Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB BOLT
RM2040EQ _52 Drivetrain _014703 AXLE AND DIFFERENTIAL _0074960 REAR AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  REAR AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

NOTICE:

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55702A 3.REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 4.DISABLE BRAKE CONTROL

Hide 5.REMOVE REAR WHEEL

Hide 6.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

a.
C083014

Remove the bolt and separate the rear flexible hose from the rear shock absorber assembly.


b.

Remove the 2 bolts, and separate the rear disc brake caliper assembly.

NOTICE:

Use wire or an equivalent tool to keep the rear disc brake caliper assembly from hanging down by the rear flexible hose.



Hide 42491 7.REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 42431 8.REMOVE REAR DISC

Hide 42312E 9.REMOVE REAR AXLE HUB BOLT

a.
C240540C06
2.198,1.146 2.531,1.146 false 1.333,1.417 1.333,1.906 false 1.604,0.979 1.604,0.583 1.604,0.583 1.469,0.583 false 2.563,1.063 2.979,1.313 0.417,0.25 10 false SST 1.24,1.917 1.469,2.115 0.229,0.198 10 false *1 1.313,0.5 1.542,0.698 0.229,0.198 10 false *1
*1 Nut


Temporarily install 2 nuts to the rear axle hub bolts as shown in the illustration.

Recommended service nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


NOTICE:

Install the nuts to prevent damage to the rear axle hub bolts.



b.

Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.

SST
09611-12010  

NOTICE:

Do not damage the threads of the rear axle hub bolts.



Hide 42312E 10.INSTALL REAR AXLE HUB BOLT

a.
C240541C06
3.063,0.469 3.063,0.125 3.063,0.125 3.167,0.125 false 2.781,0.333 2.781,0.146 2.781,0.146 2.354,0.146 false 3.188,0.042 3.406,0.271 0.219,0.229 10 false *1 2.198,0.063 2.438,0.313 0.24,0.25 10 false *2
*1 Nut
*2 Washer


Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.


b.

Install a washer and nut to the rear axle hub bolt as shown in the illustration.

Recommended service nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


HINT:

Recommended washer thickness is 5 mm (0.197 in.) or more.



c.

Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the nut.

NOTICE:
·

Install the nuts to prevent damage to the rear axle hub bolts.

·

Do not damage the threads of the rear axle hub bolts.




d.

Remove the 3 nuts and washer from the 3 rear axle hub bolts.


Hide 42431 11.INSTALL REAR DISC

Hide 42491 12.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 13.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

a.

Install the rear disc brake caliper assembly with the 2 bolts.

Torque:
62 N*m (630 kgf*cm, 46 ft.*lbf)


b.

Install the rear flexible hose to the rear shock absorber assembly with the bolt.

Torque:
19 N*m (192 kgf*cm, 14 ft.*lbf)


Hide 14.CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

a.

Connect the cable to the negative (-) auxiliary battery terminal.

Click herePower Source / Network>2AR-FXE BATTERY / CHARGING>AUXILIARY BATTERY>INSTALLATION


b.

Connect the reservoir level switch connector.



Hide 55702A 15.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 16.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 17.ADJUST PARKING BRAKE

Hide 18.INSTALL REAR WHEEL

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)