Home › Drivetrain › EC69 (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE ASSEMBLY (When Using the Engine Support Bridge) › 2016.10–2019.09
RM32H0E _52 Drivetrain _060311 EC69 MANUAL TRANSMISSION / TRANSAXLE _0303343 MANUAL TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge) A

EC69 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the manual transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point
·

Lane departure alert system (w/ Steering Control)

·

Simple intelligent parking assist system*1

·

Toyota parking assist-sensor system (w/ Simple Intelligent Parking Assist System)

·

Pre-collision system


(Click here)
Initialize back door lock Power door lock control system (Click here)
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Front wheel alignment adjustment Perform the following procedures in the order shown:
1.

Clear zero point calibration data and store system information

2.

Perform yaw rate and acceleration sensor zero point calibration and store system information


·

VSC disabled or malfunctions

·

DTCs are stored

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)


CAUTION:
·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the transmission jack


Because the manual transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the transmission jack could drop and components could fall down.


·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



NOTICE:

When the manual transaxle assembly is removed, be sure to use a new clutch release cylinder with bearing assembly and new installation bolts. Removal of the manual transaxle assembly allows the compressed clutch release cylinder with bearing assembly to return to its original position. Dust from the moving section may damage the seal of the clutch release cylinder with bearing assembly, possibly causing clutch fluid leaks.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>8NR-FTS BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 4.REMOVE FRONT WHEELS

Hide 51441 5.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51444A 6.REMOVE REAR ENGINE UNDER COVER LH

Hide 51443C 7.REMOVE REAR ENGINE UNDER COVER RH

Hide 10.DRAIN MANUAL TRANSAXLE OIL

Hide 11.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55737B 12.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 55735A 13.REMOVE WATER GUARD PLATE LH

Hide 55736D 14.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735C 15.REMOVE COWL BODY MOUNTING REINFORCEMENT RH

Hide 55701J 16.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 17.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 28800 18.REMOVE BATTERY

Hide 53141F 19.REMOVE RADIATOR COVER

Hide 17751 20.REMOVE NO. 1 AIR CLEANER INLET

Hide 21.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17701 22.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 24.REMOVE BATTERY CLAMP SUB-ASSEMBLY

a.
A390461

Remove the bolt and nut to separate the engine wire from the battery clamp sub-assembly.


b.
A392287

Disengage the clamp to separate the engine wire from the battery clamp sub-assembly.


c.

Remove the 3 bolts and battery clamp sub-assembly from the vehicle.


Hide 33820B 25.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C356470N01
1.708,1.438 1.865,1.635 0.156,0.198 10 true A 1.51,1.938 1.667,2.135 0.156,0.198 10 true A 2.344,0.5 2.5,0.698 0.156,0.198 10 true B 1.104,0.052 1.26,0.25 0.156,0.198 10 true B

Remove the 2 clips A to disconnect the transmission control cable assembly from the manual transaxle assembly.


b.

Remove the 2 clips B to disconnect the transmission control cable assembly from control cable bracket assembly.


Hide 45100 26.SECURE STEERING WHEEL ASSEMBLY

Hide 45259A 27.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 28.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45025D 29.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 57533B 30.REMOVE FRONT FLOOR CENTER BRACE

Hide 17410 31.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 32.DISCONNECT WIRE HARNESS

a.
C366688C01
3,2.813 3.219,3.01 0.219,0.198 10 true *1 1.271,2.333 1.49,2.531 0.219,0.198 10 true *2
*1 Back-up Light Switch Assembly Connector
*2 Transmission Revolution Sensor Connector


Disconnect the back-up light switch assembly connector.


b.

Disconnect the transmission revolution sensor connector.


c.

Remove the bolt.


d.

Disengage the clamp and separate the wire harness from the manual transaxle assembly.


e.
C366690

Disengage the 3 clamps and separate the heated oxygen sensor wire harness from the front suspension crossmember sub-assembly.


f.
C366691

Disconnect the neutral position switch connector.


g.

Disengage the 3 clamps and separate the wire harness from the manual transaxle assembly.


Hide 31481A 33.DISCONNECT NO. 1 CLUTCH HOSE

a.
C356488

Using a 10 mm union nut wrench, disconnect the bleeder clutch release tube from the No. 1 clutch hose.


b.

Remove the clip to disconnect the No. 1 clutch hose.


Hide 12321B 34.REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

Hide 35.REMOVE FRONT DRIVE SHAFT ASSEMBLY (for TMC Made)

Hide 36.REMOVE FRONT DRIVE SHAFT ASSEMBLY (for TMMT Made)

Hide 37.INSTALL ENGINE HANGERS

a.
A392293

Disconnect the wire harness from the wire harness clamp bracket.


b.

Disengage the 3 clamps from the wire harness clamp bracket.


c.

Remove the nut to separate the engine wire from the wire harness clamp bracket.


d.

Remove the bolt and wire harness clamp bracket from the cylinder head sub-assembly.


e.
C364032

Separate the bolts and No. 2 earth wire from the engine mounting insulator sub-assembly RH.


f.
A351514C03
0.406,1.604 0.75,1.604 true 2.531,1.073 2.875,1.073 true 0.219,1.542 0.531,1.698 0.313,0.156 10 false *1 2.958,1.01 3.271,1.167 0.313,0.156 10 true *2 0.052,0.052 0.365,0.208 0.313,0.156 10 false *a 1.677,0.042 1.99,0.198 0.313,0.156 10 false *b
*1 No. 1 Engine Hanger (Part No. 12281-47060)
*2 No. 2 Engine Hanger (Part No. 12282-47030)
*a Front of Engine (or RH Side of Vehicle)


Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 38.INSTALL ENGINE SUPPORT BRIDGE

a.
C364030

Remove the clip and the neck from the windshield washer jar assembly.


b.

Install SST to the vehicle body as shown in the illustration.

C365148C01
5.875,3.156 6.313,2.979 false 4.427,6.156 5.094,6.156 true 1.99,6.073 2.333,6.25 true 4.417,5 5.323,5.333 true 1.781,5.24 2.667,5.083 true 1.25,1.333 1.833,1.042 true 5.333,1.417 4.896,1.115 true 4.198,4.865 4.417,5.063 0.219,0.198 10 true *a 4.188,6.063 4.417,6.25 0.229,0.188 10 true *b 5.344,1.333 5.563,1.531 0.219,0.198 10 true *c 6.354,2.875 6.698,3.042 0.344,0.167 10 false SST 2.354,6.177 2.583,6.365 0.229,0.188 10 true *b 2.688,4.969 2.906,5.167 0.219,0.198 10 true *a 1.031,1.26 1.25,1.458 0.219,0.198 10 true *c
*a Support Shaft *b Front Side Member
*c Front Suspension Nut - -


SST
09940-10020  

CAUTION:
·
C330755C01
0.448,1.167 0.781,1.167 false 2.438,1.167 2.771,1.167 false 1.052,1.781 1.052,1.448 1.052,1.448 1.219,1.448 false 2.604,1.781 2.604,1.448 2.604,1.448 2.438,1.448 false 0.292,1.094 0.604,1.25 0.313,0.156 10 false *a 2.271,1.094 2.583,1.25 0.313,0.156 10 false *a 1.281,1.385 1.594,1.542 0.313,0.156 10 false *b 2.271,1.385 2.583,1.542 0.313,0.156 10 false *b
*a Support Shaft
*b Front Side Member


Make sure that no oil or grease is on the front side member, and set the support shaft on the level surface of the front side member.

·

The engine support bridge may fall off if any oil or grease is still on or it is installed on the unlevel surface.



NOTICE:
·

Prevent SST from contacting the vehicle body exterior and windshield glass.

·

To prevent damage to the engine hood, place pieces of cloth between the engine hood and SST.

·

Lightly shake SST by hand to make sure it is securely installed before performing work.




c.
C338947C01
0.615,1.479 0.615,0.656 0.615,0.656 0.5,0.656 false 1.042,2.125 1.667,2.125 false 1.031,2.469 2.167,2.469 false 0.875,2.771 0.875,2.458 0.875,2.458 0.76,2.458 false 1.708,2.01 2.063,2.281 0.354,0.271 10 false *a 0.292,0.552 0.604,0.823 0.313,0.271 10 false *b 0.552,2.354 0.917,2.583 0.365,0.229 10 false *c 2.208,2.375 2.563,2.667 0.354,0.292 10 false *d
*a Support Shaft
*b Sub Beam
*c Front Side Member
*d Threaded Portion


Turn the threaded portion of each support shaft to adjust its height until the sub beams are parallel to the ground.


d.

Install the chain block to the sling bracket.

C365149C01
1.583,1 1.917,1 false 0.313,0.604 1.313,0.604 true 0.802,1.573 1.302,1.573 true 0.833,1.167 1.292,1.469 false 1.948,0.896 2.125,1.083 0.177,0.188 10 false *a 0.125,0.5 0.302,0.677 0.177,0.177 10 true *b 0.646,1.01 0.833,1.198 0.188,0.188 10 true *c 0.615,1.469 0.792,1.646 0.177,0.177 10 true *d
*a Chain Block *b Sling Bracket
*c Fuse Shackle *d Shackle (A)



e.

Install the division bar to the chain block with the shackles.

CAUTION:
·
C338949C01
0.458,2.313 0.583,2.313 0.583,2.313 0.875,2.635 false 0.354,2.677 0.479,2.677 0.479,2.677 0.865,2.865 false 2.177,2.271 2.302,2.271 2.302,2.271 2.604,2.594 false 2.073,2.656 2.198,2.656 2.198,2.656 2.583,2.844 false 0.281,2.208 0.604,2.469 0.323,0.26 10 false *a 0.167,2.573 0.51,2.844 0.344,0.271 10 false *b 1.99,2.156 2.313,2.417 0.323,0.26 10 false *a 1.885,2.542 2.229,2.813 0.344,0.271 10 false *b
*a Fuse Shackle
*b Shackle (A)


Make sure the fuse shackle is on the chain block side and the shackle (A) is on the division bar side as shown in the illustration so that the fuse bolt is visible and can be checked for deformation easily.

·

If the fuse shackle is installed upside down, deformation of the fuse bolt will not be visible and cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with automatic transaxle assembly may fall.

·
C330757C01
2.75,1 3.083,1 false 1.01,1 1.344,1 false 0.917,1.417 1.333,1.583 true 2.635,1.396 3.083,1.583 true 1.396,0.917 1.708,1.073 0.313,0.156 10 false *a 1.385,1.51 1.698,1.667 0.313,0.156 10 false *b 3.125,0.917 3.354,1.083 0.229,0.167 10 false *a 3.135,1.5 3.354,1.667 0.219,0.167 10 false *b
*a Fuse Shackle
*b Fuse Bolt


Make sure that the fuse bolt of the fuse shackle is free of damage, such as deformation or cracks. If damaged, replace the fuse shackle.

·

If a deformed fuse bolt is used, it cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with transaxle assembly may fall.




f.

Connect the division bar to the No. 1 engine hanger with the shackle (A) and chain.

C365150C01
2.25,4.042 2.25,3.542 true 1.667,4 1.26,3.75 true 1.052,3.927 0.583,3.75 true 0.875,4.458 0.458,4.458 true 1.75,1 1.302,1.271 true 0.5,1.708 0.5,1.292 true 1.323,1.49 1,1.583 true 2.198,1.604 1.74,1.76 true 0.219,4.354 0.406,4.531 0.188,0.177 10 true *1 2.25,1.531 2.438,1.719 0.188,0.188 10 true *2 2.156,4.052 2.365,4.24 0.208,0.188 10 true *a 1.688,3.917 1.885,4.115 0.198,0.198 10 true *b 0.375,3.615 0.573,3.802 0.198,0.188 10 true *c 0,0.781 0.156,0.938 0.156,0.156 10 false - 1.76,0.885 1.958,1.083 0.198,0.198 10 true *b 0.802,1.5 1,1.688 0.198,0.188 10 true *c 0.406,1.708 0.615,1.896 0.208,0.188 10 true *a
*1 No. 1 Engine Hanger *2 No. 2 Engine Hanger
*a Division Bar *b Shackle (A)
*c Chain - -



g.

Connect the division bar to the No. 2 engine hanger with the shackle (A) and chain.

NOTICE:

Connect the 2nd link of the chain to the No. 2 engine hanger.



h.
C330764C02
1.219,0.792 1.531,0.948 0.313,0.156 10 false *a
*a 120 mm (4.72 in.) or more


Make sure the distance between the chain block assembly and suspension ring is 120 mm (4.72 in.) or more.

HINT:

If the suspension height is less than 120 mm, adjust the links of the chain which connect the division bar and engine hanger.



i.

Adjust the positions of the chain block assembly, support brackets and main beam so that the chain of the chain block assembly is perpendicular to the main beam and the length of the main beam on the outer side of the support bracket LH and RH is the same as shown in the illustration.

C365151C01
3.5,1.5 4,1.5 true 4.25,0.958 4.75,0.583 false 4.01,1.396 4.229,1.594 0.219,0.198 10 true *a 4.76,0.438 5.073,0.594 0.313,0.156 10 false *b 6.115,0.427 6.427,0.583 0.313,0.156 10 false *c 1,0.406 1.313,0.563 0.313,0.156 10 false *d 3.198,0.344 3.51,0.5 0.313,0.156 10 false *e 0.979,2.333 1.146,2.5 0.167,0.167 10 true *f 6.135,2.365 6.302,2.531 0.167,0.167 10 true *f
*a Chain Block *b Main Beam
*c Dimension (A) *d Dimension (B)
*e Right to Left Adjustment *f Front to Rear Adjustment


CAUTION:
·

To prevent the engine with automatic transaxle assembly from falling, make sure that the length of dimension (A) and dimension (B) are equal.

·
C365152C01
2.01,1.49 2.302,1.125 false 2.271,0.948 2.583,1.104 0.313,0.156 10 false *a
*a Main Beam


Do not perform any procedures if the length of dimension (A) and dimension (B) are not equal.

·

Performing any procedure when the length of dimension (A) and dimension (B) are not equal may cause the engine assembly with automatic transaxle assembly and engine support bridge to fall, possibly causing serious injury.




j.

Confirm the appropriate installation state of the engine support bridge and tighten the 6 wing bolts and 2 bolts.

C365154C01
2.469,1.052 2.667,1.229 0.198,0.177 10 true *a 1.281,1.708 1.479,1.885 0.198,0.177 10 true *b 1.76,1.021 1.958,1.198 0.198,0.177 10 true *a 2.063,0.042 2.26,0.219 0.198,0.177 10 false *a 4.844,0.042 5.042,0.219 0.198,0.177 10 false *a 4.396,1.031 4.594,1.208 0.198,0.177 10 true *a 5.104,1.042 5.302,1.219 0.198,0.177 10 true *a 5.552,1.604 5.75,1.781 0.198,0.177 10 true *b
*a Wing Bolt *b Bolt


Torque:
Bolt : 30 N*m (306 kgf*cm, 22 ft.*lbf)

CAUTION:
·
C330761

Do not perform any procedures before tightening the bolts to the specified torque.

·

Performing procedures without tightening the bolts to the specified torque, may cause the engine support bridge to fall.




k.
C365155C01
2.656,3.125 2.854,3.333 0.198,0.208 10 true *a
*a Turn


Tighten the chain block assembly until it cannot be moved any further by hand.

CAUTION:
C330770C01
2.99,2.292 3.302,2.448 0.313,0.156 10 false *a
*a 41 N*m (418 kgf*cm, 30 ft.*lbf) or more


·

When suspending the engine with automatic transaxle assembly, do not tighten the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf).

·

Tightening the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf) will cause the load capacity (400 kg (881.8 lb)) to be exceeded and may cause damage to the engine support bridge and vehicle body.




Hide 51108A 39.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 40.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

Hide 51201 41.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 12364B 42.REMOVE NO. 2 ENGINE MOVING CONTROL ROD

a.
C366699

Remove the 4 bolts and No. 2 engine moving control rod from the manual transaxle assembly.


Hide 30300 43.SUPPORT MANUAL TRANSAXLE ASSEMBLY

a.
C366700C01
0.917,1.531 1.625,0.99 true 0.719,1.458 1.031,1.656 0.313,0.198 10 false *a
*a Lashing Belt


Using a transmission jack, support the manual transaxle assembly.

NOTICE:
·

Adjust the attachment of the transmission jack to securely fix the manual transaxle assembly to the transmission jack.

·

Using a lashing belt or a rope, fix the manual transaxle assembly to the transmission jack.




Hide 11363A 45.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 30300 46.REMOVE MANUAL TRANSAXLE ASSEMBLY

a.
C366701

Remove the bolt and nut to separate the transverse engine engine mounting insulator from the engine mounting bracket LH.

HINT:

Turn the bolt while holding the nut.



b.
C366702

Remove the nut, 4 bolts and transverse engine engine mounting insulator from the vehicle body.


c.
C366703

Remove the 5 bolts and engine mounting bracket LH from the manual transaxle assembly.


d.
C356495C01
0.25,1.5 0.396,1.323 false 0.5,1.917 0.813,1.823 false 2.74,1.833 2.49,1.667 false 2.833,0.969 2.583,0.802 false 2.427,0.708 2.74,0.906 0.313,0.198 10 false *a 2.938,1.5 3.167,1.667 0.229,0.167 10 false *b 2.802,1.813 3.031,1.979 0.229,0.167 10 false *2 0.344,1.865 0.573,2.031 0.229,0.167 10 false *1 0.125,1.521 0.354,1.688 0.229,0.167 10 false *a
*1 Engine Assembly
*2 Manual Transaxle Assembly
*a Vehicle Body
*b Tilt 50 mm (1.97 in.) or less
V100145

Watch for Interference


Operate the engine lifter and transmission jack, and slowly tilt the engine assembly with the manual transaxle assembly 50 mm (1.97 in.) or less.

NOTICE:
·

Do not allow the engine assembly and manual transaxle assembly to interfere with the vehicle body.

·

Make sure that the engine assembly is not tilted more than necessary.

·

Make sure that the wire harness and hoses are not being pulled.




e.
C187765E01
2.26,0.031 2.417,0.229 0.156,0.198 10 false A 1.177,0.042 1.333,0.24 0.156,0.198 10 false A 0.74,0.854 0.896,1.052 0.156,0.198 10 true B 1.073,1.76 1.229,1.958 0.156,0.198 10 true B 2.5,1.854 2.656,2.052 0.156,0.198 10 false B 2.052,1.958 2.24,2.146 0.188,0.188 10 false B 1.438,2.01 1.615,2.177 0.177,0.167 10 false B

Remove the 7 bolts and engine assembly from the manual transaxle assembly.

HINT:
·

Bolt (A): Remove from manual transaxle assembly side.

·

Bolt (B): Remove from engine assembly side.




f.
C356496C01
1.354,1.781 1.771,1.365 true 1.594,1.896 1.813,1.49 true 2.01,1.865 1.917,1.292 true 1.125,1.802 1.344,2 0.219,0.198 10 false *1 1.448,1.896 1.688,2.083 0.24,0.188 10 false *2 1.948,1.906 2.188,2.125 0.24,0.219 10 false *3
*1 Clutch Disc Assembly
*2 Clutch Cover Assembly
*3 Input Shaft


Using the transmission jack, remove the manual transaxle assembly from the engine assembly according to the procedures shown in the illustration.

NOTICE:
·

To prevent damage to the knock pins, do not pry between the manual transaxle assembly and engine assembly.

·

To prevent damage to the input shaft, do not forcefully shake the manual transaxle assembly.

·

Make sure the manual transaxle assembly does not interfere with the clutch tube or other components.



i.

Move the manual transaxle assembly towards the left side of the vehicle and disengage the input shaft from the clutch disc assembly.


ii.

Tilt the manual transaxle assembly and pull the input shaft out from the clutch cover assembly.


iii.

Lower the manual transaxle assembly.



Hide 31483 47.REMOVE BLEEDER CLUTCH RELEASE TUBE

Hide 31484 48.REMOVE CLUTCH FLEXIBLE HOSE BRACKET

a.
C356498

Remove the bolt and clutch flexible hose bracket from the manual transaxle assembly.


Hide 31407B 49.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 31400 50.REMOVE CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

Hide 51.REMOVE WIRE HARNESS CLAMP BRACKET

C366692

a.

Remove the bolt and wire harness clamp bracket from the manual transmission case.


Hide 87101A 52.REMOVE NO. 1 HEATER BRACKET SUB-ASSEMBLY

a.
C366689

Remove the bolt and No. 1 heater bracket sub-assembly from the manual transmission case.


Hide 335A0 53.REMOVE CONTROL CABLE BRACKET ASSEMBLY

a.
C366698

Remove the 3 bolts and control cable bracket assembly from the manual transmission case.


Hide 54.REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY

a.
C200883

Remove the bolt and speedometer driven hole cover sub-assembly from the manual transaxle assembly.


b.

Remove the O-ring from the speedometer driven hole cover sub-assembly.