Home › Drivetrain › EC69 (MANUAL TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE › 2016.10–2019.09
RM32H0E _52 Drivetrain _060311 EC69 MANUAL TRANSMISSION / TRANSAXLE _0303337 TRANSMISSION CONTROL CABLE A

EC69 MANUAL TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  INSTALLATION  


PROCEDURE

Hide 33820B 1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Pass the transmission control cable assembly into the vehicle and install the transmission control cable assembly to the vehicle body with the 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Engage the guide and connect the transmission control cable assembly to the vehicle body.


c.

Install the nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.
C356470C01
2.063,0.74 2.344,0.229 2.344,0.229 1.677,0.344 true 1.708,1.438 1.865,1.635 0.156,0.198 10 true A 1.51,1.938 1.667,2.135 0.156,0.198 10 true A 2.344,0.5 2.5,0.698 0.156,0.198 10 true B 1.104,0.052 1.26,0.25 0.156,0.198 10 true B 2.438,0.146 2.594,0.344 0.156,0.198 10 true *a
*a Paint Mark


Install the transmission control cable assembly to the control cable bracket assembly with 2 new clips B.

NOTICE:

Make sure that the paint marks on the transmission control cable assembly are aligned with the slits in the control cable bracket assembly before installing the clips.



e.

Connect the transmission control cable assembly to the manual transaxle assembly with the 2 clips A.


f.
C272829C04
0.052,0.073 3.365,2.135 3.313,2.063 0.073,2.583 3.365,4.469 3.292,1.885 1.094,0.917 1.25,0.635 1.25,0.635 1.417,0.635 false 1.448,1.844 1.448,1.583 false 0.521,1.865 0.521,1.604 false 0.521,4.135 0.521,3.875 false 1.469,4.115 1.469,3.854 false 1.458,0.563 1.771,0.719 0.313,0.156 10 false *1 0.458,1.875 0.771,2.031 0.313,0.156 10 false *2 1.385,1.875 1.698,2.031 0.313,0.156 10 false *3 2.719,0.469 3.031,0.625 0.313,0.156 10 false *a 0.802,0.365 1.115,0.521 0.313,0.156 10 false *b 2.646,2.698 2.958,2.854 0.313,0.156 10 false *c 0.479,4.156 0.792,4.313 0.313,0.156 10 false *2 1.417,4.135 1.729,4.292 0.313,0.156 10 false *3
*1 Lock Piece
*2 Stopper
*3 Adjuster Case
*a Twist the stopper
*b Pull out
*c Return the stopper


Release the lock of the transmission control select cable length adjustment structure.

i.

Twist the stopper.


ii.

Pull the lock piece outward from the adjuster case to release the lock.


iii.

Return the stopper.



g.

Engage the 2 claws to connect the transmission control cable assembly to the floor shift lever assembly.


h.

Connect the transmission control shift cable to the floor shift lever assembly.


i.
C365818

Connect the transmission control select cable to the floor shift lever assembly and install the clip.

NOTICE:
·

Make sure that the lock piece of the transmission control select cable length adjustment structure is facing upward when the transmission control select cable is connected.

·

Make sure that the transmission control select cable is securely installed.




Hide 33820B 2.ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 58151 3.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

a.

Install the front No. 1 floor heat insulator to the vehicle body with the 3 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 17410 4.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 17701 8.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17705 9.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 17751 10.INSTALL NO. 1 AIR CLEANER INLET

Hide 53141F 11.INSTALL RADIATOR COVER

Hide 12.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 28800 13.INSTALL BATTERY

Hide 14.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>8NR-FTS BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 15.INSPECT FOR EXHAUST GAS LEAK

Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>EXHAUST PIPE (for 2WD)>INSTALLATION

HINT:

Perform "Inspection After Repairs" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION