G92X2
1.INSTALL NO. 2 HYBRID BATTERY PACK WIRE
Wear insulated gloves.
Connect the connector and 5 clamps, and install the No. 2 hybrid battery pack wire.
G92Z0
2.INSTALL HYBRID BATTERY JUNCTION BLOCK ASSEMBLY
G920Q
3.INSTALL NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY
Wear insulated gloves.
Install the No. 1 hybrid battery shield sub-assembly with the bolt and 3 nuts.
89892A
4.INSTALL BATTERY SMART UNIT
G92Q2
5.INSTALL NO. 2 HYBRID VEHICLE BATTERY SHIELD PANEL
Wear insulated gloves.
Install the No. 2 hybrid vehicle battery shield panel with the 2 bolts and nut.
Connect the 3 wire harness clamps.
Connect the connector.
| *1 | Battery Cover Lock Striker |
| *2 | Button |
| *a | Push |
Install the battery cover lock striker, then push the button to lock it.
G9510
6.INSTALL HV BATTERY
Wear insulated gloves.
| *1 | Cardboard |
Place a piece of cardboard in the luggage compartment.
Using a suitable adaptor such as a rope, install the HV battery to the vehicle in the same direction it was facing during removal.
Use cardboard or other similar material to protect the HV battery and vehicle body from damage.
| *a | Push |
| *b | Turn 180° |
Push the cardboard and HV battery together to the middle of the luggage compartment.
Turn the cardboard and HV battery 180° together.
Install the battery cooling blower assembly with the 3 nuts.
Be sure not to touch the fan part of the battery cooling blower assembly.
Do not lift the battery cooling blower assembly using the wire harness.
Connect the connector.
Engage the 2 claws to install the No. 2 hybrid battery intake duct.
Ensure that the duct is installed securely.
Install the clip.
Install the 2 clips.
| *a | Push |
Push the HV battery together with the cardboard toward the front of the vehicle.
Align the holes for the HV battery holding bolts.
| *a | Hold up |
| *b | Pull out |
Use a tire lever to hold up the HV battery and pull out the cardboard.
Remove the luggage compartment floor mat.
| *1 | Ground Bolt |
Install the HV battery with the 6 bolts.
Install the ground bolts to the locations shown in the illustration.
7.CONNECT LOW VOLTAGE CONNECTOR
Connect the 3 connectors.
82164C
8.CONNECT NO. 4 FLOOR WIRE
G92Q6
9.INSTALL NO. 4 HYBRID BATTERY SHIELD PANEL
G92D1
10.INSTALL NO. 1 HYBRID BATTERY INTAKE DUCT
11.INSTALL AUXILIARY BATTERY
64271G
12.INSTALL ROOM PARTITION BOARD RH
64272B
13.INSTALL ROOM PARTITION BOARD LH
64330
14.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade)
64330
15.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)
73373
16.INSTALL REAR SEAT SHOULDER BELT COVER
62471A
17.INSTALL ROOF SIDE INNER GARNISH RH
62472A
18.INSTALL ROOF SIDE INNER GARNISH LH
Use the same procedure as for the RH side.
62331A
19.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
62332A
20.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
73370C
21.CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH
73360C
22.CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH
23.INSTALL REAR SIDE SEATBACK ASSEMBLY LH
24.INSTALL REAR SIDE SEATBACK ASSEMBLY RH
25.INSTALL REAR SEATBACK ASSEMBLY LH
64277C
26.INSTALL NO. 2 ROOM PARTITION COVER
27.INSTALL REAR SEATBACK ASSEMBLY RH
72693
28.INSTALL REAR SEAT CUSHION LOCK HOOK
29.INSTALL REAR SEAT CUSHION ASSEMBLY
64722
30.INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER LH
64721
31.INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER RH
64725D
32.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
58387
33.INSTALL REAR FLOOR FINISH PLATE
G3834
34.INSTALL SERVICE PLUG GRIP