Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › ENGINE
RM2030EQ _51 Engine / Hybrid System _014635 2GR-FE ENGINE MECHANICAL _0074410 ENGINE G

2GR-FE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 17801 4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly.


b.

Visually check that the air cleaner filter element sub-assembly is not excessively damaged or oily. If necessary, replace the air cleaner filter element sub-assembly.

HINT:
·

If there is any dirt or a blockage in the air cleaner filter element sub-assembly, clean it with compressed air.

·

If any dirt or a blockage remains even after cleaning the air cleaner filter element sub-assembly with compressed air, replace it.




c.

Install the air cleaner filter element sub-assembly.


Hide 16620 6.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY


b.

Check that nothing is caught in the tensioner by turning it clockwise and counterclockwise. If a malfunction exists, replace the V-ribbed belt tensioner assembly.



Hide 8.INSPECT VALVE LASH ADJUSTER NOISE

a.

Rev up the engine several times. Check that the engine does not emit unusual noises.

If unusual noises occur, warm up the engine and idle it for over 30 minutes. Then perform the preceding inspection.

HINT:

If any defects or problems are found during the preceding inspection, perform lash adjuster inspection.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION



Hide 9.INSPECT IGNITION TIMING

a.

Warm up and stop the engine.

HINT:

A warmed up engine should have an engine coolant temperature of over 80°C (176°F), an engine oil temperature of 60°C (140°F), and the engine speed should be stabilized.



b.

When using the intelligent tester:

Check the ignition timing.

i.

Connect the intelligent tester to the DLC3.


ii.

Start the engine and run it at idle.


iii.

Turn the intelligent tester main switch on.


iv.

Enter the following menus: Powertrain / Engine / Data List / IGN Advance.

Powertrain > Engine > Data List
Tester Display
IGN Advance
50003 234 29
Standard ignition timing:

9.5 to 24.5° BTDC at idle


NOTICE:
·

Check the ignition timing with the cooling fans off.

·

Turn off all electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.



HINT:

Refer to the intelligent tester operator's manual for further details.



v.

Check that the ignition timing advances immediately when the engine speed is increased.


vi.

Enter the following menus: Powertrain / Engine / Active Test / Connect the TC and TE1.

Powertrain > Engine > Active Test
Active Test Display
Connect the TC and TE1
Data List Display
IGN Advance
50004 234 13 29

vii.

Monitor IGN Advance.


viii.

Perform the Active Test.

Standard ignition timing:

8 to 12° BTDC at idle


NOTICE:

When checking the ignition timing, the transaxle should be in neutral or park.


HINT:

Refer to the intelligent tester operator's manual for further details.




c.

When not using the intelligent tester:

i.
A122830
1.094,0.604 1.552,1.063 false 1.76,1.656 1.375,2.042 false 0.927,1.063 1.042,1.219 0.115,0.156 10 1 0.927,1.469 1.042,1.625 0.115,0.156 10 9 1.104,1.469 1.281,1.625 0.177,0.156 10 10 1.302,1.469 1.479,1.625 0.177,0.156 10 11 1.51,1.469 1.688,1.625 0.177,0.156 10 12 1.719,1.469 1.896,1.625 0.177,0.156 10 13 1.927,1.469 2.104,1.625 0.177,0.156 10 14 2.125,1.469 2.302,1.625 0.177,0.156 10 15 2.333,1.469 2.51,1.625 0.177,0.156 10 16 1.135,1.063 1.25,1.219 0.115,0.156 10 2 1.344,1.063 1.458,1.219 0.115,0.156 10 3 1.552,1.063 1.667,1.219 0.115,0.156 10 4 1.75,1.063 1.865,1.219 0.115,0.156 10 5 1.958,1.063 2.073,1.219 0.115,0.156 10 6 2.156,1.063 2.271,1.219 0.115,0.156 10 7 2.365,1.063 2.479,1.219 0.115,0.156 10 8 0.792,0.5 1.042,0.656 0.25,0.156 10 CG 1.594,0.156 1.76,0.333 0.167,0.177 10 *1 1.115,1.958 1.365,2.104 0.25,0.146 10 TC
*1 DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:
·

Confirm the terminals before connecting them. Connecting the wrong terminals may result in damage to electrical components.

·

Check the ignition timing with the cooling fans off.

·

Turn off all the electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.




ii.

Remove the V-bank cover sub-assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL


iii.

Connect the timing light tester probe to the ignition coil wire for No. 1 cylinder.

NOTICE:

Use a timing light that detects primary signals.



iv.

Check the ignition timing at idle.

Standard ignition timing:

8 to 12° BTDC at idle


NOTICE:

When checking the ignition timing, the transaxle should be in neutral or park.


HINT:

Run the engine at 1000 to 1300 rpm for 5 seconds, and then check that the engine rpm returns to idle speed.



v.

Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.


vi.

Check the ignition timing at idle.

Standard ignition timing:

9.5 to 24.5° BTDC at idle



vii.

Confirm that the ignition timing advances immediately when the engine rpm is increased.


viii.

Remove the timing light from the engine.


ix.

Install the V-bank cover sub-assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION



Hide 10.INSPECT ENGINE IDLE SPEED

a.

Warm up and stop the engine.

HINT:

A warmed up engine should have an engine coolant temperature of over 80°C (176°F), an engine oil temperature of 60°C (140°F), and the engine speed should be stabilized.



b.

When using the intelligent tester:

Check the idle speed.

i.

Connect the intelligent tester to the DLC3.


ii.

Start the engine and run it at idle.


iii.

Turn the intelligent tester main switch on.


iv.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 234 9

v.

Read the value displayed on the tester.

Standard idle speed:

600 to 700 rpm


NOTICE:
·

Check the idle speed with the cooling fans off.

·

Turn off all the electrical systems and the A/C.

·

When checking the idle speed, the transaxle should be in neutral or park.



HINT:
·

Refer to the intelligent tester operator's manual for further details.

·

If the speed is not as specified, check the air intake system.





c.

When not using the intelligent tester:

i.
A122830
1.094,0.604 1.552,1.063 false 1.76,1.656 1.375,2.042 false 0.927,1.063 1.042,1.219 0.115,0.156 10 1 0.927,1.469 1.042,1.625 0.115,0.156 10 9 1.104,1.469 1.281,1.625 0.177,0.156 10 10 1.302,1.469 1.479,1.625 0.177,0.156 10 11 1.51,1.469 1.688,1.625 0.177,0.156 10 12 1.719,1.469 1.896,1.625 0.177,0.156 10 13 1.927,1.469 2.104,1.625 0.177,0.156 10 14 2.125,1.469 2.302,1.625 0.177,0.156 10 15 2.333,1.469 2.51,1.625 0.177,0.156 10 16 1.135,1.063 1.25,1.219 0.115,0.156 10 2 1.344,1.063 1.458,1.219 0.115,0.156 10 3 1.552,1.063 1.667,1.219 0.115,0.156 10 4 1.75,1.063 1.865,1.219 0.115,0.156 10 5 1.958,1.063 2.073,1.219 0.115,0.156 10 6 2.156,1.063 2.271,1.219 0.115,0.156 10 7 2.365,1.063 2.479,1.219 0.115,0.156 10 8 0.792,0.5 1.042,0.656 0.25,0.156 10 CG 1.594,0.156 1.76,0.333 0.167,0.177 10 *1 1.115,1.958 1.365,2.104 0.25,0.146 10 TC
*1 DLC3


Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.

SST
09843-18030  


ii.

Check the idle speed.

Standard idle speed:

600 to 700 rpm


NOTICE:
·

Check the idle speed with the cooling fans off.

·

Turn off all the electrical systems and the A/C.

·

When checking the idle speed, the transaxle should be in neutral or park.



HINT:

If the speed is not as specified, check the air intake system.




Hide 11.INSPECT COMPRESSION

a.

Warm up and stop the engine.

HINT:

A warmed up engine should have an engine coolant temperature of over 80°C (176°F), an engine oil temperature of 60°C (140°F), and the engine speed should be stabilized.




c.
A129621

Check the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

While cranking the engine, measure the compression pressure.

Standard compression pressure:

1300 kPa (13.3 kgf/cm2, 189 psi)


Minimum pressure:

1000 kPa (10.2 kgf/cm2, 145 psi)


NOTICE:
·

Always use a fully charged battery to obtain an engine speed of 250 rpm or more.

·

Check the compression pressure of the other cylinders in the same way.

·

This measurement must be done as quickly as possible.




iii.

If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect again.

HINT:
·

If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.

·

If the pressure stays low, a valve may be stuck or seated improperly, or there may be leakage in the gasket.






Hide 12.INSPECT CO/HC

HINT:

This check determines whether or not the idle CO/HC complies with regulations.


a.

Start the engine.


b.

Keep the engine speed at 2500 rpm for approximately 180 seconds.


c.

Insert the CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idle.


d.

Immediately check CO/HC concentration during idle and when running at 2500 rpm.

HINT:

When performing the 2 mode (with the engine idling/running at 2500 rpm) test, follow the measurement order determined by applicable local regulations.

If the CO/HC concentration does not comply with the regulations, perform troubleshooting in the order given below.



ii.

See the table below for possible causes, then inspect and correct the applicable causes if necessary.

CO HC Problem Cause
Normal High Rough idle
1.

Faulty ignition:

·

Incorrect valve timing

·

Fouled, shorted or improperly gapped plugs


2.

Incorrect valve clearance (valve lash adjuster)

3.

Leaks in intake or exhaust valves

4.

Leaks in cylinders


Low High Rough idle
(Fluctuating HC reading)
1.

Vacuum leaks:

·

PCV hoses

·

Intake manifold

·

Throttle body assembly

·

Brake booster line


2.

Lean mixture causing misfire


High High Rough idle
(Black smoke from exhaust)
1.

Restricted air cleaner filter element sub-assembly

2.

Plugged PCV valve

3.

Faulty SFI system:

·

Faulty fuel pressure regulator

·

Defective engine coolant temperature sensor

·

Defective mass air flow meter

·

Faulty ECM

·

Faulty injector assemblies

·

Faulty throttle position sensor (built in throttle body assembly)