Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P2A00  A/F Sensor Circuit Slow Response (Bank 1 Sensor 1)  P2A03  A/F Sensor Circuit Slow Response (Bank 2 Sensor 1)  


DESCRIPTION

Refer to DTC P2195 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P2195).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) Calculated value of the air fuel ratio sensor response rate deterioration level is less than the threshold (2 trip detection logic).
·

Air fuel ratio sensor (bank 1 sensor 1)

·

Intake system

·

Fuel injector assembly

·

Fuel pump

·

Fuel line

·

ECM


Comes on (Euro-OBD) / - (except Euro-OBD) DTC stored (Euro-OBD) / - (except Euro-OBD)
P2A03 A/F Sensor Circuit Slow Response (Bank 2 Sensor 1) Calculated value of the air fuel ratio sensor response rate deterioration level is less than the threshold (2 trip detection logic).
·

Air fuel ratio sensor (bank 2 sensor 1)

·

Intake system

·

Fuel injector assembly

·

Fuel pump

·

Fuel line

·

ECM


Comes on (Euro-OBD) / - (except Euro-OBD) DTC stored (Euro-OBD) / - (except Euro-OBD)

MONITOR DESCRIPTION

After the engine is warmed up, the ECM performs air fuel ratio feedback control to maintain the air fuel ratio at the stoichiometric level. In addition, active air fuel ratio control is performed for approximately 10 seconds after the preconditions are met in order to measure the air fuel ratio sensor response rate. During active air fuel ratio control, the ECM forcibly increases and decreases the injection volume by a certain amount based on the stoichiometric air fuel ratio learned during normal air fuel ratio control, and measures the air fuel ratio sensor response rate. The ECM receives a signal from the air fuel ratio sensor while performing active air fuel ratio control and uses it to calculate the air fuel ratio sensor response rate deterioration level.

If the value for the air fuel ratio sensor response rate deterioration level is less than the threshold, the ECM interprets this as a malfunction and stores the DTC.

A115363E65
4.281,1.458 4.125,1.156 false 5.229,1.615 5.448,1.052 false 0.021,0.042 2.75,0.229 2.729,0.188 10 false Air Fuel Ratio Sensor Output: 0.021,0.74 1.813,0.927 1.792,0.188 10 false Active Air Fuel Ratio Control 0.021,1.781 1.896,1.969 1.875,0.188 10 false Air Fuel Ratio Sensor Output 3.656,1.042 4.156,1.229 0.5,0.188 10 false Normal 5.469,0.958 6.229,1.146 0.76,0.188 10 false Malfunction 4.521,0.208 5.333,0.396 0.813,0.188 10 false 10 Seconds 0.021,2.698 1.427,2.885 1.406,0.188 10 false Fuel Injection Volume 2.896,2.458 3.542,2.646 0.646,0.188 10 false Increase 2.896,2.917 3.542,3.104 0.646,0.188 10 false Decrease 1.844,0.552 2.24,0.698 0.396,0.146 10 false ON 1.844,0.844 2.219,1.031 0.375,0.188 10 false OFF

MONITOR STRATEGY

Required Sensors/Components Air fuel ratio sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Active air fuel ratio control Performing
Active air fuel ratio control is performed when the following conditions met -
Engine coolant temperature 75°C (167°F) or higher
Idling Off
Engine speed Less than 4000 rpm
Air fuel ratio sensor status Activated
Engine load 10% or higher, and less than 70%
Shift position 2nd or higher
Catalyst monitor Not yet
Mass air flow 14 gm/sec. or more, and less than 42 gm/sec.

CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation driving pattern will activate the air fuel ratio sensor response monitor.


A269251E08
1.333,0.854 1.635,0.458 1.635,0.458 1.698,0.458 false 0.177,2.448 1.667,2.688 1.49,0.24 10 false Ignition Switch off 0.927,2.219 1.51,2.469 0.583,0.25 10 false Idling 1.771,2.677 2.583,2.854 0.813,0.177 10 false Warming up 2.969,2.719 4.24,2.865 1.271,0.146 10 false 10 minutes or more 5.458,2.74 6.729,2.885 1.271,0.146 10 false 10 minutes or more 0.333,0.135 1.344,0.354 1.01,0.219 10 false Vehicle Speed 0.75,1.146 1.448,1.406 0.698,0.26 10 false 60 km/h 2.031,2.135 2.229,2.313 0.198,0.177 10 false [A] 3.427,1.26 3.667,1.438 0.24,0.177 10 false [B] 4.375,3.104 4.583,3.302 0.208,0.198 10 false [C] 5.969,0.885 6.25,1.083 0.281,0.198 10 false [D] 6.75,3.104 6.958,3.302 0.208,0.198 10 false [E] 1.74,0.375 3.458,0.552 1.719,0.177 10 false Between 75 and 100 km/h

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the tester on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the tester on.

7.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

8.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more in a city area [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine / DTC [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P2A00 or P2A03.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A and no pending DTC is output, perform the following procedure.



14.

Drive the vehicle at a speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


15.

Enter the following menus: Powertrain / Engine / DTC [E].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

18.

Input the DTC: P2A00 or P2A03.

19.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

DTC P2A00 indicates malfunctions related to the bank 1 air fuel ratio sensor.

·

DTC P2A03 indicates malfunctions related to the bank 2 air fuel ratio sensor.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

DTC P2A00 or P2A03 may be stored when the air fuel ratio is stuck at a rich or lean value.

·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00 AND/OR P2A03)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / DTC.

Powertrain > Engine > Trouble Codes
50001 234

e.

Read the DTCs.

Result:
Result Proceed to
DTC P2A00 and/or P2A03 are output A
DTC P2A00 and/or P2A03 and other DTCs are output B


HINT:

If any DTCs other than P2A00 and/or P2A03 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
AFS Voltage B1S1
AFS Voltage B2S1
O2S B1S2
O2S B2S2
50004 234 2 35,37,44,48

f.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.


g.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


Tester Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1
AFS Voltage B2S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
O2S B2S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V


Result:
Status of AFS Voltage B1S1 or AFS Voltage B2S1 Status O2S B1S2 or O2S B2S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Proceed to
Lean/Rich Lean/Rich Normal A
Lean Lean Actual air fuel ratio lean B
Rich Rich Actual air fuel ratio rich B
Lean Lean/Rich Air fuel ratio sensor malfunction C
Rich Lean/Rich Air fuel ratio sensor malfunction C



Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltages (AFS Voltage B1S1 and AFS Voltage B2S1) are consistently higher than 3.4 V, and the heated oxygen sensor output voltages (O2S B1S2 and O2S B2S2) are consistently below 0.4 V.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, the AFS Voltage B1S1 and AFS Voltage B2S1 are consistently below 3.1 V, and the O2S B1S2 and O2S B2S2 are consistently higher than 0.55 V.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output voltage of the heated oxygen sensor alternates correctly.

HINT:

Refer to "Data List / Active Test" [AFS Voltage B1S1 and AFS Voltage B2S1, O2S B1S2 and O2S B2S2].

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST




A

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 OR P2A03)

B

4.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

C

9.REPLACE AIR FUEL RATIO SENSOR
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 OR P2A03)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the tester on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 234 20

j.

Input the DTC: P2A00 or P2A03.


k.

Check the DTC judgment result.


Result:
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P2A00 or P2A03 is output) B



A

B

9.REPLACE AIR FUEL RATIO SENSOR
4.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

OK

5.CHECK INTAKE SYSTEM

NG

5.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>2GR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks in the intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

6.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE INTAKE SYSTEM

6.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

7.INSPECT FUEL INJECTOR ASSEMBLY

NG

8.INSPECT FUEL PUMP
7.INSPECT FUEL INJECTOR ASSEMBLY
a.

Inspect the fuel injector assembly.

Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

9.REPLACE AIR FUEL RATIO SENSOR

NG

REPLACE FUEL INJECTOR ASSEMBLY

8.INSPECT FUEL PUMP
a.

Inspect the fuel pump.

Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL PUMP>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE FUEL LINE

NG

9.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (P2A00 OR P2A03)
10.CHECK WHETHER DTC OUTPUT RECURS (P2A00 OR P2A03)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the tester on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 234 20

j.

Input the DTC: P2A00 or P2A03.


k.

Check the DTC judgment result.


Result:
Result Proceed to
ABNORMAL (DTC P2A00 or P2A03 is output) A
NORMAL (DTC is not output) B



A

11.REPLACE ECM

B

END

11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 OR P2A03)
12.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 OR P2A03)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the tester on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 234 20

j.

Input the DTC: P2A00 or P2A03.


k.

Check that the DTC judgment result is NORMAL.


Result:
Proceed to
NEXT



NEXT

END