Home › Drivetrain › EC6A (MANUAL TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE › from 2020.08
RM32H0E _52 Drivetrain _059609 EC6A MANUAL TRANSMISSION / TRANSAXLE _0292321 TRANSMISSION CONTROL CABLE N

EC6A MANUAL TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  ADJUSTMENT  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 28800 3.REMOVE BATTERY

Hide 4.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 53141F 5.REMOVE RADIATOR COVER

Hide 17751 6.REMOVE NO. 1 AIR CLEANER INLET

Hide 17705 7.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 17701 8.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 11.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
·
C332327

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to neutral, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 33820B 12.ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY

HINT:
·

After the floor shift shift lever assembly or the transmission control cable assembly is replaced, be sure to adjust the transmission control cable assembly.

·

If the shift lever does not move (or the shift lever is difficult to move) to the 1st or 2nd position, or if it is possible to move the shift lever to the reverse position without pulling up the slider shaft, the length of the transmission control cable assembly must be adjusted.



a.
C365818

Remove the clip to disconnect the transmission control select cable from the floor shift shift lever assembly.


b.
C272829C03
0.052,0.073 3.365,2.135 3.313,2.063 0.073,2.583 3.365,4.469 3.292,1.885 1.094,0.917 1.25,0.635 1.25,0.635 1.417,0.635 false 1.448,1.844 1.448,1.583 false 0.521,1.865 0.521,1.604 false 0.521,4.135 0.521,3.875 false 1.469,4.115 1.469,3.854 false 2.698,0.438 3.01,0.594 0.313,0.156 10 false *a 0.458,1.875 0.771,2.031 0.313,0.156 10 false *2 1.385,1.875 1.698,2.031 0.313,0.156 10 false *3 1.469,0.552 1.781,0.708 0.313,0.156 10 false *1 0.635,0.583 0.948,0.74 0.313,0.156 10 false *b 2.615,2.74 2.927,2.896 0.313,0.156 10 false *c 1.438,4.177 1.75,4.333 0.313,0.156 10 false *3 0.458,4.177 0.771,4.333 0.313,0.156 10 false *2
*1 Lock Piece
*2 Stopper
*3 Adjuster Case
*a Twist the stopper
*b Pull out
*c Return the stopper


Release the lock of the transmission control select cable length adjustment structure.

i.

Twist the stopper.


ii.

Pull the lock piece outward from the adjuster case to release the lock.


iii.

Return the stopper.



c.
C365818

Connect the transmission control select cable to the floor shift lever assembly and install the clip.

NOTICE:
·

Make sure that the lock piece of the transmission control select cable length adjustment structure is facing upward when the transmission control select cable is connected.

·

Make sure that the transmission control select cable is securely installed.




d.
C356478C01
2.021,2.146 1.594,1.448 true 2,0.302 1.813,0.688 true 2.083,2.208 2.396,2.365 0.313,0.156 10 false *1 2.083,0.198 2.396,0.354 0.313,0.156 10 true *2 0.146,2.635 0.458,2.792 0.313,0.156 10 false *a
*1 Outer Lever
*2 Reverse Restrict Pin Assembly
*a Secured


Hook the outer lever of the manual transaxle assembly to the reverse restrict pin assembly to secure it.


e.
C365823C01
0.74,2.5 0.5,2.292 true 0.885,2.229 0.646,2.021 true 0.438,1.906 0.604,2.073 0.167,0.167 10 true *a 0.313,2.188 0.479,2.354 0.167,0.167 10 true *b
*a Slider Shaft
*b Cam Wall


Push the slider shaft against the cam wall.

NOTICE:
·

Do not pull up the slider shaft.

·

When adjusting the transmission control select cable, make sure that the shift lever is not in 1st or 2nd.




f.

Lock the transmission control select cable length adjustment structure.

i.

Twist the stopper.

C365824C02
1.438,0.552 1.667,0.333 false 0.833,1.781 0.583,1.417 0.583,1.417 0.833,1.115 false 2,2.052 2.25,1.417 2.25,1.417 2,1.104 false 1.74,0.229 2.052,0.385 0.313,0.156 10 false *1 0.385,1.323 0.698,1.479 0.313,0.156 10 false *2 2.313,1.313 2.625,1.469 0.313,0.156 10 false *3 2.688,0.177 3,0.333 0.313,0.156 10 false *a 0.99,0.25 1.302,0.406 0.313,0.156 10 false *b 2.688,1.542 3,1.698 0.313,0.156 10 false *c
*1 Lock Piece *2 Stopper
*3 Adjuster Case - -
*a Twist the stopper *b Push
*c Return the stopper - -



ii.

Push the lock piece into the adjuster case with slider held against the cam wall.

NOTICE:
·

Securely press in the lock piece until the lock engages.

·

When adjusting the transmission control select cable, make sure that the shift lever is not in 1st or 2nd.




iii.

Return the stopper to prevent the lock from being released.

NOTICE:
·

Push the lock piece as far as it will go.

·

Confirm whether the transmission control select cable length adjustment structure is locked securely.





g.
C356480C02
1.51,0.865 1.76,0.219 true 1.271,2.073 1.521,1.427 true 1.135,2.104 1.365,2.313 0.229,0.208 10 true *1 1.823,0.125 2,0.323 0.177,0.198 10 true *2 1.01,3.208 1.25,3.427 0.24,0.219 10 true *a
*1 Outer Lever
*2 Reverse Restrict Pin Assembly
*a Released


Move the shift lever to the reverse position, so that the outer lever can be released.


Hide 17701 15.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17705 16.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 17751 17.INSTALL NO. 1 AIR CLEANER INLET

Hide 53141F 18.INSTALL RADIATOR COVER

Hide 19.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 28800 20.INSTALL BATTERY

Hide 21. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART