12108
1.REMOVE OIL FILLER CAP SUB-ASSEMBLY
Remove the oil filler cap sub-assembly from the cylinder head cover sub-assembly LH.
Remove the oil filler cap gasket from the oil filler cap sub-assembly.
19100P
2.REMOVE SPARK PLUG
12204
3.REMOVE PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)
11415
4.REMOVE TAPER SCREW PLUG
Remove the taper screw plug from the cylinder block sub-assembly.
11415
5.REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
Remove the cylinder block water drain cock plug from the cylinder block water drain cock sub-assembly.
Remove the cylinder block water drain cock sub-assembly from the cylinder block sub-assembly.
13471
6.REMOVE CRANKSHAFT PULLEY
12315
7.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH
Remove the 7 bolts and front No. 1 engine mounting bracket LH from the timing chain cover assembly.
16261
8.REMOVE WATER BY-PASS HOSE
Slide the 2 clips and remove the water by-pass hose from the water inlet pipe and water inlet with thermostat sub-assembly.
16031
9.REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
15370
10.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1)
15370
11.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1)
15370
12.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2)
15370
13.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2)
11401Q
14.REMOVE VVT SENSOR (for Intake Side of Bank 1)
11401M
15.REMOVE VVT SENSOR (for Exhaust Side of Bank 1)
11401M
16.REMOVE VVT SENSOR (for Intake Side of Bank 2)
11401M
17.REMOVE VVT SENSOR (for Exhaust Side of Bank 2)
19312
18.REMOVE CRANKSHAFT POSITION SENSOR PROTECTOR
11401G
19.REMOVE CRANKSHAFT POSITION SENSOR
89422
20.REMOVE ENGINE COOLANT TEMPERATURE SENSOR
16331
21.REMOVE WATER OUTLET
|
Bolt |
|
Nut |
Remove the 4 bolts, 2 nuts and water outlet from the cylinder head sub-assembly and cylinder head LH.
Remove the 2 No. 2 water inlet housing gaskets from the water outlet.
11201
22.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Remove the 2 clips and No. 1 engine cover sub-assembly from the cylinder head cover sub-assembly.
Remove the 13 bolts and cylinder head cover sub-assembly from the camshaft housing sub-assembly.
Remove the camshaft bearing cap oil hole gasket from the camshaft bearing cap.
Remove the 3 cylinder head cover gaskets from the cylinder head cover sub-assembly.
11202
23.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
Remove the No. 1 V-bank cover bracket from the cylinder head cover sub-assembly LH.
Remove the 14 bolts and cylinder head cover sub-assembly LH from the camshaft housing sub-assembly LH.
Remove the camshaft bearing cap oil hole gasket LH from the camshaft bearing cap.
Remove the 3 No. 2 cylinder head cover gaskets from the cylinder head cover sub-assembly LH.
11193
24.REMOVE SPARK PLUG TUBE GASKET
| *a | Protective Tape |
Using a screwdriver as shown in the illustration, deform each spark plug tube gasket inwards and remove the 6 spark plug tube gaskets from the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.
12101A
25.REMOVE OIL PAN DRAIN PLUG
Remove the oil pan drain plug and oil pan drain plug gasket from the No. 2 oil pan sub-assembly.
15620
26.REMOVE OIL FILTER CAP ASSEMBLY
83530
27.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY
12102A
28.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
Remove the 15 bolts and 2 nuts from the No. 2 oil pan sub-assembly.
Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and No. 2 oil pan sub-assembly. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.
Be careful not to damage the contact surfaces of the oil pans.
15104
29.REMOVE OIL STRAINER SUB-ASSEMBLY
Remove the 2 nuts and oil strainer sub-assembly from the timing chain cover assembly.
Remove the oil strainer gasket from the oil strainer sub-assembly.
89491
30.REMOVE ENGINE OIL LEVEL SENSOR
12101
31.REMOVE OIL PAN SUB-ASSEMBLY
15679
32.REMOVE OIL FILTER BRACKET CLIP
Remove the oil filter bracket clip from the oil pan sub-assembly.
12121
33.REMOVE NO. 1 OIL PAN BAFFLE PLATE
Remove the 8 bolts and No. 1 oil pan baffle plate from the crankshaft bearing cap set bolt.
11324
34.REMOVE TIMING CHAIN COVER PLATE
Remove the 4 bolts, timing chain cover plate and timing chain cover gasket from the timing chain cover assembly.
11301C
35.REMOVE TIMING CHAIN CASE OIL SEAL
11310
36.REMOVE TIMING CHAIN COVER ASSEMBLY
16100
37.REMOVE ENGINE WATER PUMP ASSEMBLY
Remove the 7 bolts, engine water pump assembly and water pump gasket from the timing chain cover assembly.
38.SET NO. 1 CYLINDER TO TDC (COMPRESSION)
Temporarily tighten the crankshaft pulley set bolt to the crankshaft.
| *a | Center Line |
| *b | Key Groove |
Turn the crankshaft clockwise to align the timing mark of the crankshaft timing sprocket key groove chase position with the center line of the block bore (for Bank 1) (TDC / compression).
Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are aligned with the timing marks of the camshaft bearing caps as shown in the illustration.
| *a | Timing Mark | *b | Viewpoint |
Check each timing mark from a viewpoint directly in line with the center of the camshaft and the timing mark on each camshaft timing gear assembly and each camshaft timing exhaust gear assembly.
If the timing marks are checked from any other viewpoint, the valve timing may appear misaligned.
If not aligned, turn the crankshaft 1 revolution (360°) clockwise and align the timing marks as shown in the illustration.
For the camshaft or No. 3 camshaft sub-assembly:
Be sure to check the mark (A) at the point where the marks (B), (C) and (D) are positioned in line. If the marks are checked from any other viewpoint, they cannot be checked correctly.
13540
39.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
| *a | Plunger |
| *b | Stopper Plate |
| *c | Pin |
Turn the stopper plate clockwise to release the lock, and push the plunger deep into the No. 1 chain tensioner assembly.
Turn the stopper plate counterclockwise to set the lock, and insert a 1.0 mm (0.0394 in.) diameter pin into the hole of the stopper plate.
Remove the 2 bolts and No. 1 chain tensioner assembly from the cylinder head sub-assembly.
13559
40.REMOVE CHAIN TENSIONER SLIPPER
Remove the chain tensioner slipper from the cylinder block sub-assembly.
13506
41.REMOVE CHAIN SUB-ASSEMBLY
| *a | Center Line |
| *b | Mark |
| *c | Key Groove |
Turn the crankshaft 10° counterclockwise to loosen the chain sub-assembly of the crankshaft timing sprocket.
Remove the crankshaft pulley set bolt from the crankshaft.
Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.
| *A | for Bank 1 |
Turn the camshaft timing gear assembly on bank 1 clockwise (approximately 60°) so that it is positioned as shown in the illustration.
Be sure to loosen the chain sub-assembly between the banks.
Remove the chain sub-assembly from the engine assembly.
13530
42.REMOVE IDLE SPROCKET ASSEMBLY
Using a 10 mm hexagon socket wrench, remove the No. 2 idle gear shaft, idle sprocket assembly and No. 1 idle gear shaft from the cylinder block sub-assembly.
13561
43.REMOVE NO. 1 CHAIN VIBRATION DAMPER
Remove the 2 bolts and No. 1 chain vibration damper from the cylinder head LH and cylinder block sub-assembly.
13562
44.REMOVE NO. 2 CHAIN VIBRATION DAMPER
Remove the 2 No. 2 chain vibration dampers from the cylinder head LH and cylinder head sub-assembly.
13521
45.REMOVE CRANKSHAFT TIMING SPROCKET
Remove the crankshaft timing sprocket from the crankshaft.
13521A
46.REMOVE CRANKSHAFT TIMING GEAR KEY
Remove the 2 crankshaft timing gear keys from the crankshaft.
13050
47.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY, CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1)
| *a | Pin |
| *b | Plunger |
|
Push |
While raising the No. 2 chain tensioner assembly, insert a 1.0 mm (0.0394 in.) diameter pin into the hole to secure the No. 2 chain tensioner assembly.
| *a | Hold |
|
Turn |
Using a wrench to hold the hexagonal portion of camshaft, loosen the camshaft timing gear bolt of the camshaft timing gear assembly.
Be careful not to damage the camshaft, camshaft housing sub-assembly or spark plug tube with wrench.
Do not loosen any other bolt. If any other bolt is loosened, replace the camshaft timing gear assembly and/or the camshaft timing exhaust gear assembly with a new one.
If the camshaft timing gear bolt has been struck or dropped, replace it.
| *a | Hold |
|
Turn |
Using a wrench to hold the hexagonal portion of No. 2 camshaft, loosen the camshaft timing gear bolt of the camshaft timing exhaust gear assembly.
Be careful not to damage the No. 2 camshaft, camshaft housing sub-assembly or spark plug tube with wrench.
Do not loosen any other bolt. If any other bolt is loosened, replace the camshaft timing gear assembly and/or the camshaft timing exhaust gear assembly with a new one.
If the camshaft timing gear bolt has been struck or dropped, replace it.
Remove the 2 camshaft timing gear bolts, camshaft timing gear assembly and camshaft timing exhaust gear assembly together with the No. 2 chain sub-assembly.
13550
48.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY
Remove the bolt and No. 2 chain tensioner assembly from the camshaft housing sub-assembly.
49.REMOVE CAMSHAFT BEARING CAP (for Bank 1)
| *a | Straight Pin |
| *b | Front View |
| *c | 45° |
Check that the camshaft and No. 2 camshaft are positioned as shown in the illustration.
Uniformly loosen and remove the 9 bolts in several steps in the order shown in the illustration.
Uniformly loosen and remove the 15 bolts in several steps in the order shown in the illustration.
Make sure that the camshaft and No. 2 camshaft remain level while uniformly loosening the bolts.
Remove the fuel pump lifter housing from the camshaft housing sub-assembly.
Remove the 5 camshaft bearing caps from the camshaft housing sub-assembly.
Remove the 2 oil control valve filters from the 2 camshaft bearing caps.
13511
50.REMOVE CAMSHAFT
Remove the camshaft from the camshaft housing sub-assembly.
13512
51.REMOVE NO. 2 CAMSHAFT
Remove the No. 2 camshaft from the camshaft housing sub-assembly.
52.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY
| *a | Protective Tape |
Remove the camshaft housing sub-assembly by prying between the cylinder head sub-assembly and camshaft housing sub-assembly with a screwdriver with its tip wrapped with protective tape.
Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly.
13050
53.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY, CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2)
| *a | Pin |
| *b | Plunger |
|
Push |
While pushing down the No. 3 chain tensioner assembly, insert a 1.0 mm (0.0394 in.) diameter pin into the hole to secure the No. 3 chain tensioner assembly.
| *a | Hold |
|
Turn |
Using a wrench to hold the hexagonal portion of No. 3 camshaft sub-assembly, loosen the camshaft timing gear bolt of the camshaft timing gear assembly.
Be careful not to damage the No. 3 camshaft sub-assembly, camshaft housing sub-assembly LH or spark plug tube with wrench.
Do not loosen any other bolt. If any other bolt is loosened, replace the camshaft timing gear assembly and/or the camshaft timing exhaust gear assembly with a new one.
If the camshaft timing gear bolt has been struck or dropped, replace it.
| *a | Hold |
|
Turn |
Using a wrench to hold the hexagonal portion of No. 4 camshaft sub-assembly, loosen the camshaft timing gear bolt of the camshaft timing exhaust gear assembly.
Be careful not to damage the No. 4 camshaft sub-assembly, camshaft housing sub-assembly LH or spark plug tube with wrench.
Do not loosen any other bolt. If any other bolt is loosened, replace the camshaft timing gear assembly and/or the camshaft timing exhaust gear assembly with a new one.
If the camshaft timing gear bolt has been struck or dropped, replace it.
Remove the 2 camshaft timing gear bolts, camshaft timing gear assembly and camshaft timing exhaust gear assembly together with the No. 2 chain sub-assembly.
13560A
54.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY
Remove the bolt and No. 3 chain tensioner assembly from the camshaft housing sub-assembly LH.
55.REMOVE CAMSHAFT BEARING CAP (for Bank 2)
| *a | Straight Pin |
| *b | Front View |
Check that the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly are positioned as shown in the illustration.
Uniformly loosen and remove the 8 bolts in several steps in the order shown in the illustration.
Uniformly loosen and remove the 15 bolts in several steps in the order shown in the illustration.
Make sure that the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly remain level while uniformly loosening the bolts.
Remove the 5 camshaft bearing caps from the camshaft housing sub-assembly LH.
Remove the 2 oil control valve filters from the 2 camshaft bearing caps.
13053
56.REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY
Remove the No. 3 camshaft sub-assembly from the camshaft housing sub-assembly LH.
13054
57.REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY
Remove the No. 4 camshaft sub-assembly from the camshaft housing sub-assembly LH.
11104A
58.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH
| *a | Protective Tape |
Remove the camshaft housing sub-assembly LH by prying between the cylinder head LH and camshaft housing sub-assembly LH with a screwdriver with its tip wrapped with protective tape.
Be careful not to damage the contact surfaces of the cylinder head LH and camshaft housing sub-assembly LH.
13801
59.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Remove the 24 No. 1 valve rocker arm sub-assemblies from the cylinder head sub-assembly and cylinder head LH.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
13750
60.REMOVE VALVE LASH ADJUSTER ASSEMBLY
Remove the 24 valve lash adjuster assemblies from the cylinder head sub-assembly and cylinder head LH.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
13716
61.REMOVE VALVE STEM CAP
Remove the 24 valve stem caps from the cylinder head sub-assembly and cylinder head LH.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
82219A
62.REMOVE SENSOR WIRE
Remove the 3 bolts and sensor wire from the cylinder head LH and cylinder block sub-assembly.
11381
63.REMOVE REAR ENGINE OIL SEAL RETAINER
Remove the 6 bolts from the rear engine oil seal retainer.
| *a | Protective Tape |
|
Pry |
Using a screwdriver with its tip wrapped with protective tape, pry out the rear engine oil seal retainer.
Be careful not to damage the rear engine oil seal retainer.
11381A
64.REMOVE REAR ENGINE OIL SEAL
| *a | Protective Tape |
| *b | Wooden Block |
Place the rear engine oil seal retainer on wooden blocks.
Using a hammer and a screwdriver with its tip wrapped with protective tape, tap out the rear engine oil seal.
Be careful not to damage the rear engine oil seal retainer.
11101
65.REMOVE CYLINDER HEAD SUB-ASSEMBLY
Using a 10 mm bi-hexagon socket wrench, uniformly loosen the 8 cylinder head set bolts in the order shown in the illustration. Remove the 8 cylinder head set bolts and 8 cylinder head set plate washers.
Be careful not to drop the cylinder head set plate washers into the cylinder head sub-assembly.
Warpage or cracking of the cylinder head sub-assembly may result from removing the cylinder head set bolts in the incorrect order.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
Remove the cylinder head sub-assembly from the cylinder block sub-assembly.
11115
66.REMOVE CYLINDER HEAD GASKET
11102
67.REMOVE CYLINDER HEAD LH
Uniformly loosen and remove the 2 bolts in several steps in the order shown in the illustration.
Using a 10 mm bi-hexagon socket wrench, uniformly loosen the 8 cylinder head set bolts in the order shown in the illustration. Remove the 8 cylinder head set bolts and 8 cylinder head set plate washers.
Be careful not to drop the cylinder head set plate washers into the cylinder head LH.
Warpage or cracking of the cylinder head LH may result from removing the cylinder head set bolts in the incorrect order.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
Remove the cylinder head LH from the cylinder block sub-assembly.
11116
68.REMOVE NO. 2 CYLINDER HEAD GASKET
16322
69.REMOVE WATER INLET PIPE
Remove the 2 bolts and water inlet pipe from the cylinder block sub-assembly.
11114A
70.REMOVE STRAIGHT PIN
It is not necessary to remove the straight pins unless they are being replaced.
11151A
71.REMOVE CAMSHAFT BEARING CAP SETTING RING PIN
It is not necessary to remove the camshaft bearing cap setting ring pins unless they are being replaced.
72.REMOVE STUD BOLT
If a stud bolt is deformed or its threads are damaged, replace it.