Home › Engine / Hybrid System ยท 6AR-FSE › ENGINE MECHANICAL › ENGINE

ENGINE > ON-VEHICLE INSPECTION

for Preparation Click here



1. INSPECT ENGINE COOLANT
(Click here)


2. INSPECT ENGINE OIL
(Click here)


3. CHECK BATTERY CONDITION
(Click here)


4. INSPECT SPARK PLUG
(Click here)


5. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Remove the air cleaner filter element sub-assembly.

  1. Visually check that the air cleaner filter element sub-assembly is not excessively damaged or oily. If necessary, replace the air cleaner filter element sub-assembly.

    HINT:
    1. If there is any dirt or clogs in the air cleaner filter element sub-assembly, clean it with compressed air.
    2. If any dirt or clogs remain even after cleaning the air cleaner filter element sub-assembly with compressed air, replace it.

  1. Install the air cleaner filter element sub-assembly.



6. INSPECT V-RIBBED BELT


    B000543
  1. Check the V-ribbed belt for wear, cracks or other signs of damage.
    If any of the following defects is found, replace the V-ribbed belt.

    1. The V-ribbed belt is cracked.
    2. The V-ribbed belt is worn out to the extent that the cords are exposed.
    3. The V-ribbed belt has chunks missing from the ribs.



    A087787E20
  1. Check that the V-ribbed belt fits properly in the ribbed grooves.
    Text in Illustration 
    *a
    Correct
    *b
    Incorrect

    HINT:
    Check with your hand to confirm that the V-ribbed belt has not slipped out of the grooves on the bottom of the pulley. If it has slipped out, replace the V-ribbed belt. Install a new V-ribbed belt correctly.



7. INSPECT V-RIBBED BELT TENSIONER ASSEMBLY
  1. Remove the V-ribbed belt (Click here).

  1. Check that nothing is caught in the V-ribbed belt tensioner assembly by turning it clockwise and counterclockwise.

    HINT:
    If a malfunction exists, replace the V-ribbed belt tensioner assembly.

  1. Install the V-ribbed belt (Click here).



8. INSPECT VALVE LASH ADJUSTER ASSEMBLY NOISE
  1. Rev up the engine several times. Check that the engine does not emit unusual noises.

  1. If unusual noises occur, warm up the engine and idle it for 30 minutes or more, then perform the inspection.

    HINT:
    If any defects or problems are found during the inspection, perform valve lash adjuster assembly inspection .



9. INSPECT IGNITION TIMING
  1. Warm up and stop the engine.

  1. When using the GTS:

    1. Connect the GTS to the DLC3.

    2. Start the engine and run it at idle.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Data List / Ignition Timing Cylinder #1.

      Standard Ignition Timing:
      5 to 15° BTDC at idle

      NOTICE:
      1. Check the ignition timing with the cooling fans off.
      2. Turn off all electrical systems and the A/C.
      3. When checking the ignition timing, the transaxle should be in neutral or park.

    5. Check that the ignition timing advances immediately when the engine speed is increased.

    6. Enter the following menus: Powertrain / Engine / Active Test / Activate the TC Terminal / ON.

    7. Monitor Ignition Timing Cylinder #1.

    8. Perform the Active Test.

      Standard Ignition Timing:
      8 to 12° BTDC at idle

      NOTICE:
      1. Check the ignition timing with the cooling fans off.
      2. Turn off all electrical systems and the A/C.
      3. When checking the ignition timing, the transaxle should be in neutral or park.



  1. When not using the GTS:



      A122830E44
    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
      Text in Illustration 
      *a
      DLC3

      SST
      09843-18040  

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connecting the wrong terminals may damage electrical components.
      2. Check the ignition timing with the cooling fans off.
      3. Turn off all electrical systems and the A/C.
      4. When checking the ignition timing, the transaxle should be in neutral or park.

    2. Remove the No. 1 engine cover sub-assembly .



    3. A338458
    4. Connect the clip of a timing light to the ignition coil wire for the No. 1 cylinder.

      NOTICE:
      Use a timing light that detects primary signals.

    5. Start the engine and run it at idle.

    6. Check the ignition timing at idle.

      Standard Ignition Timing:
      8 to 12° BTDC at idle

      NOTICE:
      1. Check the ignition timing with the cooling fans off.
      2. Turn off all electrical systems and the A/C.
      3. When checking the ignition timing, the transaxle should be in neutral or park.

    7. Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

    8. Check the ignition timing at idle.

      Standard Ignition Timing:
      5 to 15° BTDC at idle

      NOTICE:
      1. Check the ignition timing with the cooling fans off.
      2. Turn off all electrical systems and the A/C.
      3. When checking the ignition timing, the transaxle should be in neutral or park.

    9. Confirm that the ignition timing advances immediately when the engine speed is increased.

    10. Disconnect the clip of the timing light from the ignition coil wire for the No. 1 cylinder.

    11. Install the No. 1 engine cover sub-assembly .



10. INSPECT ENGINE IDLE SPEED
  1. Warm up and stop the engine.

  1. When using the GTS:

    1. Connect the GTS to the DLC3.

    2. Start the engine and run it at idle.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

    5. Read the value displayed on the tester.

      Standard Idle Speed:
      600 to 700 rpm

      NOTICE:
      1. Check the engine idle speed with the cooling fans off.
      2. Turn off all electrical systems and the A/C.
      3. When checking the engine idle speed, the transaxle should be in neutral or park.



  1. When not using the GTS:



      A122830E45
    1. Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.
      Text in Illustration 
      *a
      DLC3

      SST
      09843-18030  

      NOTICE:
      Be sure to connect the tachometer probe to the correct terminal. Connecting the wrong terminals can cause damage to electrical components.

    2. Start the engine and run it at idle.

    3. Inspect the engine idle speed.

      Standard Idle Speed:
      600 to 700 rpm

      NOTICE:
      1. Check the engine idle speed with the cooling fans off.
      2. Turn off all electrical systems and the A/C.
      3. When checking the engine idle speed, the transaxle should be in neutral or park.

    4. Turn the engine switch off.

    5. Disconnect the tachometer probe from terminal 9 (TAC) of the DLC3.



11. INSPECT COMPRESSION

NOTICE:
Keep the spark plug holes free of foreign matter when measuring the compression pressure.

  1. Warm up and stop the engine.

  1. Check for DTCs (Click here).

  1. Remove the 4 spark plugs (Click here).

  1. Remove the air cleaner cap with air cleaner hose .

  1. Remove the air cleaner case sub-assembly .



    A338460
  1. Disconnect the fuel injector connector (for Port Injection).



    A339264
  1. Disconnect the fuel injector connector (for Direct Injection).

  1. Install the air cleaner case sub-assembly .

  1. Install the air cleaner cap with air cleaner hose .



    A338459
  1. Check the cylinder compression pressure.

    1. Insert a compression gauge into the spark plug hole.

    2. Fully open the throttle.

    3. While cranking the engine, measure the compression pressure.

      Standard Compression Pressure:
      1400 kPa (14.3 kgf/cm2, 203 psi)

      Minimum Compression Pressure:
      980 kPa (10.0 kgf/cm2, 142 psi)

      Pressure Difference between Each Cylinder:
      100 kPa (1.0 kgf/cm2, 15 psi) or less

      NOTICE:
      1. Always use a fully charged battery to obtain an engine speed of 250 rpm or more.
      2. Inspect the other cylinders in the same way.
      3. Measure the compression pressure as quickly as possible.

  1. If the cylinder compression pressure is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect it again.

    HINT:
    1. If adding engine oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.
    2. If the compression pressure stays low, a valve may be stuck or seated improperly, or there may be leaks in the cylinder head gasket.

  1. Remove the air cleaner cap with air cleaner hose.

  1. Remove the air cleaner case sub-assembly.

  1. Connect the fuel injector connector (for Direct Injection).

  1. Connect the fuel injector connector (for Port Injection).

  1. Install the air cleaner case sub-assembly .

  1. Install the air cleaner cap with air cleaner hose .

  1. Install the 4 spark plugs (Click here).

  1. Clear the DTCs (Click here).

    NOTICE:
    After the inspection, clear the DTCs, check for DTCs again and make sure the normal system code is output.



12. INSPECT CO/HC

HINT:
This check determines whether or not the idle CO/HC complies with regulations.

  1. Start the engine.

  1. Run the engine at 2500 rpm for approximately 180 seconds.

  1. Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idle.

  1. Immediately check the CO/HC concentration during idle and when the engine is running at 2500 rpm.

    HINT:
    When performing a 2 mode (with the engine idling/running at 2500 rpm) test, the measurement procedures are determined by applicable local regulations. If the CO/HC concentration does not comply with the regulations, perform troubleshooting in the order given below.


    1. Check for DTCs (Click here).

    2. See the following table for possible causes, then inspect the applicable parts and repair them if necessary.

      CO
      HC
      Problem
      Cause
      Normal
      High
      Rough idle
      1. Faulty ignition:
        1. Incorrect valve timing
        2. Fouled, shorted or improperly gapped spark plugs
      2. Incorrect valve clearance (valve lash adjuster assembly)
      3. Leaks in intake or exhaust valves
      4. Leaks in cylinders
      5. Faulty EGR
      Low
      High
      Rough idle
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        2. Intake manifold
        3. Throttle with motor body assembly
        4. Brake booster line
      2. Lean mixture causing misfire
      3. Faulty EGR
      High
      High
      Rough idle (Black smoke from exhaust)
      1. Restricted air cleaner filter element sub-assembly
      2. Plugged PCV valve
      3. Faulty SFI system:
        1. Fuel pressure regulator assembly
        2. Engine coolant temperature sensor
        3. Mass air flow meter sub-assembly
        4. ECM
        5. Fuel injector assemblies
        6. Throttle position sensor (built into throttle with motor body assembly)
      4. Faulty EGR