Home › Drivetrain › K313 (MULTIDRIVE / CVT) › TRANSMISSION CONTROL CABLE › 2016.10–2020.08
RM32H0E _52 Drivetrain _059624 K313 MULTIDRIVE / CVT _0299314 TRANSMISSION CONTROL CABLE A

K313 MULTIDRIVE / CVT  TRANSMISSION CONTROL CABLE  INSTALLATION  


PROCEDURE

Hide 33820B 1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C365142

Pass the transmission control cable assembly into the vehicle and install the transmission control cable assembly to the vehicle body with the 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.
C365141

Engage the guide to connect the transmission control cable assembly to vehicle body.


c.

Install the nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.
C329707N01
2.531,0.417 2.688,0.615 0.156,0.198 10 true N 2.823,0.938 2.979,1.135 0.156,0.198 10 true P

Turn the control shaft lever clockwise until it stops, and then from that position turn it counterclockwise by 2 notches to set it to the N position.


e.

Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


f.

Connect the transmission control cable assembly to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


g.

for TMMT Made:

i.
C366437C01
0,0 0,0 false
V113147

Install in this Direction


Connect the transmission control cable assembly to the floor shift shift lever assembly.

NOTICE:

Make sure that the transmission control cable assembly is securely locked.



ii.
C366436C02
0,0 0,0 false
V113147

Install in this Direction


Connect the end of the transmission control cable assembly to the floor shift shift lever assembly.

NOTICE:
·

Before connecting the transmission control cable assembly, check that the park/neutral position switch and shift lever are in N.

·

Install the end of the transmission control cable assembly so that the lock piece faces the driver side.

·

Install the end of the transmission control cable assembly all the way to the base of the pin.





h.

for TMC Made:

i.
C288539C01
2.24,0.906 2.552,0.708 false 1,1.875 1.313,1.677 false 0.854,1.781 1.167,1.938 0.313,0.156 10 false *1 2.594,0.604 2.906,0.76 0.313,0.156 10 false *2
*1 Nut
*2 Lock
V100135

Rotate approximately 180°
V100136

Push in


Rotate the nut of the transmission control cable assembly approximately 180° in the direction shown in the illustration, and while holding the nut in that position, push in the lock.

NOTICE:

Rotating the nut too much will damage the internal spring, and the transmission control cable assembly will not be reusable. Do not turn the nut too far.



ii.
C365195C01
0.792,2.531 0.604,2.344 false 2.813,2.542 2.625,2.354 false 2.458,2.26 2.771,2.417 0.313,0.156 10 false *1 0.458,2.229 0.771,2.385 0.313,0.156 10 false *a 0.313,2.5 0.5,2.656 0.188,0.156 10 false A 1.24,2.51 1.427,2.667 0.188,0.156 10 false A
*1 Lock
*a Protrusion
V113147

Install in this Direction


Install the transmission control cable assembly to the floor shift shift lever assembly.

NOTICE:
·

Install the transmission control cable assembly with the protrusion facing upwards.

·

After installation, make sure that the lock is projecting from A as shown in the illustration.

·

Make sure that the transmission control cable assembly is securely locked.




iii.
C365194C01
0,0 0,0 false
V113147

Install in this Direction


Confirm that the shift lever is in N, and then connect the end of the transmission control cable assembly to the floor shift shift lever assembly.

NOTICE:
·

Securely install the end of the transmission control cable assembly to the floor shift shift lever assembly.

·

Install the end of the transmission control cable assembly so that its adjustment lock section is on the driver side.





Hide 58151 3.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

a.

Install the front No. 1 floor heat insulator to the vehicle body with the 2 bolts and nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 17410 4.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 17701 8.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17705 9.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 17751 10.INSTALL NO. 1 AIR CLEANER INLET

Hide 53141F 11.INSTALL RADIATOR COVER

Hide 12.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 33504F 13.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

Hide 28800 14.INSTALL BATTERY

Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>8NR-FTS BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 17.INSPECT FOR EXHAUST GAS LEAK

Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>EXHAUST PIPE (for 2WD)>INSTALLATION

HINT:

Perform "Inspection After Repairs" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION