Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294918 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1430  Brake Pedal Load Sensing Switch OFF Stuck Malfunction  C1431  Brake Pedal Load Sensing Switch ON Stuck Malfunction  


DESCRIPTION

The brake pedal load sensing switch turns on when the brake pedal is depressed with a force exceeding a predetermined level.

The skid control ECU uses this circuit to detect if the brake pedal is depressed or not.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1430 Brake Pedal Load Sensing Switch OFF Stuck Malfunction Either of the following is detected:
1.

With the stop light switch on, the brake pedal load sensing switch off, and the master cylinder pressure more than 6 MPa (61.2 kgf/cm2, 870 psi), the vehicle acceleration rate is less than -4 m/s2 for 1 second or more.

2.

With the stop light switch on, the brake pedal load sensing switch off, and the master cylinder pressure more than 6 MPa (61.2 kgf/cm2, 870 psi), the vehicle speed is 0 km/h (0 mph) for 5 seconds or more.


·

Brake pedal load sensing switch (Brake pedal support assembly)

·

Brake pedal load sensing switch circuit


C1431 Brake Pedal Load Sensing Switch ON Stuck Malfunction Either of the following is detected:
1.

With the stop light switch off, the brake pedal load sensing switch on, and the master cylinder pressure less than 0.7 MPa (7.13 kgf/cm2, 101 psi), the vehicle acceleration rate is more than -0.8 m/s2 for 10 seconds or more. (Only when the engine is running and booster malfunctions are not detected.)

2.

Condition which the brake pedal load sensing switch remains on while the vehicle speed increases from 0 km/h (0 mph) to 30 km/h (19 mph) occurs 5 times in succession.


·

Brake pedal load sensing switch (Brake pedal support assembly)

·

Brake pedal load sensing switch circuit



DTC Detection Conditions: C1430
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status With the stop light switch on, the brake pedal load sensing switch off, and the master cylinder pressure more than 6 MPa (61.2 kgf/ cm2, 870 psi), the vehicle acceleration rate is less than -4 m/s2. ○ -
With the stop light switch on, the brake pedal load sensing switch off, and the master cylinder pressure more than 6 MPa (61.2 kgf/ cm2, 870 psi), the vehicle speed is 0 km/h (0 mph). - ○
Detection Time 1 second or more 5 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1431
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status With the stop light switch off, the brake pedal load sensing switch on, and the master cylinder pressure less than 0.7 MPa (7.13 kgf/cm2, 101 psi), the vehicle acceleration rate is more than -0.8 m/s2. (Only when the engine is running and booster malfunctions are not detected.) ○ -
Condition which the brake pedal load sensing switch remains on while the vehicle speed increases from 0 km/h (0 mph) to 30 km/h (19 mph) occurs 5 times in succession. - ○
Detection Time 10 seconds or more -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

HINT:

When C1249, C1425 and/or C1426 is output together with C1430 and/or C1431, inspect and repair the trouble areas indicated by C1249, C1425 and/or C1426 first (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1249), Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425), and/or Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1426)).


PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY AND BRAKE PEDAL LOAD SENSING SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Brake Pedal Load Sensing SW Brake pedal load sensing switch ON or OFF ON: Brake pedal depressed beyond as pecified point
OFF: Brake pedal not depressed beyond as pecified point
-

d.

Check that the stop light switch display and brake pedal load sensing switch display observed on the GTS change according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



e.

Slowly depress the brake pedal, and check when the stop light switch and brake pedal load sensing switch turn on.

OK:

First the stop light switch turns on, and then the brake pedal load sensing switch turns on.



Result:
Result Proceed to
OK A
NG (Turning on of the brake pedal load sensing switch is not confirmed.) B
NG (The brake pedal load sensing switch turns on first.) C



A

2.RECONFIRM DTC

B

3.INSPECT BRAKE PEDAL LOAD SENSING SWITCH

C

5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
2.RECONFIRM DTC
a.

Turn the ignition switch off.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.



Result:
Result Proceed to
DTCs C1430 and C1431 are not output. A
DTCs C1430 and C1431 are output. (for LHD) B
DTCs C1430 and C1431 are output. (for RHD) C



A

END

B

C

3.INSPECT BRAKE PEDAL LOAD SENSING SWITCH
a.
C239141C13
1.563,2.021 0.979,2.823 true 1.823,2.021 2.406,2.823 true 0.271,0.229 0.479,0.417 0.208,0.188 10 false *a 0.688,2.875 1.146,3.063 0.458,0.188 10 false FSW+ 2.25,2.875 2.708,3.063 0.458,0.188 10 false FSW-
*a Component without harness connected
(Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A63 brake pedal load sensing switch connector.

NOTICE:
·

Do not remove the brake pedal load sensing switch from the brake pedal support assembly.

·

When there is a malfunction in the brake pedal load sensing switch, replace the brake pedal support assembly.




d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (FSW+) - 1 (FSW-) Switch OFF
(Brake pedal depressed)
950 to 1050 Ω
2 (FSW+) - 1 (FSW-) Switch ON
(Brake pedal released)
203 to 223 Ω



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL LOAD SENSING SWITCH)

B

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

C

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL LOAD SENSING SWITCH)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-17 (FSW+) -A63-2 (FSW+) Always Below 1 Ω
A42-17 (FSW+) - Body ground Always 10 kΩ or higher
A63-2 (FSW+) -Body ground Always 10 kΩ or higher
A63-1 (FSW-) -Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.



c.

Check the stop light switch assembly installation.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

OK:

The brake pedal height and stop light switch assembly installation are normal.



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

B

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

C

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY

D

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY