Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function) › 2012.02–2015.04
RM2040EQ _58 Vehicle Interior _014723 THEFT DETERRENT / KEYLESS ENTRY _0075054 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG and ACC)  


DESCRIPTION

If any of the following operations are performed, the power management control ECU receives a signal, and changes the power source mode.

·

With the electrical key transmitter sub-assembly in the cabin, the power switch is pressed.

·

When the transmitter battery of the electrical key transmitter sub-assembly is depleted, the brake pedal is depressed and the electrical key transmitter sub-assembly is held near the power switch.

·

When the smart entry and start system cancel function has been canceled on the customization menu, the brake pedal is depressed and the electrical key transmitter sub-assembly is held near the power switch.


HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


WIRING DIAGRAM

B296602E02
6.51,3.167 6.875,3.615 0.365,0.448 10 false 3C 2.969,1.229 3.344,1.427 0.375,0.198 10 false IG1D 3.427,1.052 3.563,1.219 0.135,0.167 10 false 2 2.896,6.156 3.333,6.354 0.438,0.198 10 false ACCD 3.427,5.958 3.552,6.125 0.125,0.167 10 false 1 4.969,6.458 5.729,6.656 0.76,0.198 10 false ACC NO. 1 4.99,5.104 5.688,5.302 0.698,0.198 10 false IG1 NO. 4 4.99,1.531 5.688,1.729 0.698,0.198 10 false IG1 NO. 1 4.99,2.719 5.688,2.917 0.698,0.198 10 false IG1 NO. 2 4.99,3.896 5.688,4.094 0.698,0.198 10 false IG1 NO. 3 2.24,8.052 3.51,8.365 1.271,0.313 10 false Power Management Control ECU 4.021,8.042 6.708,8.385 2.688,0.344 10 false Instrument Panel Junction Block Assembly 5,7.635 5.76,7.833 0.76,0.198 10 false ACC NO. 2 3.417,6.146 3.74,6.313 0.323,0.167 10 false I4 3.417,1.219 3.74,1.385 0.323,0.167 10 false I4 3.906,1.219 4.146,1.385 0.24,0.167 10 false 3A 3.917,1.042 4.156,1.208 0.24,0.167 10 false 27 6.51,0.813 6.802,1.052 0.292,0.24 10 false 3D 6.542,0.625 6.781,0.792 0.24,0.167 10 false 1 5.948,0.969 6.5,1.167 0.552,0.198 10 false WIPER 5.969,2.177 6.542,2.552 0.573,0.375 10 false ECU-IG1 NO. 1 6.521,1.802 6.802,2.188 0.281,0.385 10 false 36 6.521,2.979 6.844,3.25 0.323,0.271 10 false 33 5.979,3.365 6.573,3.708 0.594,0.344 10 false ECU-IG1 NO. 3 5.948,5.917 6.76,6.125 0.813,0.208 10 false ECU-ACC 6.531,5.552 6.771,5.719 0.24,0.167 10 false 37 6.531,6.708 6.771,6.875 0.24,0.167 10 false 10 6.583,7.229 6.823,7.396 0.24,0.167 10 false 7 5.948,7.073 6.708,7.427 0.76,0.354 10 false P/OUTLET RR 3.896,6.146 4.146,6.313 0.25,0.167 10 false 3B 3.917,5.969 4.156,6.135 0.24,0.167 10 false 23 6.521,1.99 6.813,2.24 0.292,0.25 10 false 3D 6.521,5.729 6.74,5.896 0.219,0.167 10 false 3B 6.521,6.885 6.74,7.052 0.219,0.167 10 false 3B 6.531,7.406 6.75,7.573 0.219,0.167 10 false 3B 3.906,0.802 4.146,0.969 0.24,0.167 10 false 3F 3.948,0.625 4.198,0.792 0.25,0.167 10 false 1 0.115,0.792 0.99,1.104 0.875,0.313 10 false from Auxiliary Battery 1.438,0.938 1.771,1.125 0.333,0.188 10 false AM2 2.521,0.802 2.958,0.948 0.438,0.146 10 false AM21 2.26,0.625 2.375,0.771 0.115,0.146 10 false 7 2.25,0.792 2.458,0.979 0.208,0.188 10 false I4 2.521,1.208 2.958,1.354 0.438,0.146 10 false AM22 2.26,1.021 2.375,1.167 0.115,0.146 10 false 1 2.25,1.198 2.521,1.385 0.271,0.188 10 false I3 2.542,1.875 2.979,2.021 0.438,0.146 10 false E01 2.271,1.667 2.385,1.813 0.115,0.146 10 false 5 2.26,1.865 2.531,2.052 0.271,0.188 10 false I3 2.542,2.271 2.979,2.417 0.438,0.146 10 false E02 2.281,2.063 2.396,2.208 0.115,0.146 10 false 5 2.26,2.26 2.531,2.448 0.271,0.188 10 false I4 2.521,2.688 2.958,2.833 0.438,0.146 10 false E1 2.26,2.479 2.375,2.625 0.115,0.146 10 false 6 2.25,2.656 2.521,2.844 0.271,0.188 10 false I3 2.531,3.083 2.969,3.229 0.438,0.146 10 false E12 2.271,2.875 2.385,3.021 0.115,0.146 10 false 4 2.26,3.063 2.531,3.25 0.271,0.188 10 false I4 0.677,4.927 1.688,5.094 1.01,0.167 10 false Power Switch 0.406,4.917 0.719,5.083 0.313,0.167 10 false I58 1.031,4.094 1.469,4.24 0.438,0.146 10 false SS1 1.031,4.531 1.469,4.677 0.438,0.146 10 false SS2 1.417,3.99 1.531,4.135 0.115,0.146 10 false 5 1.406,4.427 1.521,4.573 0.115,0.146 10 false 1 2.531,4.083 2.969,4.229 0.438,0.146 10 false SSW1 2.531,4.542 2.969,4.688 0.438,0.146 10 false SSW2 2.281,3.885 2.396,4.031 0.115,0.146 10 false 7 2.271,4.073 2.542,4.26 0.271,0.188 10 false I3 2.25,4.344 2.438,4.49 0.188,0.146 10 false 17 2.271,4.51 2.542,4.698 0.271,0.188 10 false I4 2.25,5.813 2.469,5.979 0.219,0.167 10 false 23 2.531,5.99 2.906,6.156 0.375,0.167 10 false STP 2.219,5.99 2.542,6.156 0.323,0.167 10 false A39 1.438,7.24 2.302,7.719 0.865,0.479 10 false from Auxiliary Battery 0.542,6.26 0.854,6.427 0.313,0.167 10 false A33 0.542,6.417 2.313,6.583 1.771,0.167 10 false Stop Light Switch Assembly 0.719,7.385 1.177,7.552 0.458,0.167 10 false STOP 1.573,5.896 1.708,6.063 0.135,0.167 10 false 1 0.792,5.896 0.927,6.063 0.135,0.167 10 false 2

B298915E02
3.797,1.861 4.094,2.054 0.297,0.193 10 IG2 3.085,1.55 3.353,1.715 0.269,0.166 10 1C 3.137,1.37 3.275,1.535 0.138,0.166 10 8 4.64,1.538 4.903,1.704 0.263,0.166 10 1E 4.692,1.372 4.83,1.538 0.138,0.166 10 2 3.286,2.232 4.89,2.425 1.605,0.193 10 No. 1 Integration Relay 0.9,3.231 2.176,3.57 1.276,0.339 10 Power Management Control ECU 1.955,1.55 2.223,1.715 0.269,0.166 10 A39 2.049,1.356 2.186,1.521 0.138,0.166 10 2 1.558,1.554 1.931,1.72 0.373,0.166 10 IG2D

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the electrical key transmitter sub-assembly, refer to the smart entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).

·

Before replacing the power management control ECU, refer to the Service Bulletin.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>DTC CHECK / CLEAR).

·

If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After completing repairs, confirm that the problem does not occur.



HINT:
Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (IG) or on (ACC)
Power Source Control
·

Start Switch1

·

Start Switch2

·

Power Supply Condition

·

IG1 Relay Monitor(Inside)

·

IG2 Relay Monitor(Inside)

·

IG1 Relay Monitor(Outside)

·

IG2 Relay Monitor(Outside)

·

Latch Circuit

·

ACC Relay Monitor


-


PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check the wireless door lock function by operating the electrical key transmitter sub-assembly.

OK:

Wireless door lock function operates.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

GO TO OTHER DIAGNOSTIC PROCEDURE (All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

3.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

3.CHECK HARNESS AND CONNECTOR (GROUND)

OK

4.CHECK SMART ENTRY AND START SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SMART ENTRY AND START SYSTEM
a.

Remove the transmitter battery from the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY>REPLACEMENT


b.
B290532C02
1.115,0.49 0.906,0.24 0.906,0.24 0.573,0.24 false 2.167,1.635 2.24,1.844 2.24,1.844 2.688,1.844 false 0.396,0.167 0.573,0.354 0.177,0.188 10 false *1 2.698,1.76 2.875,1.948 0.177,0.188 10 false *2
*1 Power Switch
*2 Electrical Key Transmitter Sub-assembly


With the brake pedal depressed, hold the electrical key transmitter sub-assembly near the power switch and check if the power source mode changes.

OK:

The power source mode changes.


HINT:

If the power source mode changes, the cabin verification is malfunctioning.



Result:
Result Proceed to
The power source mode does not change. A
The power source mode changes. B



A

5.READ VALUE USING INTELLIGENT TESTER

B

11.READ VALUE USING INTELLIGENT TESTER
5.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the intelligent tester on.


c.

Enter the following menus: Body / Power Source Control / Data List.


d.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The hybrid control system cannot be started when this item is OFF.

·

When this item is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

ON (brake pedal is depressed) and OFF (brake pedal is released) appear on the screen.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING INTELLIGENT TESTER

NG

9.INSPECT STOP LIGHT SWITCH ASSEMBLY
6.READ VALUE USING INTELLIGENT TESTER
a.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state IG2 ON, ST ON, All OFF, IG1 ON or ACC ON All OFF: Power switch off
ACC ON: Power switch on (ACC)
IG1 ON: Power switch on (IG) (IG1 relay on)
IG2 ON: Power switch on (IG) (IG2 relay on)
ST ON: Sending hybrid control system start request signal
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18

b.

With the power switch off and brake pedal depressed, hold the electrical key transmitter sub-assembly near the power switch for 2 seconds or more and read the Data List.

OK:

IG2 ON is displayed in the Data List.


HINT:

If the smart entry and start system function has been canceled on the customization menu, ACC ON is displayed in the Data List.



Result:
Proceed to
OK
NG



OK

7.CHECK POWER MANAGEMENT CONTROL ECU

NG

8.CHECK FOR DTC
7.CHECK POWER MANAGEMENT CONTROL ECU
a.

Read the Data List according to the display on the intelligent tester.


b.
B224008C50
1.208,0.354 1.635,0.646 0.427,0.292 2.396,0.313 2.823,0.604 0.427,0.292 1.583,1.125 1.167,1.813 false 2.823,1.125 2.927,1.833 false 2.76,1.125 2.25,1.833 false 0.073,0.01 0.396,0.198 0.323,0.188 10 false *a 1.281,0.417 1.604,0.604 0.323,0.188 10 false A39 2.531,0.375 2.854,0.563 0.323,0.188 10 false I4 2.729,1.854 3.208,2.042 0.479,0.188 10 false ACCD 0.99,1.813 1.469,2 0.479,0.188 10 false IG2D 2.063,1.833 2.542,2.021 0.479,0.188 10 false IG1D
*a Component with harness connected(Power Management Control ECU)


Measure the voltage according to the value(s) in the table below.


c.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state IG2 ON, ST ON, All OFF, IG1 ON or ACC ON All OFF: Power switch off
ACC ON: Power switch on (ACC)
IG1 ON: Power switch on (IG) (IG1 relay on)
IG2 ON: Power switch on (IG) (IG2 relay on)
ST ON: Sending hybrid control system start request signal
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18

d.

Measure the voltage while checking the Data List on the intelligent tester.

Standard Voltage:
Tester Connection Condition Specified Condition
I4-2 (IG1D) - Body ground Power switch off 1 V or less
Power switch on (ACC) 1 V or less
Power switch on (IG) 9 V or higher
A39-2 (IG2D) - Body ground Power switch off 1 V or less
Power switch on (ACC) 1 V or less
Power switch on (IG) 9 V or higher
I4-1 (ACCD) - Body ground Power switch off 1 V or less
Power switch on (IG) 8.5 V or higher
Power switch on (ACC) 8.5 V or higher



Result:
Proceed to
OK
NG



OK

CHECK RELAY CONTACT SIDE CIRCUIT

NG

8.CHECK FOR DTC
a.

Enter the following menus: for Entry&Start: Body / Entry&Start / Trouble Codes.


b.

Check for DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 223

Result:
Result Proceed to
The following DTCs are not output:
·

B2785

·

B2287

·

B2784

·

B278A


A
DTC B2785 is not output but DTC B2287 is output. B
DTCs other than B2287 are output. C



A

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

C

GO TO OTHER DIAGNOSTIC PROCEDURE

9.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Disconnect the A33 connector from the stop light switch assembly.


b.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.READ VALUE USING INTELLIGENT TESTER
a.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Start Switch1 Power switch 1 status ON or OFF ON: Power switch pressed
OFF: Power switch not pressed
·

If the power switch is pressed for a short time, the display may not change.

·

Use this item to determine whether the power switch input signal is malfunctioning.


Start Switch2 Power switch 2 status ON or OFF ON: Power switch pressed
OFF: Power switch not pressed
·

Backup for power switch 1. However, when the power switch is pressed and held, the control functions only when both power switch 1 and 2 are normal.

·

Behaves the same way as power switch 1.


Body Electrical > Power Source Control > Data List
Tester Display
Start Switch1
Start Switch2
50003 223 4,5
OK:

ON (Power switch is pressed) and OFF (Power switch is not pressed) appear on the screen.



Result:
Result Proceed to
NG A
OK B



A

12.INSPECT POWER SWITCH

B

12.INSPECT POWER SWITCH

Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - POWER SWITCH)

NG

13.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - POWER SWITCH)
a.

Disconnect the I3 and I4 connector from the power management control ECUs.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I3-7 (SSW1) - I58-5 (SS1) Always Below 1 Ω
I4-17 (SSW2) - I58-1 (SS2) Always Below 1 Ω
I3-7 (SSW1) or I58-5 (SS1) - Body ground Always 10 kΩ or higher
I4-17 (SSW2) or I58-1 (SS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR