Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge) › 2012.02–2015.04
RM2040EQ _53 Suspension _014705 FRONT SUSPENSION _0283163 FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge) A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge)  REMOVAL  


PROCEDURE

Hide 1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.SECURE STEERING WHEEL

Hide 3.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide G9019 4.REMOVE INVERTER TRAY BRACKET SUB-ASSEMBLY

a.
C243604

Remove the 4 bolts and inverter tray bracket sub-assembly.


Hide 5.REMOVE FRONT WHEELS

Hide 53852K 6.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 51442C 7.REMOVE ENGINE UNDER COVER LH

Hide 53851Z 8.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 51441C 9.REMOVE ENGINE UNDER COVER RH

Hide 53737B 10.REMOVE FRONT FENDER APRON SEAL LH

Hide 53736 11.REMOVE FRONT FENDER APRON SEAL RH

Hide 12.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 13.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 53866J 14.REMOVE FRONT FENDER TO COWL SIDE SEAL RH

Hide 53867H 15.REMOVE FRONT FENDER TO COWL SIDE SEAL LH

HINT:

Use the same procedure as for the RH side.


Hide 55781E 16.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 12601B 17.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 17410 18.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 43502H 19.REMOVE FRONT AXLE SHAFT NUT LH

Hide 43501H 20.REMOVE FRONT AXLE SHAFT NUT RH

HINT:

Perform the same procedure as for the LH side


Hide 48810 21.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 22.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side


Hide 45470 23.SEPARATE TIE ROD ASSEMBLY LH

Hide 45460 24.SEPARATE TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side


Hide 48069 25.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 26.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side


Hide 43420 27.SEPARATE FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43410 28.SEPARATE FRONT DRIVE SHAFT ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side


Hide 45220 29.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 12361A 30.SEPARATE FRONT ENGINE MOUNTING INSULATOR

a.
A209884

Remove the 3 nuts and separate the front engine mounting insulator from the front frame assembly.


Hide 12372A 31.SEPARATE ENGINE MOUNTING INSULATOR LH

a.

Remove the 2 hole plugs.


b.
A353344

Remove the 3 nuts and separate the engine mounting insulator LH from the front frame assembly.


Hide 12362 32.SEPARATE ENGINE MOUNTING INSULATOR RH

a.

Remove the 2 hole plugs.


b.
A209885

Remove the 3 nuts and separate the engine mounting insulator RH from the front frame assembly.


Hide 12327A 34.REMOVE NO. 2 ENGINE MOUNTING STAY RH

Hide 36.INSTALL ENGINE SUPPORT BRIDGE

a.
C312139

Disengage the 2 clamps.


b.

Remove the 2 hood support assemblies.

Click hereVehicle Exterior>DOOR / HATCH>HOOD SUPPORT>REMOVAL


c.

Install SST to the vehicle body as shown in the illustration.

SST
09940-10010  

U124724C02
2.875,5.854 1.74,5.854 true 5.521,5.854 4.302,5.854 true 5.698,6.771 5.573,7.021 5.573,7.021 5.49,7.021 false 1.656,6.729 1.802,7.021 1.802,7.021 1.896,7.021 false 2.167,2.438 2.229,2.302 2.229,2.302 2.323,2.302 false 5.031,2.573 4.927,2.375 4.927,2.375 4.844,2.375 true 5.896,8.188 5.813,7.938 5.813,7.938 5.729,7.938 false 5.063,8.188 4.99,7.938 4.99,7.938 4.906,7.938 false 2.083,8.188 2.167,7.938 2.167,7.938 2.25,7.938 false 1.219,8.188 1.292,7.938 1.292,7.938 1.385,7.938 false 5.802,2.719 6.583,2.719 true 4.146,5.771 4.354,5.979 0.208,0.208 10 false *a 2.896,5.76 3.104,5.969 0.208,0.208 10 true *a 5.313,6.948 5.521,7.156 0.208,0.208 10 false *b 1.927,6.948 2.135,7.156 0.208,0.208 10 false *b 2.344,2.229 2.552,2.438 0.208,0.208 10 false *c 4.667,2.302 4.875,2.51 0.208,0.208 10 true *c 5.552,7.875 5.76,8.083 0.208,0.208 10 false *b 4.729,7.875 4.938,8.083 0.208,0.208 10 false *b 2.281,7.875 2.49,8.083 0.208,0.208 10 false *b 1.406,7.875 1.615,8.083 0.208,0.208 10 false *b 0.938,6.979 1.146,7.188 0.208,0.208 10 false *e 2.51,6.979 2.719,7.188 0.208,0.208 10 false *f 4.542,6.99 4.75,7.198 0.208,0.208 10 false *f 6.063,6.99 6.271,7.198 0.208,0.208 10 false *e 0.927,1.885 1.135,2.094 0.208,0.208 10 false *d 0.615,0.906 0.823,1.115 0.208,0.208 10 false *g 6.031,1.885 6.24,2.094 0.208,0.208 10 false *d 6.313,0.906 6.521,1.115 0.208,0.208 10 false *g 6.625,2.635 6.958,2.844 0.333,0.208 10 false SST
*a Support Shaft *b Side Member
*c Cloth *d Front Side
*e Correct *f Incorrect
*g Front Suspension Nut - -


CAUTION:
·
C312303C05
1.761,2.043 1.964,2.235 0.203,0.191 10 *a 0.175,1.885 0.378,2.076 0.203,0.191 10 *a 0.57,0.075 0.773,0.266 0.203,0.191 10 *c 2.261,0.075 2.464,0.266 0.203,0.191 10 *d 0.136,2.338 0.340,2.530 0.203,0.191 10 *b 1.74,2.46 1.944,2.651 0.203,0.191 10 *b 0.405,1.987 0.51,1.987 0.51,1.987 0.797,2.456 false 0.35,2.426 0.465,2.426 0.465,2.426 0.781,2.709 false 1.991,2.133 2.078,2.133 2.078,2.133 2.475,2.448 false 1.971,2.545 2.091,2.545 2.091,2.545 2.477,2.723 false
*a Fuse Shackle
*b Shackle (A)
*c Correct
*d Incorrect


Make sure the fuse shackle is on the chain block side and the shackle (A) is on the division bar side as shown in the illustration so that the fuse bolt is visible and can be checked for deformation easily.

·
C316804C03
1.396,1.052 1,1.052 false 0.792,0.969 1,1.156 0.208,0.188 10 false *a 0.854,1.802 1.063,1.99 0.208,0.188 10 false *b 2.354,1.802 2.563,1.99 0.208,0.188 10 false *c
*a Fuse Bolt
*b Correct
*c Incorrect


Make sure the fuse bolt is not deformed.



NOTICE:
·

Prevent SST from contacting the vehicle body or windshield.

·

To prevent damage to the engine hood, place pieces of cloth between the engine hood and SST.

·

Lightly shake SST by hand to make sure it is securely installed while performing work.

·

Set the support shafts on level surfaces.




d.
C312305C03
1.386,2.029 1.586,2.235 0.199,0.206 10 *a 1.913,2.338 2.112,2.544 0.199,0.206 10 *d 0.478,2.422 0.678,2.628 0.199,0.206 10 *c 0.253,0.975 0.452,1.181 0.199,0.206 10 *b 1.059,2.145 1.361,2.145 false 1.017,2.463 1.896,2.463 false 0.704,2.522 0.792,2.522 0.792,2.522 0.859,2.768 false 0.478,1.067 0.566,1.067 0.566,1.067 0.641,1.479 false
*a Support Shaft
*b Sub Beam
*c Side Member
*d Threaded Portion


Turn the threaded portion of each support shaft to adjust its height and make the sub beams parallel to the ground.


e.

Connect each chain to the division bar with the shackles at the positions shown in the illustration.

C316206C03
1.625,1.26 1.708,0.823 1.708,0.823 1.781,0.823 true 1.469,1.688 1.021,2.563 1.021,2.563 0.948,2.563 true 1.385,1.583 0.313,1.583 true 0.781,3.677 0.667,3.083 0.667,3.083 0.594,3.083 true 2.427,4.281 1.854,4.281 true 1.833,3.906 2.177,3.906 false 1.813,0.729 2.021,0.948 0.208,0.219 10 false *a 0.792,2.479 1,2.698 0.208,0.219 10 false *c 0.156,1.5 0.365,1.719 0.208,0.219 10 false *1 0.427,3 0.635,3.219 0.208,0.219 10 false *a 2.448,4.198 2.656,4.417 0.208,0.219 10 true *2 2.198,3.833 2.406,4.052 0.208,0.219 10 true *b
*1 No. 1 Engine Hanger *2 No. 2 Engine Hanger
*a Division Bar *b Shackle (A)
*c Shackle (B) - -



f.

Connect the division bar and No. 1 engine hanger with the shackle (B).


g.

Connect the 1st link of the chain to the No. 2 engine hanger.


h.

Make sure the distance between the chain block assembly and suspension ring is 20 mm (0.787 in.) or more.

C316207C02
1.573,1.427 1.5,1.542 1.5,1.542 1.333,1.542 false 1.833,1.26 1.906,1.375 1.906,1.375 2.073,1.375 false 2.083,1.292 2.302,1.5 0.219,0.208 10 false *a 1.156,1.167 1.375,1.375 0.219,0.208 10 false *c 1.188,1.448 1.406,1.656 0.219,0.208 10 false *b
*a Chain Block Assembly *b Suspension Ring
*c 20 mm (0.787 in.) or more - -



i.

Adjust the position of the chain block assembly so that the chain is perpendicular to the main beam and sub beams as shown in the illustration.

C316208C02
3.979,0.729 4.063,0.427 4.063,0.427 4.156,0.427 false 1.677,2.094 1.073,2.094 true 6.104,2.115 5.5,2.115 true 3.25,1.146 2.99,1.146 false 2.833,1.042 3.042,1.25 0.208,0.208 10 false *a 3.365,0.333 3.573,0.542 0.208,0.208 10 false *h 4.188,0.333 4.396,0.542 0.208,0.208 10 false *b 1.615,0.281 1.823,0.49 0.208,0.208 10 true *d 5.365,0.281 5.573,0.49 0.208,0.208 10 true *e 1.5,1.406 1.708,1.615 0.208,0.208 10 false *i 5.604,1.385 5.813,1.594 0.208,0.208 10 false *i 0.906,1.99 1.115,2.198 0.208,0.208 10 false *c 6.125,2.01 6.333,2.219 0.208,0.208 10 false *c 1.281,3.458 1.49,3.667 0.208,0.208 10 false *f 4.646,3.385 4.854,3.594 0.208,0.208 10 false *g
*a Chain Block Assembly *b Main Beam
*c Sub Beam *d Dimension (A)
*e Dimension (B) *f Correct
*g Incorrect *h Right to Left Adjustment
*i Front to Rear Adjustment - -


CAUTION:

To prevent the engine assembly with hybrid vehicle transaxle assembly from falling, make sure that the dimension (A) and dimension (B) are equal.



j.

Tighten the 6 wing bolts and 2 bolts.

C316209

Torque:
Bolt : 30 N*m (306 kgf*cm, 22 ft.*lbf)


k.
C316210C02
1.369,0.782 1.608,0.993 0.239,0.211 10 *a
*a Approximately 50 mm (1.97 in.)


Move the chain block assembly approximately 50 mm (1.97 in.) as shown in the illustration.


l.
C316211C02
2.672,3.238 2.881,3.436 0.209,0.198 10 *a
*a Turn


Tighten the chain block assembly until it cannot be moved any further by hand.

CAUTION:
C316805C05
1.198,0.927 1.469,0.927 false 3.021,0.917 3.177,0.917 false 0.479,2.333 0.479,2.583 false 2.302,2.469 2.302,2.719 false 0.365,1.396 0.125,1.635 0.125,1.635 0.125,1.875 false 2.177,1.406 1.938,1.646 1.938,1.646 1.938,1.885 false 3.219,0.844 3.406,1.052 0.188,0.208 10 false *a 1.5,0.865 1.688,1.073 0.188,0.208 10 false *a 0.042,1.885 0.229,2.094 0.188,0.208 10 false *c 0.406,2.594 0.594,2.802 0.188,0.208 10 false *b 1.875,1.896 2.063,2.104 0.188,0.208 10 false *c 2.219,2.74 2.406,2.948 0.188,0.208 10 false *b 0.625,0.25 0.813,0.458 0.188,0.208 10 false *d 2.448,0.25 2.635,0.458 0.188,0.208 10 false *e
*a Chain Block Assembly
*b Suspension Ring
*c Roller
*d Incorrect
*e Correct


If the suspension ring contacts the roller of the chain block assembly, the chain block assembly may be damaged. Do not tighten the chain block assembly excessively.


NOTICE:
·

When suspending the engine assembly with hybrid vehicle transaxle assembly, do not tighten the chain block assembly more than 50 N*m (510 kgf*cm, 37 ft.*lbf).

·

Do not shake the engine assembly with hybrid vehicle transaxle assembly excessively while it is being suspended.




Hide 37.INSTALL BELT

a.
C363135

Remove the bolt and nut.


b.
C363136

Loosen the bolt and disconnect the windshield washer jar assembly from the vehicle body.

NOTICE:

Do not remove the bolt.



c.

Install SST to the vehicle body as shown in the illustration.

SST
09727-00110  

C313717N01
3.823,4.115 6.115,4.115 true 3.323,4.115 1.031,4.115 true 6.146,4.031 6.5,4.229 0.354,0.198 10 false SST 0.74,4.031 1.094,4.229 0.354,0.198 10 false SST


d.

Using the ratchet buckle, tighten the belt until there is no slack.

U124721C01
3.698,2.156 6.104,2.156 true 3.458,2.156 1.094,2.156 true 2.583,1.083 2.365,1.552 2.365,1.552 2.25,1.552 true 4.542,1.063 4.781,1.563 4.781,1.563 4.896,1.563 true 6.146,2.073 6.5,2.271 0.354,0.198 10 false SST 0.802,2.073 1.156,2.271 0.354,0.198 10 false SST 4.927,1.51 5.156,1.729 0.229,0.219 10 true *a 2.073,1.458 2.302,1.677 0.229,0.219 10 true *a
*a Ratchet Buckle - -



Hide 51100G 38.REMOVE FRONT FRAME ASSEMBLY

a.
C310542

Disconnect the 2 clamps.


b.
C319461C02
1.454,0.662 1.174,0.662 false 0.98,0.562 1.211,0.700 0.230,0.138 10 *a
*a Chain Block Assembly


Wind the chain with the chain block assembly to lift the engine with hybrid vehicle transaxle assembly.

NOTICE:
·

When suspending the engine with hybrid vehicle transaxle assembly, do not tighten the chain block assembly more than 50 N*m (510 kgf*cm, 37 ft.*lbf).

·

Lift the engine with hybrid vehicle transaxle assembly until the engine is slightly raised off the front frame assembly.

·

Do not lift the engine with hybrid vehicle transaxle assembly excessively.




c.
C311098C01
0.406,0.76 0.406,1.01 true 1.365,0.51 1.365,0.917 true 0.896,0.542 0.896,0.656 0.896,0.656 1.365,0.656 true 2.427,0.5 2.427,0.927 true 2.677,0.531 2.677,0.667 2.677,0.667 2.427,0.667 true 0.323,1.021 0.5,1.177 0.177,0.156 10 false *a 1.281,0.927 1.458,1.083 0.177,0.156 10 false *b 2.344,0.927 2.521,1.083 0.177,0.156 10 false *b
*a Engine Lifter
*b Attachment
V100145

Attachment Placement Location


Support the front frame assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

CAUTION:
·

The front frame assembly is a heavy component. Make sure that it is supported securely.

·

Make sure to secure the front frame assembly to prevent it from dropping.



NOTICE:

Use the attachments to keep the front frame assembly level.



d.
A260218

Remove the 4 bolts, 2 nuts and frame side rail plates RH and LH.


e.

Remove the 4 bolts, 2 nuts and front suspension member rear braces RH and LH.


f.

Slowly lower the front frame assembly.

NOTICE:

When lowering the front frame assembly, be careful not to damage the vehicle body or other components installed to the vehicle.



Hide 48829A 39.REMOVE FRONT NO. 1 STABILIZER BRACKET LH

Hide 48824A 40.REMOVE FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as the LH side.


Hide 41.REMOVE FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY

a.

Remove the front stabilizer bar with 2 front stabilizer link assemblies from the front frame assembly.


Hide 42.REMOVE STEERING LINK ASSEMBLY

Hide 48069 43.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C167143

Remove the 3 bolts, nut and front lower No. 1 suspension arm sub-assembly from the front frame assembly.

NOTICE:

When removing the bolt, keep the nut from rotating.



b.

Remove the front lower arm bushing stopper from the front lower No. 1 suspension arm sub-assembly.


Hide 48068 44.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.


Hide 51227B 45.REMOVE FRONT SUSPENSION MEMBER DYNAMIC DAMPER

a.
C221242

Remove the 2 bolts and front suspension member dynamic damper from the front frame assembly.


Hide 52213A 46.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER

a.

Remove the 2 front suspension member body mounting front stoppers from the front frame assembly.


Hide 52216B 47.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER

a.

Remove the 2 front suspension member body mounting rear stoppers from the front frame assembly.


Hide 52211J 48.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION

a.
C169231C09
1.208,1 1.385,1 1.385,1 1.5,1.427 false 1.917,0.823 2.313,0.823 false 2.729,2.177 2.281,2.177 false 2.552,2.875 2.615,2.875 2.615,2.875 2.615,2.177 false 1.042,0.917 1.271,1.198 0.229,0.281 10 false *1 2.365,0.729 2.771,1.01 0.406,0.281 10 false SST 2.771,2.094 3.156,2.333 0.385,0.24 10 false SST
*1 Front Suspension Member Body Mounting Front Cushion


Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04020, 09952-04010, 09954-04010, 09955-04011, 09958-04011)


b.
C265514C03
0.698,2.99 1,2.99 false 2.823,0.719 2.823,0.469 false 2.594,2.917 2.896,2.917 false 0.417,2.917 0.875,3.115 0.458,0.198 10 false SST 2.74,0.708 2.938,0.917 0.198,0.208 10 false *a 2.927,2.844 3.125,3.052 0.198,0.208 10 false *b
*a Turn
*b Hold


Using SST, remove the front suspension member body mounting front cushion from the front frame assembly.

NOTICE:
·

Make sure that the claws of SST are securely hung onto the mounting cushion.

·

Tighten SST slowly and evenly.

·

Be careful as the mounting cushion may fly out.

·

The mounting cushion cannot be reused.




Hide 52217E 49.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH

a.
C169231C10
1.198,1 1.375,1 1.375,1 1.49,1.427 false 1.917,0.823 2.313,0.823 false 2.74,2.177 2.292,2.177 false 2.563,2.875 2.625,2.875 2.625,2.875 2.625,2.177 false 1.021,0.917 1.271,1.177 0.25,0.26 10 false *1 2.354,0.729 2.823,0.99 0.469,0.26 10 false SST 2.781,2.083 3.25,2.396 0.469,0.313 10 false SST
*1 Front Suspension Member Body Mounting Rear Cushion LH


Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04020, 09952-04010, 09954-04010, 09955-04011, 09958-04011)


b.
C265515C03
0.677,3.031 0.99,3.031 false 2.708,0.781 2.708,0.427 false 2.677,2.917 2.99,2.917 false 0.396,2.969 0.854,3.167 0.458,0.198 10 false SST 2.625,0.781 2.938,0.938 0.313,0.156 10 false *a 3.01,2.854 3.323,3.01 0.313,0.156 10 false *b
*a Turn
*b Hold


Using SST, remove the front suspension member body mounting rear cushion LH from the front frame assembly.

NOTICE:
·

Make sure that the claws of SST are securely hung onto the mounting cushion.

·

Tighten SST slowly and evenly.

·

Be careful as the mounting cushion may fly out.

·

The mounting cushion cannot be reused.




Hide 52215 50.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION RH

HINT:

Perform the same procedure as the LH side.


Hide 51.REMOVE HOLE PLUG

a.

Remove 5 hole plugs from the front frame assembly.