Home › Drivetrain › EC69 (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE ASSEMBLY (When Using the Engine Support Bridge) › 2016.10–2019.09
RM32H0E _52 Drivetrain _060311 EC69 MANUAL TRANSMISSION / TRANSAXLE _0303343 MANUAL TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge) A

EC69 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When the manual transaxle assembly is removed, be sure to use a new clutch release cylinder with bearing assembly and new installation bolts. Removal of the manual transaxle assembly allows the compressed clutch release cylinder with bearing assembly to return to its original position. Dust from the moving section may damage the seal of the clutch release cylinder with bearing assembly, possibly causing clutch fluid leaks.


PROCEDURE

Hide 1.INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY

a.

Coat a new O-ring with gear oil.


b.

Install the O-ring to the speedometer driven hole cover sub-assembly.


c.

Install the speedometer driven hole cover sub-assembly to the manual transaxle assembly with the bolt.

Torque:
11.3 N*m (115 kgf*cm, 8 ft.*lbf)


Hide 33823 2.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the continuously variable transaxle assembly with the 2 bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


b.

Connect the clamp to the No. 1 transmission control cable bracket.


Hide 335A0 3.INSTALL CONTROL CABLE BRACKET ASSEMBLY

a.

Install the control cable bracket assembly to the manual transmission case with the 3 bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


Hide 4.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the manual transmission case with the bolt.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


Hide 87101A 5.INSTALL NO. 1 HEATER BRACKET SUB-ASSEMBLY

a.

Install the No. 1 heater bracket sub-assembly to the manual transmission case with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 31400 6.INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

Hide 31407B 7.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 8.INSPECT CLUTCH PIPE LINE

Hide 31407B 9.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 31484 10.INSTALL CLUTCH FLEXIBLE HOSE BRACKET

a.

Install the clutch flexible hose bracket to the manual transaxle assembly with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 31483 11.INSTALL BLEEDER CLUTCH RELEASE TUBE

Hide 30300 12.INSTALL MANUAL TRANSAXLE ASSEMBLY

a.
C366694C01
0.615,0.354 1.396,0.396 true 2.396,0.906 2.729,1.396 true 0.375,0.271 0.688,0.469 0.313,0.198 10 false *1 2.792,1.302 3.104,1.5 0.313,0.198 10 false *1
*1 Knock Pin


Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.


b.

Align the input shaft with the clutch disc assembly and install the manual transaxle assembly to the engine assembly.

NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not forcibly pry on the manual transaxle assembly when installing it to the engine assembly.

·

Do not apply excessive force to the manual transaxle assembly as this will break the input shaft.

·

Make sure that the knock pins fit securely into the holes when installing the manual transaxle assembly to the engine assembly.

·

Make sure that the contact surfaces of the engine assembly and manual transaxle assembly are flat against each other before tightening the bolts.




c.
C187765E02
2.26,0.031 2.417,0.229 0.156,0.198 10 false A 1.177,0.042 1.333,0.24 0.156,0.198 10 false B

Temporarily install the bolt (A).


d.

Install the bolt (B), then fully tighten the bolt (A).

Torque:
for Flange Bolt : 37 N*m (377 kgf*cm, 27 ft.*lbf)
for Bolt with Washer : 33 N*m (337 kgf*cm, 24 ft.*lbf)


e.

Install the 5 bolts.

Torque:
for Flange Bolt : 37 N*m (377 kgf*cm, 27 ft.*lbf)
for Bolt with Washer : 33 N*m (337 kgf*cm, 24 ft.*lbf)


f.
C366703C01
0.844,1.719 1.438,1.938 0.594,0.219 10 true 1 (*a), 6 0.885,0.531 1.063,0.719 0.177,0.188 10 true 2 2.375,1.979 2.552,2.167 0.177,0.188 10 true 3 2.708,0.823 2.885,1.01 0.177,0.188 10 true 4 1.927,0.292 2.104,0.479 0.177,0.188 10 true 5
*a Temporarily Tighten


Install the engine mounting bracket LH to the manual transaxle assembly with the 5 bolts in the order shown in the illustration.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)


g.

Engage the hook to temporarily install the engine mounting insulator LH to the vehicle body.


h.
C366702C01
0.135,0.573 0.719,0.76 0.583,0.188 10 true 1 (*a), 5 2.365,1.938 2.521,2.135 0.156,0.198 10 true 2 0.823,1.51 0.979,1.708 0.156,0.198 10 true 3 2.75,1.021 2.906,1.219 0.156,0.198 10 true 4 2.417,0.063 2.573,0.26 0.156,0.198 10 true 6
*a Temporarily Tighten


Install the nut and 4 bolts in the order shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


i.

Install the transverse engine engine mounting insulator to the engine mounting bracket LH with the bolt and nut.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

HINT:

Turn the bolt while holding the nut.



Hide 11363A 13.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 12364B 15.INSTALL NO. 2 ENGINE MOVING CONTROL ROD

a.
C366699C01
2.531,0.188 3.063,0.396 0.531,0.208 10 true 1 (*a), 5 0.625,1.438 0.792,1.625 0.167,0.188 10 true 2 2.177,1.208 2.344,1.396 0.167,0.188 10 true 3 1.104,0.125 1.271,0.313 0.167,0.188 10 true 4
*a Temporarily Tighten


Install the No. 2 engine moving control rod to the manual transaxle assembly with the 4 bolts in the order shown in the illustration.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 51201 16.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 51108A 17.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 18.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

Hide 19.REMOVE ENGINE SUPPORT BRIDGE

a.

Remove SST from the vehicle body.

NOTICE:

Prevent SST from contacting the vehicle body or windshield glass.



b.

Install the neck from the windshield washer jar assembly with the clip.


Hide 20.REMOVE ENGINE HANGER

a.

Remove the 2 bolts and No. 2 engine hanger from the cylinder head.


b.

Remove the 2 bolts and No. 1 engine hanger from the cylinder head.


c.

Connect the No. 2 earth wire to the engine mounting insulator sub-assembly RH with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Install the wire harness clamp bracket to the cylinder head sub-assembly with the bolt.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


e.

Install the engine wire to the wire harness clamp bracket with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


f.

Engage the 3 clamps with the wire harness clamp bracket.


g.

Connect the wire harness to the wire harness clamp bracket.


Hide 21.INSTALL FRONT DRIVE SHAFT ASSEMBLY (for TMC Made)

Hide 22.INSTALL FRONT DRIVE SHAFT ASSEMBLY (for TMMT Made)

Hide 12321B 23.INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

Hide 31481A 24.CONNECT NO. 1 CLUTCH HOSE

a.

Connect the No. 1 clutch hose and install a new clip to the No. 1 clutch hose.

NOTICE:

Install the clip as far as it will go.



b.
C356562C01
1.26,1.531 1.458,1.708 0.198,0.177 10 true *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, install the bleeder clutch release tube to the No. 1 clutch hose.

Torque:
Specified Tightening Torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the No. 1 clutch hose.

·

Do not allow any foreign matter such as dirt or dust to enter the No. 1 clutch hose from the clip or bracket.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 25.CONNECT WIRE HARNESS

a.

Engage the 3 clamps and install the wire harness to the manual transaxle assembly.


b.

Connect the neutral position switch connector.


c.

Engage the 3 clamps and install the heated oxygen sensor wire harness to the front suspension crossmember sub-assembly.


d.

Engage the clamp and install the wire harness to the manual transaxle assembly.


e.

Install the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


f.

Connect the transmission revolution sensor connector.


g.

Connect the back-up light switch assembly connector.


Hide 17410 26.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 45025D 28.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 29.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45260 30.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 31.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 33820B 32.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C356470C02
2.052,0.719 2.406,0.26 true 1.667,0.333 2.406,0.26 true 2.302,0.5 2.458,0.698 0.156,0.198 10 true B 1.146,0.073 1.302,0.271 0.156,0.198 10 true B 1.708,1.427 1.865,1.625 0.156,0.198 10 true A 1.49,1.896 1.646,2.094 0.156,0.198 10 true A 2.448,0.104 2.635,0.302 0.188,0.198 10 true *a
*a Paint Mark


Install the transmission control cable assembly to the control cable bracket assembly with 2 new clips B.

NOTICE:

Make sure that the paint marks on the transmission control cable assembly are aligned with the slits in the control cable bracket assembly before installing the clips.



b.

Connect the transmission control cable assembly to the manual transaxle assembly with the 2 clips A.


Hide 74404A 33.INSTALL BATTERY CLAMP SUB-ASSEMBLY

a.

Install the battery clamp sub-assembly to the vehicle with the 3 bolts.

Torque:
15.4 N*m (157 kgf*cm, 11 ft.*lbf)


b.

Engage the clamp to connect the engine wire to the battery clamp sub-assembly.


c.

Connect the engine wire to the battery clamp sub-assembly with the bolt and nut.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 17701 35.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 36.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17751 37.INSTALL NO. 1 AIR CLEANER INLET

Hide 53141F 38.INSTALL RADIATOR COVER

Hide 55701J 39.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 40.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 55735C 41.INSTALL COWL BODY MOUNTING REINFORCEMENT RH

Hide 55736D 42.INSTALL COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735A 43.INSTALL WATER GUARD PLATE LH

Hide 55737B 44.INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 45.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 28800 47.INSTALL BATTERY

Hide 48.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>8NR-FTS BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 49.ADD MANUAL TRANSAXLE OIL

Hide 52.INSPECT FOR MANUAL TRANSAXLE OIL LEAK

Hide 53.INSPECT FOR EXHAUST GAS LEAK

Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>EXHAUST PIPE (for 2WD)>INSTALLATION

HINT:

Perform "Inspection After Repairs" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Hide 58166 54.INSTALL FRONT FLOOR COVER LH (w/ Cover)

Hide 58165B 55.INSTALL FRONT FLOOR COVER RH (w/ Cover)

Hide 51443C 56.INSTALL REAR ENGINE UNDER COVER RH

Hide 51444A 57.INSTALL REAR ENGINE UNDER COVER LH

Hide 51441 58.INSTALL NO. 1 ENGINE UNDER COVER

Hide 59.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT