Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › 2017.09–2017.12
RM33A0E _51 Engine / Hybrid System _065333 2GR-FKS ENGINE MECHANICAL _0327367 CYLINDER HEAD GASKET A

2GR-FKS ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during cylinder head gasket removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of fuel injector assembly (for port injection)

·

Replacement of fuel injector assembly (for direct injection)

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of ignition coil assembly

·

Air leaks from intake system

·

Gas leak from exhaust system is repaired

·

Replacement of knock control sensor


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly
1.

Reset Memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for Initialization
(Click here)
for Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
for Initialization
(Click here)
for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

PROCEDURE

Hide 1.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

Hide 89615 3.REMOVE KNOCK CONTROL SENSOR

Hide 29300 5.REMOVE VACUUM PUMP ASSEMBLY

Hide 16361A 6.REMOVE V-RIBBED BELT

Hide 27020 7.REMOVE GENERATOR ASSEMBLY

Hide 8.REMOVE COMPRESSOR ASSEMBLY WITH MAGNETIC CLUTCH

Hide 16604 9.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 16620 10.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 16173 11.REMOVE WATER PUMP PULLEY

Hide 11452 12.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 13.REMOVE WIRE HARNESS CLAMP BRACKET

Hide 16522 14.REMOVE WATER FILLER BRACKET

Hide 12315 16.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

Hide 16261 17.DISCONNECT WATER BY-PASS HOSE

Hide 16031 18.REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Hide 15370 19.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1)

Hide 15370 20.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1)

Hide 15370 21.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2)

Hide 15370 22.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2)

Hide 11401Q 23.REMOVE VVT SENSOR (for Intake Side of Bank 1)

Hide 11401M 24.REMOVE VVT SENSOR (for Exhaust Side of Bank 1)

Hide 11401M 25.REMOVE VVT SENSOR (for Intake Side of Bank 2)

Hide 11401M 26.REMOVE VVT SENSOR (for Exhaust Side of Bank 2)

Hide 19312 27.REMOVE CRANKSHAFT POSITION SENSOR PROTECTOR

Hide 11201 29.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11202 30.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 11193 31.REMOVE SPARK PLUG TUBE GASKET

Hide 12102A 32.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Hide 15104 33.REMOVE OIL STRAINER SUB-ASSEMBLY

Hide 12101 34.REMOVE OIL PAN SUB-ASSEMBLY

a.
A366043C03
2.552,1.99 2.958,2.177 0.406,0.188 10 true *a 2.333,0 2.667,0.198 0.333,0.198 10 true *a
*a Nut


Remove the 16 bolts and 2 nuts from the oil pan sub-assembly.

NOTICE:

Make sure to clean the bolts and stud bolts and check the threads for cracks or other damage.



b.
A366105C01
0.635,0.552 2.906,0.25 2.906,0.25 2.823,2.563 true 0.635,2.833 2.896,0.26 true 2.948,0.104 3.26,0.26 0.313,0.156 10 false *a
*a Protective Tape


Remove the oil pan sub-assembly by prying between the oil pan sub-assembly and timing chain cover assembly or cylinder block sub-assembly with a screwdriver wrapped with protective tape.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly, timing chain cover assembly and oil pan sub-assembly.



c.
A366106

Remove the 2 oil pan gaskets from the timing chain cover assembly.


Hide 11310 35.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 11301C 36.REMOVE TIMING CHAIN CASE OIL SEAL

Hide 37.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 13540 38.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 39.REMOVE CHAIN TENSIONER SLIPPER

Hide 13050 41.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY, CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1)

Hide 13550 42.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 43.REMOVE CAMSHAFT BEARING CAP (for Bank 1)

Hide 46.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13050 47.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY, CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2)

Hide 13560A 48.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

Hide 49.REMOVE CAMSHAFT BEARING CAP (for Bank 2)

Hide 13053 50.REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY

Hide 13054 51.REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY

Hide 11104A 52.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

Hide 13561 54.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13562 55.REMOVE NO. 2 CHAIN VIBRATION DAMPER

Hide 13801 56.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 57.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 60.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 61.REMOVE CYLINDER HEAD GASKET

a.

Remove the cylinder head gasket from the cylinder block sub-assembly.


Hide 11116 63.REMOVE NO. 2 CYLINDER HEAD GASKET

a.

Remove the No. 2 cylinder head gasket from the cylinder block sub-assembly.


Hide 11101A 64.INSPECT CYLINDER HEAD SET BOLT