Home › Engine / Hybrid System › 8NR-FTS (FUEL) › FUEL SYSTEM › 2019.09–2020.08
RM32H0E _51 Engine / Hybrid System _059909 8NR-FTS FUEL _0293894 FUEL SYSTEM G

8NR-FTS FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

Keep fuel away from rubber or leather parts.

·

If a malfunction such as pump lock occurs and the fuel pump is damaged, excessive current may be continuously applied to the fuel pump control ECU, damaging its internal parts. Make sure to replace the fuel pump control ECU at the same time when replacing the fuel pump.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Hide 2.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK

a.

Check fuel pump operation.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.

Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay
50004 372 24

v.

Check for pressure in the fuel tube sub-assembly from the fuel line. Check that sounds of fuel flowing from the fuel tank assembly can be heard. If no sounds can be heard, check the relay, fuel pump, ECM and wiring connectors.



b.

Inspect for fuel leaks.

i.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.



c.

Turn the ignition switch off.


d.

Disconnect the GTS from the DLC3.


Hide 3.CHECK FUEL PRESSURE

a.

Discharge fuel system pressure.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Measure the battery voltage.

Standard Voltage:

11 to 14 V



c.

Disconnect the cable from the negative (-) battery terminal.

Click hereGeneral>MAINTENANCE>8NR-FTS BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.

Remove the windshield wiper motor and link assembly.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL


e.

Remove the No. 1 heater air duct splash shield seal.

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>REMOVAL


f.

Remove the water guard plate LH(for TMC Made RHD).

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>REMOVAL


g.

Remove the cowl body mounting reinforcement LH.

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>REMOVAL


h.

Remove the cowl body mounting reinforcement RH.

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>REMOVAL


i.

Remove the outer cowl top panel sub-assembly (for LHD).

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>REMOVAL


j.

Remove the outer cowl top panel sub-assembly (for RHD).

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>REMOVAL


k.

l.

Remove the No. 1 air cleaner inlet.

Click hereEngine / Hybrid System>8NR-FTS (COOLING)>RADIATOR>REMOVAL


m.

Remove the air cleaner cap with air cleaner hose.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


n.
A350949

Disconnect the fuel tube sub-assembly.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL PUMP (for High Pressure)>REMOVAL


o.
A350929C03
0.281,0.635 0.375,0.635 0.375,0.635 0.406,0.917 false 1.302,3.208 1.552,3.208 false 1.375,4.094 1.563,4.094 false 3.104,2.323 3.208,2.323 3.208,2.323 3.208,2.875 false 2.771,1.135 2.875,0.875 2.875,0.875 2.969,0.875 false 2.354,0.5 2.604,0.5 false 1.75,1.271 1.865,1.271 1.865,1.271 2.01,1.021 false 1.573,2.229 1.573,2.031 false 1.313,1.104 1.313,0.813 false 1.74,4.365 1.927,4.365 false 0.104,0.552 0.417,0.708 0.313,0.156 10 false *c 1.573,1.188 1.885,1.344 0.313,0.156 10 false *b 2.917,2.24 3.229,2.396 0.313,0.156 10 false *e 1.49,2.26 1.802,2.417 0.313,0.156 10 false *d 1.188,4.01 1.5,4.167 0.313,0.156 10 false *f 1.135,3.125 1.448,3.281 0.313,0.156 10 false *a 3.021,0.781 3.333,0.938 0.313,0.156 10 false *a 2.667,0.417 2.979,0.573 0.313,0.156 10 false *a 1.25,1.135 1.563,1.292 0.313,0.156 10 false *1 1.99,4.26 2.24,4.49 0.25,0.229 10 false *g
*1 Fuel Tube Sub-assembly (Vehicle Side)
*a SST (Hose Band)
*b SST (T-joint)
*c SST (Gauge)
*d SST (Hose Joint)
*e SST (Hose)
*f SST (Fuel Tube Connector)
*g Fuel Pipe (Vehicle Side)


Install SST (EFI fuel pressure gauge) as shown in the illustration.

SST
09268-45101  (09268-41250, 09268-41260, 09268-41280, 09268-41500, 09268-41700, 95336-08070)


p.

Wipe up any spilled fuel.


q.

Connect the cable to the negative (-) battery terminal.

Click hereGeneral>MAINTENANCE>8NR-FTS BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



r.

Connect the GTS to the DLC3.


s.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



t.

Turn the GTS on.


u.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.

Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay
50004 372 24

v.

Measure the fuel pressure.

Standard Fuel Pressure:

196 to 588 kPa (2.0 to 6.0 kgf/cm2, 28 to 85 psi)


·

If the fuel pressure is less than the standard, check the fuel hoses and their connections, fuel pump, fuel filter and fuel pressure regulator assembly.

·

If the result is not as specified, replace the fuel pressure regulator assembly.



w.

Disconnect the GTS from the DLC3.


x.

Start the engine.


y.

Measure the fuel pressure at idle.

Standard Fuel Pressure:

196 to 588 kPa (2.0 to 6.0 kgf/cm2, 28 to 85 psi)


HINT:

Refer to Standard Idle Speed.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION



z.

Stop the engine.


aa.

Check that the fuel pressure remains as specified for 5 minutes.

Standard Fuel Pressure:

147 kPa (1.5 kgf/cm2, 21 psi) or more


If the result is not as specified, check the fuel pump, fuel pressure regulator assembly and/or fuel injector assemblies.


ab.

After checking the fuel pressure, disconnect the cable from the negative (-) battery terminal and carefully remove SST to prevent fuel from spraying.

Click hereGeneral>MAINTENANCE>8NR-FTS BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION




ad.

Install the air cleaner cap with air cleaner hose.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION


ae.

Install the No. 1 air cleaner inlet.

Click hereEngine / Hybrid System>8NR-FTS (COOLING)>RADIATOR>INSTALLATION


af.

ag.

Install the outer cowl top panel sub-assembly (for LHD).

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>INSTALLATION


ah.

Install the outer cowl top panel sub-assembly (for RHD).

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>INSTALLATION


ai.

Install the cowl body mounting reinforcement RH.

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>INSTALLATION


aj.

Install the cowl body mounting reinforcement LH.

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>INSTALLATION


ak.

Install the water guard plate LH(for TMC Made RHD).

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>INSTALLATION


al.

Install theNo. 1 heater air duct splash shield seal.

Click hereSuspension>FRONT SUSPENSION>FRONT SHOCK ABSORBER>INSTALLATION


am.

Install the windshield wiper motor assembly.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION



Hide 4.CHECK FUEL PRESSURE (for High Pressure)

a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start and warm up the engine.


e.

Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (High).

Powertrain > Engine > Data List
Tester Display
Fuel Pressure (High)
50003 372 265

f.

Check the high pressure side fuel pressure.

Standard Fuel Pressure:

4000 to 18000 kPa (40.8 to 183.5 kgf/cm2, 580 to 2610 psi)


If the result is not as specified, check the fuel pump, fuel pump assembly, fuel pressure sensor and wire harnesses.


g.

Stop the engine.