Home › Engine / Hybrid System › 8NR-FTS (EMISSION CONTROL) › MONOLITHIC CONVERTER › 2018.05–2019.09
RM32H0E _51 Engine / Hybrid System _060038 8NR-FTS EMISSION CONTROL _0294114 MONOLITHIC CONVERTER A

8NR-FTS EMISSION CONTROL  MONOLITHIC CONVERTER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during exhaust manifold converter sub-assembly (TWC: Front Catalyst) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of air fuel ratio sensor

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A344783

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust manifold converter sub-assembly.

·

Touching high-temperature areas such as the engine and exhaust manifold converter sub-assembly could result in burns.

·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



PROCEDURE

Hide 2.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55737B 3.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 55735A 4.REMOVE WATER GUARD PLATE LH

Hide 55736D 5.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735C 6.REMOVE COWL BODY MOUNTING REINFORCEMENT RH

Hide 55701J 7.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 55225 9.REMOVE DASH PANEL HEAT INSULATOR

Hide 53141F 10.REMOVE RADIATOR COVER

Hide 17751 11.REMOVE NO. 1 AIR CLEANER INLET

Hide 17705 12.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 82121 13.REMOVE ENGINE WIRE

a.
A353510C02
0,0 0,0 false
V100135

Bolt
V100136

Nut
V100137

Connector


Disconnect the 7 connectors.


b.

Remove the bolt and nut.


c.

Disengage the 3 wire harness clamps.


d.
A353511

Remove the 2 bolts and wire harness clamp bracket from the cylinder head sub-assembly.


Hide 12261 14.REMOVE VENTILATION HOSE

a.
A353512C02
1.51,1.865 1.677,1.865 1.677,1.865 1.729,1.25 true 2.396,0.927 2.75,0.927 true 2.781,0.875 3.042,1.073 0.26,0.198 10 true *1 1.271,1.802 1.542,2 0.271,0.198 10 true *2
*1 Ventilation Hose
*2 No. 4 Ventilation Hose


Slide the 2 clips and remove the ventilation hose from the cylinder head cover sub-assembly and inlet No. 1 air duct sub-assembly.


b.

Slide the 2 clips and remove the No. 4 ventilation hose from the ventilation ejector and inlet No. 1 air duct sub-assembly.


Hide 12217 15.REMOVE VENTILATION EJECTOR

a.
A393613

Remove the bolt and separate the air tube assembly from the cylinder head cover sub-assembly.


b.

Remove the 2 bolts and ventilation ejector from the cylinder head cover sub-assembly.


c.

Remove the O-ring from the cylinder head cover sub-assembly.


Hide 17360A 16.REMOVE AIR TUBE ASSEMBLY

a.
A353514C02
1.813,1.188 2.5,1.188 true 1.281,0.427 1.458,0.427 1.458,0.427 1.677,0.813 true 2.51,1.104 2.76,1.292 0.25,0.188 10 true *1 1.063,0.344 1.281,0.531 0.219,0.188 10 true *2
*1 No. 2 Intercooler Water Hose
*2 No. 3 Intercooler Water Hose


Slide the 2 clips and disconnect the No. 2 intercooler water hose and No. 3 intercooler water hose from the turbocharger sub-assembly.


b.
A353515C02
1.521,1.365 1.917,1.365 true 0.854,1.031 1.25,1.031 true 1.938,1.292 2.198,1.49 0.26,0.198 10 true *1 0.625,0.958 0.865,1.156 0.24,0.198 10 true *2
*1 No. 2 Intercooler Water Hose
*2 No. 3 Intercooler Water Hose


Disconnect the No. 2 intercooler water hose and No. 3 intercooler water hose from the No. 1 water hose clamp bracket.


c.
A353516

Loosen the hose clamp and remove the air tube assembly from the turbocharger sub-assembly.


Hide 25819 17.REMOVE VACUUM REGULATING VALVE ASSEMBLY

a.
A353518C02
2.208,0.635 2.604,0.635 true 1.573,0.365 1.708,0.365 1.708,0.365 2,0.615 true 1.094,0.646 1.229,0.646 1.229,0.646 1.573,0.885 true 1.01,1.854 1.146,1.854 1.146,1.854 1.427,1.51 true 2.635,0.573 2.854,0.771 0.219,0.198 10 true *1 1.365,0.281 1.604,0.458 0.24,0.177 10 true *2 0.885,0.573 1.104,0.74 0.219,0.167 10 true *3 0.802,1.792 1.021,1.958 0.219,0.167 10 true *4
*1 No. 2 Vacuum Transmitting Hose
*2 No. 3 Vacuum Transmitting Hose
*3 Vacuum Regulating Valve Assembly
*4 No. 2 Vacuum Switching Valve Bracket


Disconnect the No. 2 vacuum transmitting hose and No. 3 vacuum transmitting hose from the vacuum regulating valve assembly.


b.

Remove the 3 bolts and vacuum regulating valve assembly and No. 2 vacuum switching valve bracket from the cylinder head sub-assembly.


Hide 17301C 18.REMOVE INLET NO. 1 AIR DUCT SUB-ASSEMBLY

a.
A353519

Disconnect the No. 1 vacuum transmitting hose assembly from the vacuum tank.


b.
A353520

Remove the 2 bolts and vacuum tank from the inlet No. 1 air duct sub-assembly.


c.
A353522

Disconnect the No. 1 vacuum transmitting hose assembly from the vacuum pump assembly.


d.
A427493

Remove the bolt and disconnect the inlet No. 1 air duct sub-assembly from the fuel pump protector.


e.
A396725

Disconnect the intake air control valve (air by-pass valve assembly) connector.


f.
A353521C02
2.198,0.802 2.792,0.802 true 1.677,1.354 1.948,1.979 1.948,1.979 2.135,1.979 true 2.813,0.729 3.052,0.917 0.24,0.188 10 true *1 2.167,1.906 2.427,2.083 0.26,0.177 10 true *2
*1 No. 2 Vacuum Transmitting Hose Assembly
*2 Inlet No. 1 Air Duct Sub-assembly


Disconnect the No. 2 vacuum transmitting hose assembly from the turbocharger sub-assembly.


g.

Loosen the hose clamp and remove the inlet No. 1 air duct sub-assembly from the turbocharger sub-assembly.


Hide 12611 20.REMOVE NO. 1 ENGINE COVER

a.
A353524

Remove the No. 1 engine cover from the cylinder head cover sub-assembly and cylinder head sub-assembly.


Hide 58165B 22.REMOVE FRONT FLOOR COVER RH (w/ Cover)

HINT:

Perform the same procedure as for the front floor cover LH.


Hide 17410 24.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) (for 2WD)

a.
A396115

Disconnect the heated oxygen sensor connector.


b.

Disengage the wire harness clamps.


c.
A393617

Remove the 4 bolts and 4 compression springs and disconnect the front exhaust pipe assembly (TWC: Rear Catalyst) from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and tail exhaust pipe assembly.


d.

Remove the front exhaust pipe assembly (TWC: Rear Catalyst) from the 2 exhaust pipe supports.


e.

Remove the 2 exhaust pipe gaskets from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and tail exhaust pipe assembly.


Hide 17420K 25.REMOVE NO. 2 CENTER EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) (for AWD)

a.
A393618

Remove the 4 bolts and disconnect the No. 2 center exhaust pipe assembly (TWC: Rear Catalyst) from the front exhaust pipe assembly and tail exhaust pipe assembly.


b.

Remove the No. 2 center exhaust pipe assembly (TWC: Rear Catalyst) from the 4 exhaust pipe supports.


Hide 17410 26.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for AWD)

a.
A396731

Disconnect the heated oxygen sensor connector.


b.

Disengage the wire harness clamp.


c.
A392877

Remove the 2 nuts and disconnect the front exhaust pipe assembly from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).


d.

Remove the exhaust pipe gasket from the front exhaust pipe assembly.


Hide 58151 27.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

a.
A396723

Remove the 3 nuts and front No. 1 floor heat insulator from the vehicle body.


Hide 17163 28.REMOVE NO. 1 HEAT INSULATOR BRACKET (for 2WD)

HINT:

Perform this procedure when it is necessary to replace the No. 1 heat insulator bracket.


a.
A351367

Loosen the 3 bolts of the manifold support bracket.

NOTICE:
·

Distortion may have occurred due to high temperatures.

·

Do not remove the 3 bolts. Only loosen them.




b.
A351377

Remove the bolt, nut and drive shaft heat insulator sub-assembly from the No. 1 heat insulator bracket and manifold support bracket.


c.
A446268

Remove the bolt and No. 1 heat insulator bracket from the cylinder block sub-assembly.


Hide 12321B 29.REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY (for 2WD)

a.
A351367

Loosen the 3 bolts of the manifold support bracket.

NOTICE:
·

Distortion may have occurred due to high temperatures.

·

Do not remove the 3 bolts. Only loosen them.




b.
A351377

Remove the bolt, nut and drive shaft heat insulator sub-assembly from the No. 1 heat insulator bracket and manifold support bracket.


Hide 25591 30.REMOVE MANIFOLD SUPPORT BRACKET (for 2WD)

a.
A351367

Remove the 3 bolts and manifold support bracket from the cylinder block sub-assembly and exhaust manifold converter sub-assembly (TWC: Front Catalyst).


Hide 25591 31.REMOVE MANIFOLD SUPPORT BRACKET (for AWD)

a.
A393619

Remove the 3 bolts and manifold support bracket from the cylinder block sub-assembly and exhaust manifold converter sub-assembly (TWC: Front Catalyst).


Hide 37117B 32.REMOVE PROPELLER SHAFT HEAT INSULATOR (for AWD)

a.
A393782

Remove the 3 bolts and propeller shaft heat insulator from the transfer assembly.


Hide 37109A 33.REMOVE PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY (for AWD)

a.
A393783

Remove the 2 bolts and propeller shaft heat insulator bracket sub-assembly from the transfer assembly.


Hide 25586 34.REMOVE NO. 1 MANIFOLD CONVERTER INSULATOR (for AWD)

a.

w/ Differential Pressure Sensor:

i.
A427494

Remove the nut, 3 bolts and No. 1 manifold converter insulator from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).



b.
A393781

w/o Differential Pressure Sensor:

i.

Remove the 4 bolts and No. 1 manifold converter insulator from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).



Hide 25587 35.REMOVE NO. 2 MANIFOLD CONVERTER INSULATOR (for AWD)

a.
A393780

Remove the 3 bolts and No. 2 manifold converter insulator from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).


Hide 17272 36.REMOVE NO. 2 TURBO INSULATOR

a.
A351368

Remove the 2 bolts and No. 2 turbo insulator from the cylinder head sub-assembly and heat insulator bracket.


Hide 25586 37.REMOVE NO. 1 MANIFOLD CONVERTER INSULATOR (for 2WD)

a.
A351369

Remove the 3 bolts and No. 1 manifold converter insulator from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).


Hide 25051 38.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)

a.
A393784C01
0.083,0.083 0.333,0.302 0.25,0.219 12 true *A 0.083,2.5 0.344,2.729 0.26,0.229 12 true *B
*A for 2WD
*B for AWD


Remove the 4 nuts and exhaust manifold converter sub-assembly (TWC: Front Catalyst) from the turbocharger sub-assembly.


Hide 17279 39.REMOVE OUTLET TURBINE ELBOW GASKET

a.
A351371

Remove the outlet turbine elbow gasket from the turbocharger sub-assembly.


Hide 25733A 40.REMOVE NO. 1 VACUUM PIPE (w/ Differential Pressure Sensor)

a.

for 2WD:

i.
A427495

Slide the 2 clips and remove the vacuum transmitting hose from the differential pressure sensor and No. 1 vacuum pipe.


ii.
A427496

Using a 14 mm union nut wrench, disconnect the No. 1 vacuum pipe from the exhaust manifold converter sub-assembly.


iii.

Remove the nut and No. 1 vacuum pipe.



b.

for AWD:

i.
A427497

Slide the 2 clips and remove the vacuum transmitting hose from the differential pressure sensor and No. 1 vacuum pipe.


ii.
A427498

Using a 14 mm union nut wrench, disconnect the No. 1 vacuum pipe from the exhaust manifold converter sub-assembly.


iii.

Remove the nut and No. 1 vacuum pipe.