Make sure to select FACE mode before disconnecting the cable from the negative (-) auxiliary battery terminal.
1. RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM
2.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
55702A
3.REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY
87246
4.DISCONNECT HEATER OUTLET WATER HOSE
Using pliers, grip the claws of the clip and slide the clip to disconnect the heater outlet water hose.
Do not apply excessive force to the heater outlet water hose.
Prepare a drain pan or cloth in case the coolant leaks.
87245
5.DISCONNECT HEATER INLET WATER HOSE
Using pliers, grip the claws of the clip and slide the clip to disconnect the heater inlet water hose.
Do not apply excessive force to the heater inlet water hose.
Prepare a drain pan or cloth in case the coolant leaks.
88704
6.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
Remove the bolt, and rotate the hook connector.
Disconnect the suction hose sub-assembly.
Remove the O-ring from the suction hose sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
88710E
7.DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY
Disconnect the air conditioner tube and accessory assembly.
Remove the O-ring from the air conditioner tube and accessory assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
8.REMOVE FRONT SEAT ASSEMBLY RH
9.REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)
10.REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)
Use the same procedure as for the RH side.
86183D
11.REMOVE AUDIO AMPLIFIER COVER (for 10 Speakers)
12.REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET (for 10 Speakers)
13.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
14.REMOVE STEERING POST ASSEMBLY
82877
15.REMOVE ECU INTEGRATION BOX RH
89681A
16.REMOVE POWER MANAGEMENT CONTROL ECU
82730
17.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
88650N
18.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY
85940
19.REMOVE WINDSHIELD WIPER RELAY ASSEMBLY (w/ Rain Sensor)
58521B
20.REMOVE FLOOR CARPET HOOK
| *A | for RH Side |
| *B | for LH Side |
Disengage the 6 guides.
| *A | for RH Side |
| *B | for LH Side |
Disengage the 6 claws and remove the 6 floor carpet hooks.
77306
21.DISCONNECT FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
Remove the screw.
Disengage the guide to disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.
58569D
22.REMOVE FRONT FLOOR CAUTION PLATE COVER
Using a moulding remover, disengage the claw and guide, and remove the front floor caution plate cover.
58543B
23.REMOVE FLOOR CARPET BRACKET RH
Disengage the guide.
Turn back the floor carpet as shown in the illustration.
Remove the 2 clips.
Disengage the 2 guides to remove the floor carpet bracket RH.
87212
24.REMOVE REAR NO. 1 AIR DUCT
Disengage the 2 claws to remove the rear No. 1 air duct.
58544A
25.REMOVE FLOOR CARPET BRACKET LH
Disengage the guide.
Turn back the floor carpet as shown in the illustration.
Remove the 2 clips.
Disengage the 2 guides to remove the floor carpet bracket LH.
87212F
26.REMOVE REAR NO. 2 AIR DUCT
Disengage the 2 claws to remove the rear No. 2 air duct.
58861B
27.REMOVE NO. 1 CONSOLE BOX DUCT
Remove the clip and the No. 1 console box duct.
88625Q
28.REMOVE ROOM TEMPERATURE SENSOR (COOLER THERMISTOR)
Disconnect the cooler thermistor hose and connector, and remove the room temperature sensor (cooler thermistor).
55307E
29.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
| *1 | Earth Wire |
Disconnect the connector.
Disengage each clamp.
Remove the bolt and disconnect the earth wire.
Remove the bolt and 2 nuts.
Remove the screw and No. 2 instrument panel brace sub-assembly.
55306B
30.REMOVE INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY
| *1 | Earth Wire |
Disconnect the connector.
Disengage each clamp.
Remove the bolt and disconnect the earth wire.
Remove the bolt and 2 nuts.
Remove the screw and instrument panel to cowl brace sub-assembly.
55458A
31.REMOVE INSTRUMENT PANEL SAFETY PAD CAP
Put protective tape around the 5 instrument panel safety pad caps.
| *A | for Driver Side | *B | for Passenger Side |
| *1 | Protective Tape | - | - |
Using a screwdriver, remove the 5 instrument panel safety pad caps.
32.REMOVE FRONT LOWER PANEL PACKING
Remove the 2 front lower panel packings as shown in the illustration.
33.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT
Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.
When disassembling the air conditioning unit, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
for 10 Speakers:
Disengage the 3 clamps.
Remove the bolt.
Disconnect the connector.
Disengage 3 clamps to open the 3 clamps as shown in the illustration.
| *1 | Airbag Sensor Assembly |
Disconnect the connector from the airbag sensor assembly as shown in the illustration.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Disconnect each connector.
Disengage each clamp.
Using a screwdriver, disengage the 2 claws to unlock the retainer as shown in the illustration.
| *1 | Retainer | *2 | Protective Tape |
Disengage the claw and disconnect the airbag connector as shown in the illustration.
Disengage each clamp.
| *1 | Earth Wire | *2 | Connector Holder |
Remove the 3 bolts and disconnect the 3 earth wires.
Remove the 2 nuts and disconnect the connector holder.
Disconnect the connector.
Remove the 2 bolts.
Remove the 5 bolts and nut as shown in the illustration.
| *1 | Movable Collar | *2 | Body |
| *3 | Instrument Panel Reinforcement | - | - |
| *a | Step 1 | *b | Step 2 |
| *c | Step 3 | *d | Step 4 |
Remove the bolt.
Disconnect the drain cooler hose.
Disengage the 3 guides and remove the instrument panel reinforcement with air conditioning unit as shown in the illustration.
34.REMOVE AIR CONDITIONING UNIT ASSEMBLY
Remove the 3 bolts and air conditioning unit assembly from the instrument panel reinforcement assembly.