The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B, +B2 (BATT) terminals to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
When the VC circuit has a short circuit, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.
ECM Power Source Circuit
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>ECM Power Source Circuit
VC Output Circuit
Check the fuses for circuits related to this system before performing the following inspection procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
| *1 | No. 1 Engine Room Relay Block |
| *2 | EFI NO. 3 Fuse |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (EFI NO. 3 fuse) - Body ground | Always | 11 to 14 V |
Check that a EFI NO. 3 fuse is installed in the relay block.
If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A46 accelerator pedal sensor assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the C19 camshaft position sensor (for intake camshaft) connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the W1 camshaft position sensor (for exhaust camshaft) connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the C29 crankshaft position sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the C4 throttle body with motor assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
Perform "Inspection After Repair" after replacing the throttle body with motor assembly.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
A
B
Disconnect the C3 No. 1 turbo pressure sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the C39 No. 2 turbo pressure sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the C54 fuel delivery pipe (fuel pressure sensor) connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible (for CVT) | A |
| Communication is not possible (for Manual Transaxle) | B |
| Communication is possible | C |
A
B
C
Disconnect the C44 oil pressure sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible (for 2WD) | B |
| Communication is possible (for AWD) | C |
A
B
C
Disconnect the A47 clutch pedal stroke sensor assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible (for LHD) | B |
| Communication is possible (for RHD) | C |
A
B
C
Disconnect the C58 oil pressure sender gauge assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible (w/ Differential pressure sensor) | A |
| Communication is not possible | B |
| Communication is possible | C |
A
B
C
Disconnect the C73 differential pressure sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the A46 accelerator pedal sensor assembly connector.
Disconnect the C19 camshaft position sensor (for intake camshaft) connector.
Disconnect the W1 camshaft position sensor (for exhaust camshaft) connector.
Disconnect the C29 crankshaft position sensor connector.
Disconnect the C4 throttle body with motor assembly connector.
Disconnect the C3 No. 1 turbo pressure sensor connector.
Disconnect the C39 No. 2 turbo pressure sensor connector.
Disconnect the C54 fuel delivery pipe (fuel pressure sensor) connector.
Disconnect the C44 oil pressure sensor connector. *1
Disconnect the A47 clutch pedal stroke sensor assembly connector. *2
Disconnect the C58 oil pressure sensor gauge assembly connector.
Disconnect the C73 differential pressure sensor connector.*3
Disconnect the A38 and C62 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-49 (VCPA) - Body ground and other terminals | Always | 10 kΩ or higher |
| A38-52 (VCP2) - Body ground and other terminals | Always | 10 kΩ or higher |
| C62-113 (VCV1) - Body ground and other terminals | Always | 10 kΩ or higher |
| C62-111 (VCE1) - Body ground and other terminals | Always | 10 kΩ or higher |
| C62-110 (VCNE) - Body ground and other terminals | Always | 10 kΩ or higher |
| C62-121 (VCTA) - Body ground and other terminals | Always | 10 kΩ or higher |
| C62-140 (VPTA) - Body ground and other terminals | Always | 10 kΩ or higher |
| C62-138 (VCPM) - Body ground and other terminals | Always | 10 kΩ or higher |
| C62-136 (VCPR) - Body ground and other terminals | Always | 10 kΩ or higher |
| C62-118 (VCPT)*1 - Body ground and other terminals | Always | 10 kΩ or higher |
| C62-89 (VCCL)*2 - Body ground and other terminals | Always | 10 kΩ or higher |
| C62-130 (VCPE) - Body ground and other terminals | Always | 10 kΩ or higher |
| C62-80 (VC)*3 - Body ground and other terminals | Always | 10 kΩ or higher |
| 1 (EFI NO. 3 fuse holder) - A38-2 (+B) | Always | Below 1 Ω |
| 1 (EFI NO. 3 fuse holder) - A38-3 (+B2) | Always | Below 1 Ω |
*1: for CVT
*2: for Manual Transaxle
*3: w/ Differential Pressure Sensor
| Proceed to |
|---|
| OK |
| NG |
OK
NG