Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › CAMSHAFT › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _059913 2ZR-FXE ENGINE MECHANICAL _0293918 CAMSHAFT A

2ZR-FXE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during camshaft removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
for SFI system
·

Replacement of throttle body assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of ignition coil assembly


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

PROCEDURE

Hide 51441 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 2.DRAIN ENGINE COOLANT (for Engine)

Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55737B 4.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 55735A 5.REMOVE WATER GUARD PLATE LH

Hide 55736D 6.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735C 7.REMOVE COWL BODY MOUNTING REINFORCEMENT RH

Hide 55701J 8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 9.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 33820B 10.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
A393200

Remove the bolt to disconnect the transmission control cable assembly from the cylinder head cover sub-assembly.


Hide 12262 11.DISCONNECT NO. 2 VENTILATION HOSE

Hide 11101E 13.REMOVE CAMSHAFT POSITION SENSOR

Hide 82121 14.DISCONNECT ENGINE WIRE

a.
A380543

Disconnect the 3 connectors.


b.

Disengage the 4 clamps.


c.

Remove the bolt and disconnect the engine wire from the cylinder head cover sub-assembly.


Hide 23826 15.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

Hide 16296 17.DISCONNECT NO. 8 WATER BY-PASS HOSE

Hide 16297 18.DISCONNECT NO. 9 WATER BY-PASS HOSE

Hide 17650G 19.REMOVE PURGE VALVE (PURGE VSV)

Hide 23818 20.REMOVE FUEL VAPOR FEED PIPE

Hide 11201 21.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11213 22.REMOVE CYLINDER HEAD COVER GASKET

Hide 11193 23.REMOVE SPARK PLUG TUBE GASKET

Hide 24.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

a.

Set the No. 1 cylinder to TDC (Compression).

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY


b.
A377938C01
0.938,0.823 2.792,0.365 true 2.781,0.885 2.792,0.365 2.792,0.365 2.99,0.948 true 0.927,1.01 1.75,1.667 1.75,1.667 2.958,1.125 true 2.729,0.167 3.042,0.323 0.313,0.156 10 true *a 1.646,1.708 1.958,1.865 0.313,0.156 10 true *b
*a Paint Mark
*b Timing Mark


Place paint marks on the chain sub-assembly in alignment with the timing marks on the camshaft timing gear assembly and camshaft timing sprocket.


Hide 13562 25.REMOVE NO. 2 CHAIN VIBRATION DAMPER

a.
A375421N01
1.865,1.458 2.615,0.656 true 2.667,0.583 3.125,0.781 0.458,0.198 10 false SST

Using SST, remove the 2 bolts and No. 2 chain vibration damper from the No. 1 camshaft bearing cap.

SST
09961-00950  


Hide 13540 26.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13523G 27.REMOVE CAMSHAFT TIMING SPROCKET

a.
A375422C01
2.458,0.25 2.667,0.25 false 2.521,0.76 2.677,0.5 2.677,0.5 2.792,0.5 false 2.729,0.167 3.188,0.365 0.458,0.198 10 false SST 2.833,0.385 3.146,0.583 0.313,0.198 10 false *a 1.167,0.167 1.479,0.365 0.313,0.198 10 true *b 0.479,0.188 0.698,0.396 0.219,0.208 10 true *c
*a 14 mm union nut wrench
*b Hold
*c Turn


While holding the hexagonal portion of the No. 2 camshaft with a wrench, remove the bolt with SST and 14 mm union nut wrench.

SST
09961-00950  


b.
A375423

While removing the chain sub-assembly, pull out the camshaft timing sprocket horizontally and then upward.


Hide 13050 28.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

Hide 29.REMOVE CAMSHAFT BEARING CAP

a.
A375427N01
0.969,0.5 1.125,0.698 0.156,0.198 10 true 1 0.938,1.438 1.094,1.635 0.156,0.198 10 true 2 1.573,0.5 1.729,0.698 0.156,0.198 10 true 5 1.552,1.542 1.708,1.74 0.156,0.198 10 true 6 2.115,0.479 2.271,0.677 0.156,0.198 10 true 9 2.094,1.542 2.323,1.76 0.229,0.219 10 true 10 2.635,0.469 2.792,0.667 0.156,0.198 10 true 7 2.625,1.521 2.781,1.719 0.156,0.198 10 true 8 3.156,0.448 3.313,0.646 0.156,0.198 10 true 3 3.146,1.542 3.302,1.74 0.156,0.198 10 true 4

Uniformly loosen and remove the 10 bolts in the order shown in the illustration.

NOTICE:

Do not loosen the other 10 bearing cap bolts in this step.


HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



b.

Remove the bolts and camshaft bearing caps in the order shown in the illustration. Immediately after removing each camshaft bearing cap, install service bolts and spacers in the order shown in the illustration.

A375428C01
1.521,1.396 1.979,0.917 1.979,0.917 1.521,1.073 true 4.438,3.052 4.75,3.208 0.313,0.156 10 false *a 4.438,3.271 4.75,3.427 0.313,0.156 10 false *b 2.042,0.823 2.354,0.979 0.313,0.156 10 false *c
*a The removal order of the parts *b The installation order of the service bolts and spacers for temporarily tightening the camshaft housing sub-assembly
*c Service bolt and spacer (Used to temporarily secure the camshaft housing sub-assembly) - -


Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)

NOTICE:
·

If the bolts are loosened all at once, seal packing on the camshaft housing sub-assembly and cylinder head sub-assembly may separate, resulting in oil leaks. Therefore, be sure to install the service bolts and spacers to one camshaft bearing cap at a time.

·

Do not install the camshaft bearing caps when installing the service bolts and spacers.



HINT:
·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.

·

Part number for the service bolt used to temporarily secure the camshaft housing sub-assembly: 91551-G0875 (15 bolts)

·

Part number for the spacer used to temporarily secure the camshaft housing sub-assembly: 90387-12048 (15 spacers)




Hide 13512 30.REMOVE NO. 2 CAMSHAFT

a.
A375429

Remove the No. 2 camshaft from the camshaft housing sub-assembly.


Hide 13511 31.REMOVE CAMSHAFT

a.
A375430

Hold up the chain sub-assembly and remove the camshaft from the camshaft housing sub-assembly.


b.
A375431

Suspend the chain sub-assembly with a string or equivalent.


Hide 13050 32.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.

Secure the hexagonal portion of the camshaft in a soft jaw vise.


b.
A375432C01
1.021,1.104 0.563,1.146 0.563,1.146 1.24,0.938 true 1.229,1.552 0.583,1.156 0.583,1.156 1.417,1.375 true 0.365,1.083 0.677,1.24 0.313,0.156 10 false *a
*a Do not remove


Remove the bolt and camshaft timing gear assembly.

NOTICE:
·

Before removing the camshaft timing gear assembly, make sure that the lock pin has been released.

·

Do not remove the other 4 bolts.

·

Keep the camshaft timing gear assembly horizontal while removing it from the camshaft.

·

If the camshaft timing gear assembly is to be reused, be sure to install it with the lock pin released.