Home › Engine / Hybrid System › 2AR-FE (ENGINE MECHANICAL) › ENGINE UNIT › 2017.09–2018.04
RM33A0E _51 Engine / Hybrid System _065324 2AR-FE ENGINE MECHANICAL _0321408 ENGINE UNIT A

2AR-FE ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Smart Entry and Start System

*2: w/o Smart Entry and Start System

*3: The vehicle height changes because of suspension or tire replacement.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft

(for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of fuel injector assembly

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of knock control sensor

·

Replacement of engine coolant temperature sensor


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly Perform the following procedures in the order shown:
1.

Reset Memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


(Click here)for U760E Initialization
(Click here)for U760E Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
Possible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Impossible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM*1 Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Replacement of ECM*2 Perform code registration (Immobiliser system)
·

Wireless door lock control system

·

Engine start


See Service Bulletin for the registration method.
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly. (Click here)
Suspension, tires*3 Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

PROCEDURE

Hide 11452 1.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.
A195867

Remove the engine oil level dipstick.


b.

Remove the bolt and engine oil level dipstick guide.


c.

Remove the O-ring from the engine oil level dipstick guide.


Hide 17167 4.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 25051 5.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)

Hide 16361A 6.REMOVE V-RIBBED BELT

Hide 27020 7.REMOVE GENERATOR ASSEMBLY

Hide 8.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A412647

Remove the nut and wire harness clamp bracket.


b.
A412648

Remove the bolt and wire harness clamp bracket.


c.
A412649

Remove the bolt and wire harness clamp bracket.


Hide 88310 9.REMOVE COMPRESSOR ASSEMBLY WITH PULLEY

a.

for Type A:

i.
E372030C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 2 bolts and 2 nuts.


ii.
E372031

Using an E8 "TORX" socket wrench, remove the 2 stud bolts.



b.

for Type B:

i.
E372032

Remove the 4 bolts.



c.

Remove the compressor assembly with pulley.


Hide 43457 10.REMOVE DRIVE SHAFT BEARING BRACKET

a.
A407955

Remove the 3 bolts and drive shaft bearing bracket.


Hide 88431 11.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

a.
A210230

Remove the 4 bolts and No. 1 compressor mounting bracket.


Hide 22030 12.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 22271 13.REMOVE THROTTLE BODY GASKET

Hide 14.REMOVE WATER BY-PASS HOSE

a.
A196855

Slide the 2 clips and remove the No. 2 water by-pass hose and No. 1 water by-pass hose.


Hide 17650 15.REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)

Hide 12262 16.DISCONNECT NO. 2 VENTILATION HOSE

Hide 23814B 17.REMOVE FUEL DELIVERY PIPE

Hide 23891 18.REMOVE FUEL DELIVERY SPACER

Hide 23291 19.REMOVE INJECTOR VIBRATION INSULATOR

Hide 23250 20.REMOVE FUEL INJECTOR ASSEMBLY

Hide 82219A 22.REMOVE SENSOR WIRE

a.
A407996

Disconnect the knock control sensor connector.


b.

Remove the bolt and sensor wire from the cylinder block sub-assembly.


Hide 89615 23.REMOVE KNOCK CONTROL SENSOR

Hide 83530 24.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 89422 25.REMOVE ENGINE COOLANT TEMPERATURE SENSOR