Home › Drivetrain › EC69 (MANUAL TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE › 2016.10–2019.09
RM32H0E _52 Drivetrain _060311 EC69 MANUAL TRANSMISSION / TRANSAXLE _0303337 TRANSMISSION CONTROL CABLE A

EC69 MANUAL TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the transmission control cable assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point
·

Lane departure alert system (w/ Steering Control)

·

Simple intelligent parking assist system*1

·

Toyota parking assist-sensor system (w/ Simple Intelligent Parking Assist System)

·

Pre-collision system


(Click here)
Initialize back door lock Power door lock control system (Click here)
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)


CAUTION:
·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



PROCEDURE

Hide 1.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
·
C332327

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to neutral, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>8NR-FTS BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 28800 4.REMOVE BATTERY

Hide 5.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 53141F 6.REMOVE RADIATOR COVER

Hide 17751 7.REMOVE NO. 1 AIR CLEANER INLET

Hide 17705 8.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 17701 9.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 57533B 12.REMOVE FRONT FLOOR CENTER BRACE

Hide 17410 13.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 58151 14.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

a.
C364049

Remove 3 nuts and front No. 1 floor heat insulator from the vehicle body.


Hide 33820B 15.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C365818

Remove the clip to disconnect the transmission control select cable from the floor shift shift lever assembly.


b.
C365819

Disconnect the transmission control shift cable from the floor shift shift lever assembly.


c.
C365820

Disengage the 2 claws and disconnect the transmission control cable assembly from the floor shift lever assembly.


d.
C356470N01
1.708,1.438 1.865,1.635 0.156,0.198 10 true A 1.51,1.938 1.667,2.135 0.156,0.198 10 true A 2.344,0.5 2.5,0.698 0.156,0.198 10 true B 1.104,0.052 1.26,0.25 0.156,0.198 10 true B

Remove the 2 clips A to disconnect the transmission control cable assembly from the manual transaxle assembly.


e.

Remove the 2 clips B to disconnect the transmission control cable assembly from the control cable bracket assembly.


f.
C365821

Remove the nut.


g.

Disengage the guide and disconnect the transmission control cable assembly from the vehicle body.


h.
C365822

Remove the 2 nuts and transmission control cable assembly from the vehicle body.