Home › Drivetrain › K313F (MULTIDRIVE / CVT) › TRANSMISSION CONTROL CABLE › from 2020.08
RM32H0E _52 Drivetrain _059618 K313F MULTIDRIVE / CVT _0292483 TRANSMISSION CONTROL CABLE A

K313F MULTIDRIVE / CVT  TRANSMISSION CONTROL CABLE  INSTALLATION  


PROCEDURE

Hide 33820B 1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C365142

Pass the transmission control cable assembly into the vehicle and install the transmission control cable assembly to the vehicle body with the 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.
C365141

Engage the guide to connect the transmission control cable assembly to vehicle body.


c.

Install the nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.
C329707N01
2.531,0.417 2.688,0.615 0.156,0.198 10 true N 2.823,0.938 2.979,1.135 0.156,0.198 10 true P

Turn the control shaft lever clockwise until it stops, and then from that position turn it counterclockwise by 2 notches to set it to the N position.


e.

Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


f.

Connect the transmission control cable assembly to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


g.

for TMMT Made:

i.
C366437C01
0,0 0,0 false
V113147

Install in this Direction


Connect the transmission control cable assembly to the floor shift shift lever assembly.

NOTICE:

Make sure that the transmission control cable assembly is securely locked.



ii.
C366436C02
0,0 0,0 false
V113147

Install in this Direction


Connect the end of the transmission control cable assembly to the floor shift shift lever assembly.

NOTICE:
·

Before connecting the transmission control cable assembly, check that the park/neutral position switch and shift lever are in N.

·

Install the end of the transmission control cable assembly so that the lock piece faces the driver side.

·

Install the end of the transmission control cable assembly all the way to the base of the pin.





h.

for TMC Made:

i.
C288539C01
2.24,0.906 2.552,0.708 false 1,1.875 1.313,1.677 false 0.854,1.781 1.167,1.938 0.313,0.156 10 false *1 2.594,0.604 2.906,0.76 0.313,0.156 10 false *2
*1 Nut
*2 Lock
V100135

Rotate approximately 180°
V100136

Push in


Rotate the nut of the transmission control cable assembly approximately 180° in the direction shown in the illustration, and while holding the nut in that position, push in the lock.

NOTICE:

Rotating the nut too much will damage the internal spring, and the transmission control cable assembly will not be reusable. Do not turn the nut too far.



ii.
C365195C01
0.792,2.531 0.604,2.344 false 2.813,2.542 2.625,2.354 false 2.458,2.26 2.771,2.417 0.313,0.156 10 false *1 0.458,2.229 0.771,2.385 0.313,0.156 10 false *a 0.313,2.5 0.5,2.656 0.188,0.156 10 false A 1.24,2.51 1.427,2.667 0.188,0.156 10 false A
*1 Lock
*a Protrusion
V113147

Install in this Direction


Install the transmission control cable assembly to the floor shift shift lever assembly.

NOTICE:
·

Install the transmission control cable assembly with the protrusion facing upwards.

·

After installation, make sure that the lock is projecting from A as shown in the illustration.

·

Make sure that the transmission control cable assembly is securely locked.




iii.
C365194C01
0,0 0,0 false
V113147

Install in this Direction


Confirm that the shift lever is in N, and then connect the end of the transmission control cable assembly to the floor shift shift lever assembly.

NOTICE:
·

Securely install the end of the transmission control cable assembly to the floor shift shift lever assembly.

·

Install the end of the transmission control cable assembly so that its adjustment lock section is on the driver side.





Hide 58151 3.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

a.

Install the front No. 1 floor heat insulator to the vehicle body with the 2 bolts and nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 17410 4.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 17420K 5.INSTALL NO. 2 CENTER EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 17701 9.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17705 10.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 17751 11.INSTALL NO. 1 AIR CLEANER INLET

Hide 53141F 12.INSTALL RADIATOR COVER

Hide 13.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 33504F 14.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

Hide 28800 15.INSTALL BATTERY

Hide 16.CONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 18.INSPECT FOR EXHAUST GAS LEAK

Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>EXHAUST PIPE (for AWD)>INSTALLATION

HINT:

Perform "Inspection After Repairs" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Hide 19. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART