Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.10–2016.05
RM19V0EQ _54 Brake _014591 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0076218 ANTI-LOCK BRAKE SYSTEM S

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  DIAGNOSTIC TROUBLE CODE CHART  


Anti-lock Brake System
DTC No. Detection Item DTC Detection Condition Trouble Area Link
C1237 Speed Sensor Rotor Faulty Any of the following is detected:
1.

Discrepancy among four wheel speed sensor output.

2.

Abnormal pulse signals from 3 or more sensors.

3.

Continuous ABS control is performed for 60 seconds or more.


·

Tire and wheel size

·

Tire deformation

·

Speed sensor rotor

·

Speed sensor

·

Speed sensor circuit

·

Skid control ECU (Brake actuator assembly)


Click here
C1241 Low Power Supply Voltage Malfunction Any of the following is detected:
1.

The vehicle speed is 6 km/h (4 mph) or more and the +BS terminal voltage (soft low voltage) is less than 9.6 V for 1 second or more.

2.

The vehicle speed is 6 km/h (4 mph) or more and the +BS terminal voltage (hard low voltage) is less than 6.9 V for 1 second or more.

3.

The vehicle speed is 15 km/h (9 mph) or more, the +BS terminal voltage is 9.6 V or more, the skid control ECU turns on more than one valve at the same time within a short period of time and the valve relay supply voltage drop exceeds the threshold. (The skid control ECU monitors the resistance of the power source line at the +BS terminal. A malfunction is detected when an abnormality occurs in the +BS terminal wire harness or its connection and the skid control ECU determines that the wiring resistance at the +BS terminal exceeds the standard resistance.)

4.

The +BS terminal voltage is less than 6.7 V and the skid control ECU judges that power supply voltage is abnormal for 0.06 seconds or more.


·

ABS NO. 2 fuse

·

Battery

·

Charging system

·

Power source circuit

·

Ground circuit

·

Internal power supply circuit of the skid control ECU


Click here
C1271 Low Output Signal of Front Speed Sensor RH (Test Mode DTC) Detected only during Test Mode.
·

Front speed sensor RH/LH

·

Sensor installation

·

Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH)


Click here
C1272 Low Output Signal of Front Speed Sensor LH (Test Mode DTC) Detected only during Test Mode.
·

Front speed sensor RH/LH

·

Sensor installation

·

Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH)


Click here
C1273 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) Detected only during Test Mode.
·

Rear speed sensor RH/LH

·

Sensor installation

·

Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH)


Click here
C1274 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) Detected only during Test Mode.
·

Rear speed sensor RH/LH

·

Sensor installation

·

Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH)


Click here
C1275 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) Detected only during Test Mode. Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH) Click here
C1276 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) Detected only during Test Mode. Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH) Click here
C1277 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) Detected only during Test Mode. Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH) Click here
C1278 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) Detected only during Test Mode. Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH) Click here
C1300 Skid Control ECU Malfunction Internal failure of the skid control ECU control unit. Skid control ECU (Brake actuator assembly) Click here
C1330 Open in Front Speed Sensor RH An open or short in the speed sensor signal circuit.
·

Front speed sensor RH/LH

·

Speed sensor circuit

·

Sensor installation


Click here
C1331 Open in Front Speed Sensor LH An open or short in the speed sensor signal circuit.
·

Front speed sensor RH/LH

·

Speed sensor circuit

·

Sensor installation


Click here
C1332 Open in Rear Speed Sensor RH An open or short in the speed sensor signal circuit.
·

Rear speed sensor RH/LH

·

Speed sensor circuit

·

Sensor installation


Click here
C1333 Open in Rear Speed Sensor LH An open or short in the speed sensor signal circuit.
·

Rear speed sensor RH/LH

·

Speed sensor circuit

·

Sensor installation


Click here
C1417 High Power Supply Voltage Malfunction +BS terminal voltage is more than 16.5 V for 1 second or more.
·

ABS NO. 2 fuse

·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of the skid control ECU


Click here
C1425 Open in Stop Light Switch Circuit An open in the stop light switch input line continues for 3 seconds or more.
·

STOP fuse

·

Stop light switch assembly

·

Stop light switch circuit

·

Skid control ECU (Brake actuator assembly)


Click here
C1428 Motor Circuit Malfunction A malfunction occurs in the pump motor circuit. Pump motor circuit Click here
C1464 Front Speed Sensor RH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input for 0.4 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), the wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a front wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

·

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


·

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)


·

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Front speed sensor RH/LH

·

Speed sensor circuit

·

Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH)

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


Click here
C1465 Front Speed Sensor LH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input for 0.4 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), the wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a front wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

·

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


·

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)


·

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Front speed sensor RH/LH

·

Speed sensor circuit

·

Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH)

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


Click here
C1466 Rear Speed Sensor RH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input for 0.4 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), the wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a rear wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

·

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)

·

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)

·

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Rear speed sensor RH/LH

·

Speed sensor circuit

·

Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH)

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


Click here
C1467 Rear Speed Sensor LH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input for 0.4 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), the wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a rear wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

·

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)

·

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)

·

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Rear speed sensor RH/LH

·

Speed sensor circuit

·

Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH)

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


Click here
C1468 SFR Solenoid Circuit Solenoid valve signal does not match the check result.
·

Solenoid circuit

·

Solenoid valve (Brake actuator assembly)


Click here
C1469 SFL Solenoid Circuit Solenoid valve signal does not match the check result.
·

Solenoid circuit

·

Solenoid valve (Brake actuator assembly)


Click here
C146A SRR Solenoid Circuit Solenoid valve signal does not match the check result.
·

Solenoid circuit

·

Solenoid valve (Brake actuator assembly)


Click here
C146B SRL Solenoid Circuit Solenoid valve signal does not match the check result.
·

Solenoid circuit

·

Solenoid valve (Brake actuator assembly)


Click here
C146C Open in ABS Motor Relay Circuit Any of the following is detected:
1.

When the ABS motor relay is actuated, voltage is not supplied to the pump motor.

2.

When the ABS motor relay is not actuated, voltage in the pump motor is high.

3.

The skid control ECU judges that pump motor operation is abnormal.


·

ABS NO. 1 fuse (Fusible link block assembly)

·

ABS motor relay circuit

·

ABS motor relay (Brake actuator assembly)


Click here
C146E Open in ABS Solenoid Relay Circuit Either of the following is detected:
1.

A solenoid relay drive circuit in the skid control ECU is malfunctioning.

2.

The solenoid relay cannot be switched between on and off.


·

ABS NO. 2 fuse (Fusible link block assembly)

·

ABS solenoid relay circuit

·

ABS solenoid relay (Brake actuator assembly)


Click here
U0073 Control Module Communication Bus OFF The +BS terminal voltage is between 9.6 and 16.5 V and bus off is judged for 0.1 seconds or more. CAN communication system Click here