,9.49 0.385,0.25 10 false E34 1.854,4.99 2.167,5.292 0.313,0.302 10 false Y 2.542,5.698 2.854,6 0.313,0.302 10 false GR 5.042,5.75 5.354,6.052 0.313,0.302 10 false SB 5.052,6.469 5.365,6.771 0.313,0.302 10 false BR 2.229,6.75 2.667,7.052 0.438,0.302 10 false G-W 2.26,7.427 2.698,7.698 0.438,0.271 10 false L-W 4.167,8.469 4.479,8.771 0.313,0.302 10 false W 3.125,8.458 3.438,8.76 0.313,0.302 10 false P 4.167,4.521 4.479,4.823 0.313,0.302 10 false BE 3.083,4.531 3.396,4.833 0.313,0.302 10 false W 5.083,7.354 5.396,7.656 0.313,0.302 10 false G 5.083,8.042 5.396,8.344 0.313,0.302 10 false B 4.125,4.292 4.396,4.573 0.271,0.281 10 false 17 3.115,4.292 3.385,4.573 0.271,0.281 10 false 16 4.125,2.156 4.396,2.438 0.271,0.281 10 false 21 3.115,2.167 3.385,2.448 0.271,0.281 10 false 30 4.167,1.969 4.479,2.271 0.313,0.302 10 false GR 3.073,1.958 3.385,2.26 0.313,0.302 10 false W 1.844,6.823 2.115,7.104 0.271,0.281 10 false 6 1.646,7.354 1.917,7.635 0.271,0.281 10 false 14 2.531,1.177 2.802,1.458 0.271,0.281 10 false 40 2.531,0.615 2.802,0.896 0.271,0.281 10 false 39 4.115,1.76 4.385,2.042 0.271,0.281 10 false 25 3.115,1.76 3.385,2.042 0.271,0.281 10 false 26 2.083,1.24 2.396,1.542 0.313,0.302 10 false G 2.104,0.542 2.417,0.844 0.313,0.302 10 false R 4.135,8.667 4.406,8.948 0.271,0.281 10 false 9 3.177,8.667 3.448,8.948 0.271,0.281 10 false 8 4.146,8.896 4.74,9.24 0.594,0.344 10 false CANH 2.885,8.896 3.479,9.24 0.594,0.344 10 false CANL 1.594,0.604 1.865,0.885 0.271,0.281 10 false 22 1.583,1.177 1.854,1.458 0.271,0.281 10 false 10 1.583,5.063 1.854,5.344 0.271,0.281 10 false 26 1.583,5.635 1.854,5.917 0.271,0.281 10 false 25 1.833,5.708 2.146,6.01 0.313,0.302 10 false W 2.604,4.99 2.917,5.292 0.313,0.302 10 false Y 5.729,6.406 6,6.688 0.271,0.281 10 false 1 5.74,5.823 6.01,6.104 0.271,0.281 10 false 5 5.729,7.427 6,7.708 0.271,0.281 10 false 8 5.729,7.99 6,8.271 0.271,0.281 10 false 7 3.99,4.083 4.375,4.333 0.385,0.25 10 false 3G 3.99,2.365 4.375,2.615 0.385,0.25 10 false 3C 3.24,2.365 3.625,2.615 0.385,0.25 10 false 3C 3.219,4.083 3.604,4.333 0.385,0.25 10 false 3G 0.094,0.073 1.073,0.438 0.979,0.365 12 false V Bus: 5.104,4.083 6.844,4.521 1.74,0.438 10 false Fuse Block Assembly 4.146,3.635 4.74,3.979 0.594,0.344 10 false CANH 2.896,3.635 3.49,3.979 0.594,0.344 10 false CANL

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 60 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS LINES (ECM - MAIN BODY ECU (FUSE BLOCK ASSEMBLY))
a.

Disconnect the cable from the negative (-) battery terminal.


b.
A348485C07
1.5,0.25 1.917,0.5 0.417,0.25 0.969,0.958 0.969,0.125 0.969,0.125 1.135,0.125 true 0.844,0.948 0.844,0.365 0.844,0.365 0.677,0.365 true 0.094,0.104 0.385,0.385 0.292,0.281 10 false *a 1.583,0.292 2.01,0.563 0.427,0.271 10 false A24 0.281,0.292 0.781,0.542 0.5,0.25 10 false LCAN 1.198,0.052 1.698,0.302 0.5,0.25 10 false HCAN
*a Front view of wire harness connector
(to ECM)


Disconnect the A24 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-25 (HCAN) - A24-26 (LCAN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK FOR SHORT IN CAN BUS LINES (ECM - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))

NG

4.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY - NO. 1 CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT IN CAN BUS LINES (ECM - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
a.
A348485C08
1.469,0.229 1.885,0.479 0.417,0.25 0.948,1.146 0.844,0.417 0.844,0.417 0.677,0.417 true 0.844,1.271 0.75,1.958 0.75,1.958 0.583,1.958 true 0.094,0.104 0.385,0.385 0.292,0.281 10 false *a 1.552,0.26 1.979,0.531 0.427,0.271 10 false A24 0.25,0.344 0.75,0.594 0.5,0.25 10 false CANH 0.177,1.875 0.667,2.115 0.49,0.24 10 false CANL
*a Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-39 (CANH) - A24-40 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result Proceed to
OK (for 1NR-VE) A
OK (for 2NR-VE) B
NG C



A

B

C

3.CHECK FOR SHORT IN CAN BUS LINES (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - ECM)
3.CHECK FOR SHORT IN CAN BUS LINES (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - ECM)
a.

Reconnect the A24 ECM connector.


b.
C330019C16
1.51,0.25 1.927,0.5 0.417,0.25 2.292,0.323 2.125,0.323 2.125,0.323 2.021,0.99 true 2.417,1.917 2.25,1.917 2.25,1.917 2.01,1.219 true 0.115,0.094 0.427,0.344 0.313,0.25 10 false *a 1.594,0.292 1.99,0.583 0.396,0.292 10 false A13 2.479,1.833 2.99,2.135 0.51,0.302 10 false CANH 2.365,0.26 2.875,0.563 0.51,0.302 10 false CANL
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-22 (CANH) - A13-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - ECM)

4.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY - NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the A24 ECM connector.


b.
E208723C04
1.49,0.271 1.906,0.521 0.417,0.25 1.375,1.125 1.083,0.417 1.083,0.417 0.917,0.417 true 1.552,1.104 2.25,0.417 2.25,0.417 2.417,0.417 true 0.115,0.104 0.448,0.396 0.333,0.292 10 false *a 1.573,0.313 1.906,0.604 0.333,0.292 10 false E34 2.5,0.333 3,0.625 0.5,0.292 10 false CANH 0.5,0.344 1,0.635 0.5,0.292 10 false CANL
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the E34 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E34-9 (CANH) - E34-8 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

5.CHECK FOR SHORT IN CAN BUS LINES (MAIN BODY ECU (FUSE BLOCK ASSEMBLY))
5.CHECK FOR SHORT IN CAN BUS LINES (MAIN BODY ECU (FUSE BLOCK ASSEMBLY))
a.

Reconnect the E34 combination meter assembly connector.


b.
C329970C03
1.521,2.667 1.938,2.917 0.417,0.25 1.469,0.448 1.885,0.698 0.417,0.25 2.052,1.271 2.406,0.531 2.406,0.531 2.573,0.531 true 2.042,1.51 2.323,2.052 2.323,2.052 2.49,2.052 true 1.865,3.823 2.094,4.396 2.094,4.396 2.26,4.396 true 1.719,3.823 1.469,4.375 1.469,4.375 1.302,4.375 true 0.125,0.135 0.458,0.406 0.333,0.271 10 false *a 1.583,0.49 2,0.771 0.417,0.281 10 false 3C 1.635,2.708 2.052,2.99 0.417,0.281 10 false 3G 2.313,4.313 3.042,4.594 0.729,0.281 10 false CANH*c 2.635,0.458 3.271,0.802 0.635,0.344 10 false CANH*b 2.542,1.979 3.146,2.302 0.604,0.323 10 false CANL*b 0.76,4.281 1.417,4.594 0.656,0.313 10 false CANL*c
*a Front view of wire harness connector
(to Main Body ECU (Fuse Block Assembly))
*b to ECM
*c to No. 1 CAN Junction Connector


Disconnect the 3C and 3G main body ECU (fuse block assembly) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
3C-21 (CANH) - 3C-30 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM
3G-17 (CANH) - 3G-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 1 CAN junction connector



Result:
Result Proceed to
OK (for RHD) A
OK (for LHD) B
NG (ECM main line) C
NG (No. 1 CAN junction connector main line) D



A

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

B

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - ECM)

D

6.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
6.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the 3C and 3G main body ECU (fuse block assembly) connectors.


b.
C248060C22
0.083,1.417 0.5,1.667 0.417,0.25 1.333,1.51 1,0.26 1,0.26 0.833,0.26 true 2.083,1.51 2.333,0.51 2.333,0.51 2.5,0.51 true 0.771,1.521 0.521,0.771 0.521,0.771 0.354,0.771 true 0.969,1.51 0.635,0.51 0.635,0.51 0.469,0.51 true 1.531,1.51 1.865,0.26 1.865,0.26 2.031,0.26 true 2.25,1.51 2.583,0.76 2.583,0.76 2.75,0.76 true 2.271,1.917 2.604,2.5 2.604,2.5 2.771,2.5 true 2.083,1.917 2.333,2.75 2.333,2.75 2.5,2.75 true 1.531,1.917 1.865,3 1.865,3 2.031,3 true 1.333,1.917 1.083,3 1.083,3 0.917,3 true 0.969,1.917 0.802,2.667 0.802,2.667 0.635,2.667 true 0.75,1.917 0.583,2.417 0.583,2.417 0.417,2.417 true 0.115,0.104 0.417,0.375 0.302,0.271 10 false *a 0.135,0.677 0.563,1.042 0.427,0.365 10 false *b 0.167,1.458 0.656,1.792 0.49,0.333 10 false E87 0.292,0.417 0.719,0.781 0.427,0.365 10 false *c 0.625,0.177 1.052,0.542 0.427,0.365 10 false *d 2.094,0.167 2.521,0.531 0.427,0.365 10 false *e 2.573,0.427 3,0.792 0.427,0.365 10 false *f 2.813,0.667 3.24,1.031 0.427,0.365 10 false *g 0.219,2.333 0.646,2.698 0.427,0.365 10 false *b 0.438,2.583 0.865,2.948 0.427,0.365 10 false *c 0.719,2.917 1.146,3.281 0.427,0.365 10 false *d 2.094,2.917 2.521,3.281 0.427,0.365 10 false *e 2.573,2.677 3,3.042 0.427,0.365 10 false *f 2.833,2.406 3.26,2.771 0.427,0.365 10 false *g
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Airbag ECU Assembly
*c to Power Steering ECU Assembly
*d to DLC3
*e to Combination Switch ECU (Switch Base)
*f to Main Body ECU (Fuse Block Assembly)
*g to Combination Meter Assembly


Disconnect the E87 No. 1 CAN junction connector connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
E87-1 (CANH) - E87-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airbag ECU assembly
E87-2 (CANH) - E87-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Power steering ECU assembly
E87-4 (CANH) - E87-15 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher DLC3
E87-5 (CANH) - E87-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Combination switch ECU (switch base)
E87-8 (CANH) - E87-19 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Main body ECU (fuse block assembly)
E87-9 (CANH) - E87-20 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly



Result:
Result Proceed to
OK A
NG (ECU or sensor branch line) B
NG (DLC3 branch line) C
NG (main body ECU (fuse block assembly) main line) D
NG (Combination meter assembly main line) E



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

7.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)

C

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

D

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - MAIN BODY ECU (FUSE BLOCK ASSEMBLY))

E

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

7.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
E231257C41
1.458,0.26 1.865,0.51 0.406,0.25 2.5,0.417 2.333,0.417 2.333,0.417 2,0.917 true 1.583,1.833 1.75,1.833 1.75,1.833 1.917,1.469 true 0.104,0.094 0.5,0.417 0.396,0.323 10 false *1 2.583,0.344 3.167,0.667 0.583,0.323 10 false CANH 1.156,1.76 1.573,2.01 0.417,0.25 10 false CANL 1.542,0.302 2.042,0.635 0.5,0.333 10 false E12
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E12-6 (CANH) - E12-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Proceed to
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINE OR CONNECTOR